Страница 1 из 3
hylefax не принимает факсы
Добавлено: 2008-07-28 10:30:13
Vel
Всем привет, ставил по
этой статье. Факсы не принимает, модем настроил на автоответ. С факса когда отправляю, ждёт ответа от моего факс-сервера, не дожидаясь собственно стандартный разрыв. В чём прикол не знаю, логирование в hylafax на мой взгляд примитивное, настраивать ничего не надо толком, запустить /usr/local/sbin/faxsetup и указать устройство в моё случае /dev/cuad0 в /etc/ttys я добавил:
Код: Выделить всё
cuad0 "/usr/local/sbin/faxgetty" dialup on secure
Re: hylefax не принимает факсы
Добавлено: 2008-07-28 10:31:52
zingel
ядро собрано с cuad? comconsole_speed какая? и вообще
Re: hylefax не принимает факсы
Добавлено: 2008-07-28 10:41:31
Vel
Код: Выделить всё
# uname -a
FreeBSD fax.localdomain 7.0-RELEASE FreeBSD 7.0-RELEASE #0: Sun Feb 24 19:59:52 UTC 2008 root@logan.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC i386
GENERIC и так по ходу с cuad собран, модем COMовский ZyXEL OMNI 56K, я его опрашивал, всё ОК
comconsole_speed очевидно 38400
Re: hylefax не принимает факсы
Добавлено: 2008-07-28 10:42:30
zingel
Re: hylefax не принимает факсы
Добавлено: 2008-07-28 10:48:15
Vel
ну я же говорил, что я его опрашивал, всё ок
когда в /etc/ttys не указываю
Код: Выделить всё
cuad0 "/usr/local/sbin/faxgetty" dialup on secure
то:
далее я его опрашивал проблем не возникало, трубу снимал, клал и т.д. весь листинг не вижу смысла приводить
когда в /etc/ttys
Код: Выделить всё
cuad0 "/usr/local/sbin/faxgetty" dialup on secure
то
Re: hylefax не принимает факсы
Добавлено: 2008-07-28 10:51:26
zingel
Re: hylefax не принимает факсы
Добавлено: 2008-07-28 10:55:22
Vel
с модемом вопросов нету:
Код: Выделить всё
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
sio0: [FILTER]
sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
sio1: [FILTER]
..........
...........
..........
HylaFAX:
faxq
hfaxd (without old protocol & without SNPP support)
Re: hylefax не принимает факсы
Добавлено: 2008-07-28 10:56:32
zingel
тогда нужно смотреть, в любом случае логи программы....
Re: hylefax не принимает факсы
Добавлено: 2008-07-28 11:22:41
Vel
/var/spool/hylafax/log/c000000004
Код: Выделить всё
Jul 28 12:14:18.35: [ 706]: SESSION BEGIN 000000004 7495663
Jul 28 12:14:18.35: [ 706]: HylaFAX (tm) Version 4.4.4
Jul 28 12:14:18.35: [ 706]: <-- [4:ATA\r]
Jul 28 12:14:21.71: [ 706]: --> [7:CONNECT]
Jul 28 12:14:21.71: [ 706]: ANSWER: FAX CONNECTION DEVICE '/dev/cuad0'
Jul 28 12:14:21.71: [ 706]: RECV FAX: begin
Jul 28 12:14:21.71: [ 706]: <-- data [32]
Jul 28 12:14:21.71: [ 706]: <-- data [2]
Jul 28 12:14:22.57: [ 706]: --> [7:CONNECT]
