Modem Zyxel Omni pro ee
Факсы не отправляются, принимаются нормально.
Конфиг модема.
Код: Выделить всё
CountryCode: 7
AreaCode: 812
FAXNumber: 4700100
LongDistancePrefix: 1
InternationalPrefix: 011
DialStringRules: etc/dialrules
ServerTracing: 1
SessionTracing: 0xFFF
RecvFileMode: 0600
LogFileMode: 0600
DeviceMode: 0600
RingsBeforeAnswer: 1
SpeakerVolume: off
GettyArgs: ""
NoCarrierRetrys: 1
MaxRecvPages 10
ModemWaitForConnect: 1
Class2Cmd: AT+FCLASS=2.0 # command to enter class 2.0
Class2BORCmd: AT+FBO=0 # bit order for phase B/C/D (direct)
Class2CQCmd: "" # commands to enable copy quality proc.
Class2AbortCmd: AT+FKS # abort session command
Class2CQQueryCmd: AT+FCQ=? # query for copy quality capabilities
Class2DCCQueryCmd: AT+FCC=? # query for modem capabilities
Class2TBCCmd: AT+FPP=0 # setup stream mode
Class2CRCmd: AT+FCR=1 # enable capability to receive
Class2PHCTOCmd: AT+FCT=30 # set phase C timeout parameter
Class2BUGCmd: AT+FBU=1 # enable HDLC frame tracing
Class2LIDCmd: AT+FLI # set local identifier command
Class2DCCCmd: AT+FCC=? # set modem capabilities command
Class2DISCmd: AT+FIS=? # set session parameters command
Class2DDISCmd: "" # disable pre-dial DIS command hack
Class2CIGCmd: AT+FPI # set polling identifier command
Class2NRCmd: AT+FNR=1,1,1,1 # setup status reporting command
Class2PIECmd: AT+FIE=0 # disable interrupt-enable command
Class2PTSCmd: AT+FPS # set post-page status command
Class2PTSQueryCmd: AT+FPS? # set post-page status query command
Class2SPLCmd: AT+FSP # set polling indicator command
Class2NFLOCmd: AT+FLO=0 # set no flow control command
Class2SFLOCmd: AT+FLO=1 # set software flow control command
Class2HFLOCmd: AT+FLO=2 # set hardware flow control commandКод: Выделить всё
Mar 14 15:30:26.12: [ 1403]: SESSION BEGIN 000000073 78124701350
Mar 14 15:30:26.12: [ 1403]: HylaFAX (tm) Version 6.0.5
Mar 14 15:30:26.12: [ 1403]: SEND FAX: JOB 19 DEST 4701350 COMMID 000000073 DEVICE '/dev/ttyu0' FROM 'test <ribak@caits.ru>' USER test
Mar 14 15:30:26.12: [ 1403]: STATE CHANGE: RUNNING -> SENDING
Mar 14 15:30:26.12: [ 1403]: <-- [9:AT+FLO=1\r]
Mar 14 15:30:26.16: [ 1403]: --> [2:OK]
Mar 14 15:30:26.16: [ 1403]: <-- [9:AT+FPP=0\r]
Mar 14 15:30:26.19: [ 1403]: --> [2:OK]
Mar 14 15:30:26.19: [ 1403]: <-- [9:AT+FBO=0\r]
Mar 14 15:30:26.22: [ 1403]: --> [2:OK]
Mar 14 15:30:26.22: [ 1403]: <-- [10:AT+FCT=30\r]
Mar 14 15:30:26.25: [ 1403]: --> [2:OK]
Mar 14 15:30:26.25: [ 1403]: <-- [15:AT+FNR=1,1,1,1\r]
Mar 14 15:30:26.28: [ 1403]: --> [2:OK]
Mar 14 15:30:26.28: [ 1403]: <-- [9:AT+FIE=0\r]
