FreeBSD 11.0-RC3 и Intel S1200SPL

Решение проблем связванных с работой железа. Проблемы программно-аппаратной совместимости.
Правила форума
Убедительная просьба юзать теги [code] при оформлении листингов.
Сообщения не оформленные должным образом имеют все шансы быть незамеченными.
Аватара пользователя
ommm
рядовой
Сообщения: 39
Зарегистрирован: 2011-01-28 15:18:48

FreeBSD 11.0-RC3 и Intel S1200SPL

Непрочитанное сообщение ommm » 2016-09-18 17:44:37

Ребят помогите пожалуйста с настройкой оборотов кулеров на мат.плате Intel S1200SPL :oops:
софт почему то кулера не видит

# chm -I

Код: Выделить всё

Using ISA Method.
----------------------------------------
Motherboard Temperature: 255 ▒ C
CPU_0 Temperature: 0 ▒ C
CPU_1 Temperature: 0 ▒ C
VCore:   3.98438 V
Vit:     3.98438 V
Vio:     3.98438 V
+5V:     6.65391 V
+12V:    15.9375 V
-12V:    -15.9375 V
-5V:     -6.65391 V
Fan 1: Not Available
Fan 2: Not Available
Fan 3: Not Available


# ipmi-sensors

Код: Выделить всё

ID | Name             | Type                        | Reading    | Units | Event
1  | Pwr Unit Status  | Power Unit                  | N/A        | N/A   | 'OK'
2  | IPMI Watchdog    | Watchdog 2                  | N/A        | N/A   | 'OK'
3  | Physical Scrty   | Physical Security           | N/A        | N/A   | 'General Chassis Intrusion'
4  | FP NMI Diag Int  | Critical Interrupt          | N/A        | N/A   | 'OK'
5  | SMI Timeout      | OEM Reserved                | N/A        | N/A   | 'OK'
6  | System Event Log | Event Logging Disabled      | N/A        | N/A   | 'OK'
7  | System Event     | System Event                | N/A        | N/A   | 'OK'
8  | Button           | Button/Switch               | N/A        | N/A   | 'OK'
9  | BMC Watchdog     | Management Subsystem Health | N/A        | N/A   | 'OK'
10 | VR Watchdog      | Voltage                     | N/A        | N/A   | 'OK'
11 | SSB Therm Trip   | Temperature                 | N/A        | N/A   | 'OK'
12 | IO Mod Presence  | Module/Board                | N/A        | N/A   | 'OK'
13 | SAS Mod Presence | Module/Board                | N/A        | N/A   | 'OK'
14 | BMC FW Health    | Management Subsystem Health | N/A        | N/A   | 'sensor failure'
18 | BB P1 VR Temp    | Temperature                 | -75.00     | C     | 'OK'
19 | P1 VR Ctrl Temp  | Temperature                 | N/A        | C     | N/A
20 | Front Panel Temp | Temperature                 | N/A        | C     | N/A
21 | SSB Temp         | Temperature                 | 34.00      | C     | 'OK'
22 | BB Inlet Temp    | Temperature                 | 25.00      | C     | 'OK'
23 | BB BMC Temp      | Temperature                 | 34.00      | C     | 'OK'
24 | BB Mem VR temp   | Temperature                 | -71.00     | C     | 'OK'
25 | CATERR           | Processor                   | N/A        | N/A   | 'OK'
27 | VRD Hot          | Temperature                 | N/A        | N/A   | 'OK'
28 | BB +12.0V        | Voltage                     | 12.32      | V     | 'OK'
29 | BB +3.3V Vbat    | Voltage                     | 3.16       | V     | 'OK'
30 | Voltage Fault    | Voltage                     | N/A        | N/A   | 'OK'
34 | NM Capabilities  | OEM Reserved                | N/A        | N/A   | N/A
38 | MTT CPU1         | Memory                      | N/A        | %     | N/A