Jul 28 12:14:22.57: [ 706]: <-- data [23]
Jul 28 12:14:22.57: [ 706]: <-- data [2]
Jul 28 12:14:23.32: [ 706]: --> [7:CONNECT]
Jul 28 12:14:23.32: [ 706]: <-- data [13]
Jul 28 12:14:23.32: [ 706]: <-- data [2]
Jul 28 12:14:23.58: [ 706]: --> [2:OK]
Jul 28 12:14:23.58: [ 706]: <-- [9:AT+FRH=3\r]
Jul 28 12:14:23.60: [ 706]: --> [7:CONNECT]
Jul 28 12:14:24.60: [ 706]: --> [2:OK]
Jul 28 12:14:24.60: [ 706]: REMOTE TSI "7777777"
Jul 28 12:14:24.60: [ 706]: RECV recv TSI (sender id)
Jul 28 12:14:24.60: [ 706]: <-- [9:AT+FRH=3\r]
Jul 28 12:14:24.61: [ 706]: --> [7:CONNECT]
Jul 28 12:14:24.76: [ 706]: --> [2:OK]
Jul 28 12:14:24.76: [ 706]: <-- [9:AT+FRS=7\r]
Jul 28 12:14:26.43: [ 706]: --> [2:OK]
Jul 28 12:14:26.43: [ 706]: <-- [9:AT+FTH=3\r]
Jul 28 12:14:26.95: [ 706]: --> [7:CONNECT]
Jul 28 12:14:26.95: [ 706]: <-- data [32]
Jul 28 12:14:26.95: [ 706]: <-- data [2]
Jul 28 12:14:27.81: [ 706]: --> [7:CONNECT]
Jul 28 12:14:27.81: [ 706]: <-- data [23]
Jul 28 12:14:27.81: [ 706]: <-- data [2]
Jul 28 12:14:28.55: [ 706]: --> [7:CONNECT]
Jul 28 12:14:28.55: [ 706]: <-- data [13]
Jul 28 12:14:28.55: [ 706]: <-- data [2]
Jul 28 12:14:28.80: [ 706]: --> [2:OK]
Jul 28 12:14:28.80: [ 706]: <-- [9:AT+FRH=3\r]
Jul 28 12:14:28.82: [ 706]: --> [7:CONNECT]
Jul 28 12:14:29.79: [ 706]: --> [2:OK]
Jul 28 12:14:29.79: [ 706]: REMOTE TSI "7777777"
Jul 28 12:14:29.79: [ 706]: RECV recv TSI (sender id)
Jul 28 12:14:29.79: [ 706]: <-- [9:AT+FRH=3\r]
Jul 28 12:14:29.81: [ 706]: --> [7:CONNECT]
Jul 28 12:14:29.95: [ 706]: --> [2:OK]
Jul 28 12:14:29.95: [ 706]: <-- [9:AT+FRS=7\r]
Jul 28 12:14:31.62: [ 706]: --> [2:OK]
Jul 28 12:14:31.62: [ 706]: <-- [9:AT+FTH=3\r]
Jul 28 12:14:32.13: [ 706]: --> [7:CONNECT]
Jul 28 12:14:32.13: [ 706]: <-- data [32]
Jul 28 12:14:32.13: [ 706]: <-- data [2]
Jul 28 12:14:32.98: [ 706]: --> [7:CONNECT]
Jul 28 12:14:32.98: [ 706]: <-- data [23]
Jul 28 12:14:32.98: [ 706]: <-- data [2]
Jul 28 12:14:33.73: [ 706]: --> [7:CONNECT]
Jul 28 12:14:33.73: [ 706]: <-- data [13]
Jul 28 12:14:33.73: [ 706]: <-- data [2]
Jul 28 12:14:33.98: [ 706]: --> [2:OK]
Jul 28 12:14:33.98: [ 706]: <-- [9:AT+FRH=3\r]
Jul 28 12:14:33.99: [ 706]: --> [7:CONNECT]
Jul 28 12:14:34.97: [ 706]: --> [2:OK]
Jul 28 12:14:34.97: [ 706]: REMOTE TSI "7777777"
Jul 28 12:14:34.97: [ 706]: RECV recv TSI (sender id)
Jul 28 12:14:34.97: [ 706]: <-- [9:AT+FRH=3\r]
Jul 28 12:14:34.98: [ 706]: --> [7:CONNECT]
Jul 28 12:14:35.14: [ 706]: --> [2:OK]
Jul 28 12:14:35.14: [ 706]: <-- [9:AT+FRS=7\r]
Jul 28 12:14:36.81: [ 706]: --> [2:OK]
Jul 28 12:14:36.81: [ 706]: <-- [9:AT+FTH=3\r]
Jul 28 12:14:37.33: [ 706]: --> [7:CONNECT]
Jul 28 12:14:37.33: [ 706]: <-- data [32]