Mar 14 15:30:26.31: [ 1403]: --> [2:OK]
Mar 14 15:30:26.31: [ 1403]: <-- [9:AT+FBU=1\r]
Mar 14 15:30:26.34: [ 1403]: --> [2:OK]
Mar 14 15:30:26.34: [ 1403]: <-- [23:AT+FCC=1,5,2,2,1,0,0,0\r]
Mar 14 15:30:26.38: [ 1403]: --> [2:OK]
Mar 14 15:30:26.38: [ 1403]: DIAL 4701350
Mar 14 15:30:26.38: [ 1403]: <-- [12:ATDP4701350\r]
Mar 14 15:30:54.38: [ 1403]: --> [4:+FCO]
Mar 14 15:30:55.09: [ 1403]: --> [31:+FNF:"AD 00 36 04 00 00 00 00 "]
Mar 14 15:30:55.09: [ 1403]: REMOTE NSF ""AD 00 36 04 00 00 00 00 ""
Mar 14 15:30:55.09: [ 1403]: NSF remote fax equipment: unknown
Mar 14 15:30:55.53: [ 1403]: --> [27:+FCI:" 4700100"]
Mar 14 15:30:55.53: [ 1403]: REMOTE CSI "4700100"
Mar 14 15:30:55.54: [ 1403]: --> [20:+FIS:1,5,0,2,1,0,0,0]
Mar 14 15:30:55.54: [ 1403]: --> [2:OK]
Mar 14 15:30:55.54: [ 1403]: REMOTE best rate 14400 bit/s
Mar 14 15:30:55.54: [ 1403]: REMOTE max A4 page width (215 mm)
Mar 14 15:30:55.54: [ 1403]: REMOTE max unlimited page length
Mar 14 15:30:55.54: [ 1403]: REMOTE best vres 7.7 line/mm
Mar 14 15:30:55.54: [ 1403]: REMOTE format support: MH, MR
Mar 14 15:30:55.54: [ 1403]: REMOTE best 0 ms/scanline
Mar 14 15:30:55.54: [ 1403]: USE 14400 bit/s
Mar 14 15:30:55.54: [ 1403]: SEND file "docq/doc23.ps;70"
Mar 14 15:30:55.57: [ 1403]: USE A4 page width (215 mm)
Mar 14 15:30:55.57: [ 1403]: USE unlimited page length
Mar 14 15:30:55.57: [ 1403]: USE 3.85 line/mm
Mar 14 15:30:55.57: [ 1403]: USE 2-D MR
Mar 14 15:30:55.57: [ 1403]: USE 0 ms/scanline
Mar 14 15:30:55.57: [ 1403]: <-- [23:AT+FIS=0,5,0,2,1,0,0,0\r]
Mar 14 15:30:55.61: [ 1403]: --> [2:OK]
Mar 14 15:30:55.61: [ 1403]: <-- [7:AT+FDT\r]
Mar 14 15:31:02.98: [ 1403]: --> [20:+FCS:0,5,0,2,1,0,0,0]
Mar 14 15:31:02.99: [ 1403]: --> [7:CONNECT]
Mar 14 15:31:02.99: [ 1403]: SEND begin page
Mar 14 15:31:02.99: [ 1403]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled
Mar 14 15:31:03.00: [ 1403]: <-- data [1027]
Mar 14 15:31:03.00: [ 1403]: <-- data [1033]
Mar 14 15:31:03.00: [ 1403]: <-- data [1027]
Mar 14 15:31:05.14: [ 1403]: <-- data [1025]
Mar 14 15:31:05.14: [ 1403]: <-- data [62]
Mar 14 15:31:05.14: [ 1403]: SENT 5182 bytes of data
Mar 14 15:31:05.14: [ 1403]: MODEM set XON/XOFF/DRAIN: input interpreted, output generated
Mar 14 15:31:05.96: [ 1403]: SEND end page
Mar 14 15:31:05.96: [ 1403]: SEND send EOP (no more pages or documents)
Mar 14 15:31:05.96: [ 1403]: <-- data [2]
Mar 14 15:31:09.01: [ 1403]: --> [5:ERROR]
Mar 14 15:31:09.01: [ 1403]: <-- [8:AT+FPS?\r]
Mar 14 15:31:09.04: [ 1403]: --> [1:2]
Mar 14 15:31:09.04: [ 1403]: --> [2:OK]