зы. сижу рядом с серваком.. очень противно жужжит :(

Отправлено спустя 13 минут 5 секунд:
# dmesg

Код: Выделить всё

Copyright (c) 1992-2016 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 11.0-RC3 #0 r305786: Wed Sep 14 02:19:25 UTC 2016
    root@releng2.nyi.freebsd.org:/usr/obj/usr/src/sys/GENERIC amd64
FreeBSD clang version 3.8.0 (tags/RELEASE_380/final 262564) (based on LLVM 3.8.0)
VT(vga): resolution 640x480
CPU: Intel(R) Xeon(R) CPU E3-1245 v5 @ 3.50GHz (3504.17-MHz K8-class CPU)
  Origin="GenuineIntel"  Id=0x506e3  Family=0x6  Model=0x5e  Stepping=3
  Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Features2=0x7ffafbff<SSE3,PCLMULQDQ,DTES64,MON,DS_CPL,VMX,SMX,EST,TM2,SSSE3,SDBG,FMA,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,TSCDLT,AESNI,XSAVE,OSXSAVE,AVX,F16C,RDRAND>
  AMD Features=0x2c100800<SYSCALL,NX,Page1GB,RDTSCP,LM>
  AMD Features2=0x121<LAHF,ABM,Prefetch>
  Structured Extended Features=0x29c6fbf<FSGSBASE,TSCADJ,SGX,BMI1,HLE,AVX2,SMEP,BMI2,ERMS,INVPCID,RTM,NFPUSG,MPX,RDSEED,ADX,SMAP,CLFLUSHOPT,PROCTRACE>
  XSAVE Features=0xf<XSAVEOPT,XSAVEC,XINUSE,XSAVES>
  VT-x: PAT,HLT,MTF,PAUSE,EPT,UG,VPID
  TSC: P-state invariant, performance statistics
real memory  = 34359738368 (32768 MB)
avail memory = 32891125760 (31367 MB)
Event timer "LAPIC" quality 600
ACPI APIC Table: <INTEL  S1200SPL>
FreeBSD/SMP: Multiprocessor System Detected: 8 CPUs
FreeBSD/SMP: 1 package(s) x 4 core(s) x 2 hardware threads
random: unblocking device.
ioapic0 <Version 2.0> irqs 0-119 on motherboard
random: entropy device external interface
kbd1 at kbdmux0
netmap: loaded module
module_register_init: MOD_LOAD (vesa, 0xffffffff8101c950, 0) error 19
random: registering fast source Intel Secure Key RNG
random: fast provider: "Intel Secure Key RNG"
vtvga0: <VT VGA driver> on motherboard
cryptosoft0: <software crypto> on motherboard
acpi0: <INTEL S1200SPL> on motherboard
acpi0: Power Button (fixed)
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
cpu2: <ACPI CPU> on acpi0
cpu3: <ACPI CPU> on acpi0
cpu4: <ACPI CPU> on acpi0
cpu5: <ACPI CPU> on acpi0
cpu6: <ACPI CPU> on acpi0
cpu7: <ACPI CPU> on acpi0
hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
Timecounter "HPET" frequency 24000000 Hz quality 950
Event timer "HPET" frequency 24000000 Hz quality 550
atrtc0: <AT realtime clock> port 0x70-0x77 irq 8 on acpi0
atrtc0: Warning: Couldn't map I/O.
Event timer "RTC" frequency 32768 Hz quality 0
attimer0: <AT timer> port 0x40-0x43,0x50-0x53 irq 0 on acpi0
Timecounter "i8254" frequency 1193182 Hz quality 0
Event timer "i8254" frequency 1193182 Hz quality 100
Timecounter "ACPI-fast" frequency 3579545 Hz quality 900
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1808-0x180b on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pcib2: <ACPI PCI-PCI bridge> irq 16 at device 1.1 on pci0
pci2: <ACPI PCI bus> on pcib2
mps0: <Avago Technologies (LSI) SAS2004> port 0x5000-0x50ff mem 0xab140000-0xab143fff,0xaad00000-0xaad3ffff irq 17 at device 0.0 on pci2
mps0: Firmware: 20.00.07.00, Driver: 21.01.00.00-fbsd
mps0: IOCCapabilities: 1285c<ScsiTaskFull,DiagTrace,SnapBuf,EEDP,TransRetry,EventReplay,HostDisc>
vgapci0: <VGA-compatible display> port 0x6000-0x603f mem 0xa9000000-0xa9ffffff,0xa0000000-0xa7ffffff irq 16 at device 2.0 on pci0
vgapci0: Boot video device
xhci0: <Intel Sunrise Point USB 3.0 controller> mem 0xab200000-0xab20ffff irq 16 at device 20.0 on pci0
xhci0: 32 bytes context size, 64-bit DMA
usbus0: waiting for BIOS to give up control
usbus0 on xhci0
pci0: <simple comms> at device 22.0 (no driver attached)
pci0: <simple comms> at device 22.1 (no driver attached)
ahci0: <Intel Sunrise Point AHCI SATA controller> port 0x6080-0x6087,0x6088-0x608b,0x6060-0x607f mem 0xab214000-0xab215fff,0xab219000-0xab2190ff,0xab218000-0xab2187ff irq 16 at device 23.0 on pci0
ahci0: AHCI v1.31 with 8 6Gbps ports, Port Multiplier not supported
ahcich0: <AHCI channel> at channel 0 on ahci0
ahcich1: <AHCI channel> at channel 1 on ahci0
ahcich2: <AHCI channel> at channel 2 on ahci0
ahcich3: <AHCI channel> at channel 3 on ahci0
ahcich4: <AHCI channel> at channel 4 on ahci0
ahcich5: <AHCI channel> at channel 5 on ahci0
ahcich6: <AHCI channel> at channel 6 on ahci0
ahcich7: <AHCI channel> at channel 7 on ahci0
ahciem0: <AHCI enclosure management bridge> on ahci0
pcib3: <ACPI PCI-PCI bridge> irq 17 at device 29.0 on pci0
pci3: <ACPI PCI bus> on pcib3
vgapci1: <VGA-compatible display> mem 0xa8000000-0xa8ffffff,0xaa800000-0xaa803fff,0xaa000000-0xaa7fffff irq 17 at device 0.0 on pci3
pcib4: <ACPI PCI-PCI bridge> irq 18 at device 29.2 on pci0
pci4: <ACPI PCI bus> on pcib4
igb0: <Intel(R) PRO/1000 Network Connection, Version - 2.5.3-k> port 0x4000-0x401f mem 0xaab00000-0xaabfffff,0xaac00000-0xaac03fff irq 18 at device 0.0 on pci4