Jul 28 12:14:37.33: [ 706]: <-- data [2]
Jul 28 12:14:38.19: [ 706]: --> [7:CONNECT]
Jul 28 12:14:38.19: [ 706]: <-- data [23]
Jul 28 12:14:38.19: [ 706]: <-- data [2]
Jul 28 12:14:38.93: [ 706]: --> [7:CONNECT]
Jul 28 12:14:38.93: [ 706]: <-- data [13]
Jul 28 12:14:38.93: [ 706]: <-- data [2]
Jul 28 12:14:39.19: [ 706]: --> [2:OK]
Jul 28 12:14:39.19: [ 706]: <-- [9:AT+FRH=3\r]
Jul 28 12:14:39.20: [ 706]: --> [7:CONNECT]
Jul 28 12:14:39.89: [ 706]: --> [2:OK]
Jul 28 12:14:39.89: [ 706]: HDLC frame too short (3 bytes)
Jul 28 12:14:39.89: [ 706]: <-- [10:AT+FRS=21\r]
Jul 28 12:14:40.03: [ 706]: --> [2:OK]
Jul 28 12:14:40.03: [ 706]: <-- [9:AT+FTH=3\r]
Jul 28 12:14:40.55: [ 706]: --> [7:CONNECT]
Jul 28 12:14:40.55: [ 706]: <-- data [3]
Jul 28 12:14:40.55: [ 706]: <-- data [2]
Jul 28 12:14:40.67: [ 706]: --> [2:OK]
Jul 28 12:14:40.67: [ 706]: RECV send CRP (command repeat)
Jul 28 12:14:40.67: [ 706]: <-- [9:AT+FRH=3\r]
Jul 28 12:14:40.69: [ 706]: --> [7:CONNECT]
Jul 28 12:14:50.69: [ 706]: <-- data [1]
Jul 28 12:14:50.70: [ 706]: --> [2:OK]
Jul 28 12:14:50.70: [ 706]: <-- [9:AT+FRS=7\r]
Jul 28 12:15:20.70: [ 706]: MODEM <Timeout>
Jul 28 12:15:20.70: [ 706]: Failure to receive silence (synchronization failure).
Jul 28 12:15:20.70: [ 706]: <-- data [1]
Jul 28 12:15:20.71: [ 706]: --> [2:OK]
Jul 28 12:15:20.71: [ 706]: RECV FAX: Failure to receive silence (synchronization failure).
Jul 28 12:15:20.71: [ 706]: RECV FAX: end
Jul 28 12:15:20.71: [ 706]: Failure to receive silence (synchronization failure).
Jul 28 12:15:20.71: [ 706]: SESSION END
коннект то идёт, но почему он факс не хочет принимать
Re: hylefax не принимает факсы
Добавлено: 2008-07-28 14:38:03
Alex Keda
ну, обиделось наверно за неправильное название
))
Re: hylefax не принимает факсы
Добавлено: 2008-07-28 14:48:57
Vel
Погодите, за какое название?
Ещё я такой лог получал:
Код: Выделить всё
Jul 28 13:35:56.67: [ 706]: SESSION BEGIN 000000020 7495663
Jul 28 13:35:56.67: [ 706]: HylaFAX (tm) Version 4.4.4
Jul 28 13:35:56.67: [ 706]: <-- [4:ATA\r]
Jul 28 13:36:00.03: [ 706]: --> [7:CONNECT]
Jul 28 13:36:00.03: [ 706]: ANSWER: FAX CONNECTION DEVICE '/dev/cuad0'
Jul 28 13:36:00.03: [ 706]: RECV FAX: begin
Jul 28 13:36:00.03: [ 706]: <-- data [32]
Jul 28 13:36:00.03: [ 706]: <-- data [2]
Jul 28 13:36:00.90: [ 706]: --> [7:CONNECT]
Jul 28 13:36:00.90: [ 706]: <-- data [23]
Jul 28 13:36:00.90: [ 706]: <-- data [2]
Jul 28 13:36:01.64: [ 706]: --> [7:CONNECT]
Jul 28 13:36:01.64: [ 706]: <-- data [13]
Jul 28 13:36:01.64: [ 706]: <-- data [2]
Jul 28 13:36:01.91: [ 706]: --> [2:OK]
Jul 28 13:36:01.91: [ 706]: <-- [9:AT+FRH=3\r]
Jul 28 13:36:01.93: [ 706]: --> [7:CONNECT]
Jul 28 13:36:11.93: [ 706]: <-- data [1]
Jul 28 13:36:11.94: [ 706]: --> [2:OK]
Jul 28 13:36:11.94: [ 706]: <-- [9:AT+FRS=7\r]
Jul 28 13:36:22.99: [ 706]: --> [2:OK]
Jul 28 13:36:22.99: [ 706]: <-- [9:AT+FTH=3\r]
Jul 28 13:36:23.51: [ 706]: --> [7:CONNECT]
Jul 28 13:36:23.51: [ 706]: <-- data [32]
Jul 28 13:36:23.51: [ 706]: <-- data [2]
Jul 28 13:36:24.38: [ 706]: --> [7:CONNECT]
Jul 28 13:36:24.38: [ 706]: <-- data [23]
Jul 28 13:36:24.38: [ 706]: <-- data [2]
Jul 28 13:36:25.12: [ 706]: --> [7:CONNECT]
Jul 28 13:36:25.12: [ 706]: <-- data [13]
Jul 28 13:36:25.12: [ 706]: <-- data [2]
Jul 28 13:36:25.37: [ 706]: --> [2:OK]
Jul 28 13:36:25.37: [ 706]: <-- [9:AT+FRH=3\r]
Jul 28 13:36:25.38: [ 706]: --> [7:CONNECT]
Jul 28 13:36:25.39: [ 706]: --> [2:OK]
Jul 28 13:36:25.39: [ 706]: HDLC frame too short (3 bytes)
Jul 28 13:36:25.39: [ 706]: <-- [10:AT+FRS=21\r]
Jul 28 13:36:49.50: [ 706]: --> [2:OK]
Jul 28 13:36:49.50: [ 706]: <-- [9:AT+FTH=3\r]
Jul 28 13:36:50.02: [ 706]: --> [7:CONNECT]
Jul 28 13:36:50.02: [ 706]: <-- data [3]
Jul 28 13:36:50.02: [ 706]: <-- data [2]
Jul 28 13:36:50.15: [ 706]: --> [2:OK]
Jul 28 13:36:50.15: [ 706]: RECV send CRP (command repeat)
Jul 28 13:36:50.15: [ 706]: <-- [9:AT+FRH=3\r]
Jul 28 13:36:50.16: [ 706]: --> [7:CONNECT]
Jul 28 13:36:50.17: [ 706]: --> [2:OK]
Jul 28 13:36:50.17: [ 706]: HDLC frame too short (3 bytes)
Jul 28 13:36:50.17: [ 706]: <-- [10:AT+FRS=21\r]
Jul 28 13:36:59.68: [ 706]: --> [2:OK]
Jul 28 13:36:59.68: [ 706]: <-- [9:AT+FTH=3\r]
Jul 28 13:37:00.20: [ 706]: --> [7:CONNECT]
Jul 28 13:37:00.20: [ 706]: <-- data [3]
Jul 28 13:37:00.20: [ 706]: <-- data [2]
Jul 28 13:37:00.31: [ 706]: --> [2:OK]
Jul 28 13:37:00.31: [ 706]: RECV send CRP (command repeat)
Jul 28 13:37:00.31: [ 706]: <-- [9:AT+FRH=3\r]
Jul 28 13:37:00.33: [ 706]: --> [7:CONNECT]
Jul 28 13:37:00.34: [ 706]: --> [2:OK]
Jul 28 13:37:00.34: [ 706]: RECV recv NSF (non-standard facilities)
Jul 28 13:37:00.34: [ 706]: <-- [9:AT+FRH=3\r]
Jul 28 13:37:00.46: [ 706]: --> [7:CONNECT]
Jul 28 13:37:01.16: [ 706]: --> [2:OK]
Jul 28 13:37:01.16: [ 706]: RECV recv CSI (called subscriber id)
Jul 28 13:37:01.16: [ 706]: <-- [9:AT+FRH=3\r]
Jul 28 13:37:01.18: [ 706]: --> [7:CONNECT]
Jul 28 13:37:01.54: [ 706]: --> [2:OK]
Jul 28 13:37:01.54: [ 706]: RECV recv DIS (identification signal)
Jul 28 13:37:01.54: [ 706]: <-- [9:AT+FRH=3\r]
Jul 28 13:37:01.55: [ 706]: --> [7:CONNECT]
Jul 28 13:37:01.74: [ 706]: --> [2:OK]
Jul 28 13:37:01.74: [ 706]: RECV recv NSF (non-standard facilities)
Jul 28 13:37:01.74: [ 706]: <-- [9:AT+FRH=3\r]
Jul 28 13:37:01.76: [ 706]: --> [7:CONNECT]