igb0: Using MSIX interrupts with 5 vectors
igb0: Ethernet address: 00:1e:67:df:a3:a6
igb0: Bound queue 0 to cpu 0
igb0: Bound queue 1 to cpu 1
igb0: Bound queue 2 to cpu 2
igb0: Bound queue 3 to cpu 3
igb0: netmap queues/slots: TX 4/1024, RX 4/1024
pcib5: <ACPI PCI-PCI bridge> irq 19 at device 29.3 on pci0
pci5: <ACPI PCI bus> on pcib5
igb1: <Intel(R) PRO/1000 Network Connection, Version - 2.5.3-k> port 0x3000-0x301f mem 0xaa900000-0xaa9fffff,0xaaa00000-0xaaa03fff irq 19 at device 0.0 on pci5
igb1: Using MSIX interrupts with 5 vectors
igb1: Ethernet address: 00:1e:67:df:a3:a7
igb1: Bound queue 0 to cpu 4
igb1: Bound queue 1 to cpu 5
igb1: Bound queue 2 to cpu 6
igb1: Bound queue 3 to cpu 7
igb1: netmap queues/slots: TX 4/1024, RX 4/1024
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
pci0: <memory> at device 31.2 (no driver attached)
acpi_button0: <Sleep Button> on acpi0
acpi_tz0: <Thermal Zone> on acpi0
acpi_tz1: <Thermal Zone> on acpi0
battery0: <ACPI Control Method Battery> on acpi0
battery1: <ACPI Control Method Battery> on acpi0
battery2: <ACPI Control Method Battery> on acpi0
ppc1: cannot reserve I/O port range
orm0: <ISA Option ROM> at iomem 0xc0000-0xc7fff on isa0
ppc0: cannot reserve I/O port range
est0: <Enhanced SpeedStep Frequency Control> on cpu0
est1: <Enhanced SpeedStep Frequency Control> on cpu1
est2: <Enhanced SpeedStep Frequency Control> on cpu2
est3: <Enhanced SpeedStep Frequency Control> on cpu3
est4: <Enhanced SpeedStep Frequency Control> on cpu4
est5: <Enhanced SpeedStep Frequency Control> on cpu5
est6: <Enhanced SpeedStep Frequency Control> on cpu6
est7: <Enhanced SpeedStep Frequency Control> on cpu7
ZFS filesystem version: 5
ZFS storage pool version: features support (5000)
Timecounters tick every 1.000 msec
usbus0: 5.0Gbps Super Speed USB v3.0
nvme cam probe device init
ugen0.1: <0x8086> at usbus0
uhub0: <0x8086 XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus0
ada0 at ahcich0 bus 0 scbus1 target 0 lun 0
ada0: <Hitachi HDS721050CLA362 JP2OA39C> ATA8-ACS SATA 2.x device
ada0: Serial Number JVH511HN2VR2DV
ada0: 300.000MB/s transfers (SATA 2.x, UDMA6, PIO 8192bytes)
ada0: Command Queueing enabled
ada0: 476940MB (976773168 512 byte sectors)
(da0:mps0:0:0:0): UNMAPPED
(da1:da0 at mps0 bus 0 scbus0 target 0 lun 0
da0: <IBM-ESXS ST2000NM0023 BC5G> Fixed Direct Access SPC-4 SCSI device
da0: Serial Number Z1H0419F000093331S13
da0: 600.000MB/s transfers
da0: Command Queueing enabled
da0: 1907729MB (3907029168 512 byte sectors)
mps0:0:1:0): UNMAPPED
da1 at mps0 bus 0 scbus0 target 1 lun 0
da1: <IBM-ESXS ST2000NM0023 BC5G> Fixed Direct Access SPC-4 SCSI device
da1: Serial Number Z1X14KRE0000V4121A49
da1: 600.000MB/s transfers
da1: Command Queueing enabled
da1: 1907729MB (3907029168 512 byte sectors)
ses0 at ahciem0 bus 0 scbus9 target 0 lun 0
ses0: <AHCI SGPIO Enclosure 1.00 0001> SEMB S-E-S 2.00 device
ses0: SEMB SES Device
SMP: AP CPU #1 Launched!
SMP: AP CPU #2 Launched!
SMP: AP CPU #7 Launched!
SMP: AP CPU #4 Launched!
SMP: AP CPU #5 Launched!
SMP: AP CPU #3 Launched!
SMP: AP CPU #6 Launched!
Timecounter "TSC-low" frequency 1752086613 Hz quality 1000
Trying to mount root from zfs:zpool/ROOT/default []...
Root mount waiting for: usbus0
uhub0: 26 ports with 26 removable, self powered
Root mount waiting for: usbus0
ugen0.2: <American Megatrends Inc.> at usbus0
ukbd0: <Keyboard Interface> on usbus0
kbd2 at ukbd0
Root mount waiting for: usbus0
ugen0.3: <Kingston> at usbus0
umass0: <Kingston DataTraveler 410, class 0/0, rev 2.00/1.00, addr 2> on usbus0
umass0:  SCSI over Bulk-Only; quirks = 0x8100
umass0:10:0: Attached to scbus10
Root mount waiting for: usbus0
da2 at umass-sim0 bus 0 scbus10 target 0 lun 0
da2: <Kingston DataTraveler 410 PMAP> Removable Direct Access SCSI device
da2: Serial Number 0018F30C9FEABAA1C10D0077
da2: 40.000MB/s transfers
da2: 3844MB (7872512 512 byte sectors)
da2: quirks=0x2<NO_6_BYTE>
GEOM: da2: the secondary GPT header is not in the last LBA.
ugen0.4: <APC> at usbus0
igb0: changing name to 'int0'
igb1: changing name to 'int1'
int0: link state changed to UP
ums0: <Mouse Interface> on usbus0
ums0: 3 buttons and [Z] coordinates ID=0
tun0: link state changed to UP
ichsmb0: <Intel Sunrise Point-H SMBus controller> port 0x6040-0x605f mem 0x8bff00000-0x8bff000ff irq 16 at device 31.4 on pci0
smbus0: <System Management Bus> on ichsmb0
ppc1: cannot reserve I/O port range
ipmi0: <IPMI System Interface> on isa0
ipmi0: KCS mode found at io 0xca2 alignment 0x1 on isa
ipmi0: IPMI device rev. 1, firmware rev. 1.03, version 2.0
ipmi0: Number of channels 4
ipmi0: Attached watchdog
ppc0: cannot reserve I/O port range