Jul 28 13:37:01.76: [ 706]: --> [10:NO CARRIER]
Jul 28 13:37:01.76: [ 706]: MODEM No carrier
Jul 28 13:37:01.76: [ 706]: <-- [10:AT+FRS=21\r]
Jul 28 13:37:01.88: [ 706]: --> [2:OK]
Jul 28 13:37:01.88: [ 706]: <-- [9:AT+FTH=3\r]
Jul 28 13:37:02.40: [ 706]: --> [7:CONNECT]
Jul 28 13:37:02.40: [ 706]: <-- data [3]
Jul 28 13:37:02.40: [ 706]: <-- data [2]
Jul 28 13:37:02.53: [ 706]: --> [2:OK]
Jul 28 13:37:02.53: [ 706]: RECV send CRP (command repeat)
Jul 28 13:37:02.53: [ 706]: <-- [9:AT+FRH=3\r]
Jul 28 13:37:02.54: [ 706]: --> [7:CONNECT]
Jul 28 13:37:03.37: [ 706]: --> [2:OK]
Jul 28 13:37:03.37: [ 706]: RECV recv CSI (called subscriber id)
Jul 28 13:37:03.37: [ 706]: <-- [9:AT+FRH=3\r]
Jul 28 13:37:03.39: [ 706]: --> [7:CONNECT]
Jul 28 13:37:03.76: [ 706]: --> [2:OK]
Jul 28 13:37:03.76: [ 706]: RECV recv DIS (identification signal)
Jul 28 13:37:03.76: [ 706]: <-- [9:AT+FRH=3\r]
Jul 28 13:37:03.77: [ 706]: --> [7:CONNECT]
Jul 28 13:37:03.95: [ 706]: --> [2:OK]
Jul 28 13:37:03.95: [ 706]: RECV recv NSF (non-standard facilities)
Jul 28 13:37:03.95: [ 706]: <-- [9:AT+FRH=3\r]
Jul 28 13:37:03.97: [ 706]: --> [7:CONNECT]
Jul 28 13:37:03.98: [ 706]: --> [10:NO CARRIER]
Jul 28 13:37:03.98: [ 706]: MODEM No carrier
Jul 28 13:37:03.98: [ 706]: <-- [10:AT+FRS=21\r]
Jul 28 13:37:04.10: [ 706]: --> [2:OK]
Jul 28 13:37:04.10: [ 706]: <-- [9:AT+FTH=3\r]
Jul 28 13:37:04.62: [ 706]: --> [7:CONNECT]
Jul 28 13:37:04.62: [ 706]: <-- data [3]
Jul 28 13:37:04.62: [ 706]: <-- data [2]
Jul 28 13:37:04.75: [ 706]: --> [2:OK]
Jul 28 13:37:04.75: [ 706]: RECV send CRP (command repeat)
Jul 28 13:37:04.75: [ 706]: <-- [9:AT+FRH=3\r]
Jul 28 13:37:04.76: [ 706]: --> [7:CONNECT]
Jul 28 13:37:05.59: [ 706]: --> [2:OK]
Jul 28 13:37:05.59: [ 706]: RECV recv CSI (called subscriber id)
Jul 28 13:37:05.59: [ 706]: <-- [9:AT+FRH=3\r]
Jul 28 13:37:05.60: [ 706]: --> [7:CONNECT]
Jul 28 13:37:05.97: [ 706]: --> [2:OK]
Jul 28 13:37:05.97: [ 706]: RECV recv DIS (identification signal)
Jul 28 13:37:05.97: [ 706]: <-- [9:AT+FRH=3\r]
Jul 28 13:37:05.99: [ 706]: --> [7:CONNECT]
Jul 28 13:37:06.17: [ 706]: --> [2:OK]
Jul 28 13:37:06.17: [ 706]: RECV recv NSF (non-standard facilities)
Jul 28 13:37:06.17: [ 706]: <-- [9:AT+FRH=3\r]
Jul 28 13:37:06.18: [ 706]: --> [7:CONNECT]
Jul 28 13:37:06.19: [ 706]: --> [10:NO CARRIER]
Jul 28 13:37:06.19: [ 706]: MODEM No carrier
Jul 28 13:37:06.19: [ 706]: <-- [10:AT+FRS=21\r]
Jul 28 13:37:06.31: [ 706]: --> [2:OK]
Jul 28 13:37:06.31: [ 706]: <-- [9:AT+FTH=3\r]
Jul 28 13:37:06.83: [ 706]: --> [7:CONNECT]
Jul 28 13:37:06.83: [ 706]: <-- data [3]
Jul 28 13:37:06.83: [ 706]: <-- data [2]
Jul 28 13:37:06.95: [ 706]: --> [2:OK]