Аватара пользователя
ommm
рядовой
Сообщения: 39
Зарегистрирован: 2011-01-28 15:18:48

FreeBSD 11.0-RC3 и Intel S1200SPL

Непрочитанное сообщение ommm » 2016-11-07 19:05:39

youngyoung писал(а):зачем оно вам??)если не секрет?

писал выше: сижу рядом с серваком.. очень противно жужжит :(

кстати задачу выше описанную решил обновленной прошивкой SDR (BIOSR01030023_ME040003096_BMC0104r10185_FRUSDR020)

по факту имею серверную мамку и обычный десктопный корпус
и ебствебсвенно столкнулся с отсутствием FrontPanelSensor из за которого систем фэны не определяются и врубаются на максимум)

кому интересно решается подменой FrontPanelSensor на другой (например я заменил на [23] BB P2 VR Temp)
редактируем файл S1200SP.sdr

Код: Выделить всё

//====================================================================//
// Global Stepwise Header Records
//====================================================================//
...
   // Global Stepwise Header Record
   00             // Stepwise Header ID
   21             // Input Sensor Number -- (FP)      [b]// 21 поменять на 23 - это BB P2 VR Temp[/b]
   00             // Entity Presence Sensor Number
   64             // Sensor Disabled Control Value
   64             // Sensor Fail Control Value
   64             // Sensor Unavailable Control Value
   00             // Sleep Control Value
   50             // Sleep State and Hysteresis [7:6]-Supported in S1 (1=yes); [5:3]-Negative Hysteresis = 2; [2:0]-Positive Hysteresis = 0
 ...
 //====================================================================//


Вернуться в «Железо»

Кто сейчас на конференции

Сейчас этот форум просматривают: нет зарегистрированных пользователей и 5 гостей