Jul 28 13:37:06.96: [ 706]: RECV send CRP (command repeat)
Jul 28 13:37:06.96: [ 706]: <-- [9:AT+FRH=3\r]
Jul 28 13:37:06.97: [ 706]: --> [7:CONNECT]
Jul 28 13:37:07.80: [ 706]: --> [2:OK]
Jul 28 13:37:07.80: [ 706]: RECV recv CSI (called subscriber id)
Jul 28 13:37:07.80: [ 706]: <-- [9:AT+FRH=3\r]
Jul 28 13:37:07.82: [ 706]: --> [7:CONNECT]
Jul 28 13:37:08.17: [ 706]: --> [2:OK]
Jul 28 13:37:08.18: [ 706]: RECV recv DIS (identification signal)
Jul 28 13:37:08.18: [ 706]: <-- [9:AT+FRH=3\r]
Jul 28 13:37:08.19: [ 706]: --> [7:CONNECT]
Jul 28 13:37:08.37: [ 706]: --> [2:OK]
Jul 28 13:37:08.37: [ 706]: RECV recv NSF (non-standard facilities)
Jul 28 13:37:08.37: [ 706]: <-- [9:AT+FRH=3\r]
Jul 28 13:37:08.39: [ 706]: --> [7:CONNECT]
Jul 28 13:37:08.41: [ 706]: --> [10:NO CARRIER]
Jul 28 13:37:08.41: [ 706]: MODEM No carrier
Jul 28 13:37:08.41: [ 706]: <-- [10:AT+FRS=21\r]
Jul 28 13:37:08.52: [ 706]: --> [2:OK]
Jul 28 13:37:08.53: [ 706]: <-- [9:AT+FTH=3\r]
Jul 28 13:37:09.05: [ 706]: --> [7:CONNECT]
Jul 28 13:37:09.05: [ 706]: <-- data [3]
Jul 28 13:37:09.05: [ 706]: <-- data [2]
Jul 28 13:37:09.17: [ 706]: --> [2:OK]
Jul 28 13:37:09.17: [ 706]: RECV send CRP (command repeat)
Jul 28 13:37:09.17: [ 706]: <-- [9:AT+FRH=3\r]
Jul 28 13:37:09.19: [ 706]: --> [7:CONNECT]
Jul 28 13:37:10.01: [ 706]: --> [2:OK]
Jul 28 13:37:10.01: [ 706]: RECV recv CSI (called subscriber id)
Jul 28 13:37:10.01: [ 706]: <-- [9:AT+FRH=3\r]
Jul 28 13:37:10.02: [ 706]: --> [7:CONNECT]
Jul 28 13:37:10.39: [ 706]: --> [2:OK]
Jul 28 13:37:10.39: [ 706]: RECV recv DIS (identification signal)
Jul 28 13:37:10.39: [ 706]: <-- [9:AT+FRH=3\r]
Jul 28 13:37:10.41: [ 706]: --> [7:CONNECT]
Jul 28 13:37:10.58: [ 706]: --> [2:OK]
Jul 28 13:37:10.58: [ 706]: RECV recv NSF (non-standard facilities)
Jul 28 13:37:10.58: [ 706]: <-- [9:AT+FRH=3\r]
Jul 28 13:37:10.59: [ 706]: --> [7:CONNECT]
Jul 28 13:37:10.61: [ 706]: --> [10:NO CARRIER]
Jul 28 13:37:10.61: [ 706]: MODEM No carrier
Jul 28 13:37:10.61: [ 706]: <-- [10:AT+FRS=21\r]
Jul 28 13:37:10.73: [ 706]: --> [2:OK]
Jul 28 13:37:10.73: [ 706]: <-- [9:AT+FTH=3\r]
Jul 28 13:37:11.25: [ 706]: --> [7:CONNECT]
Jul 28 13:37:11.25: [ 706]: <-- data [3]
Jul 28 13:37:11.25: [ 706]: <-- data [2]
Jul 28 13:37:11.37: [ 706]: --> [2:OK]
Jul 28 13:37:11.37: [ 706]: RECV send CRP (command repeat)
Jul 28 13:37:11.37: [ 706]: <-- [9:AT+FRH=3\r]
Jul 28 13:37:11.39: [ 706]: --> [7:CONNECT]
Jul 28 13:37:12.21: [ 706]: --> [2:OK]
Jul 28 13:37:12.21: [ 706]: RECV recv CSI (called subscriber id)
Jul 28 13:37:12.21: [ 706]: <-- [9:AT+FRH=3\r]
Jul 28 13:37:12.22: [ 706]: --> [7:CONNECT]
Jul 28 13:37:12.58: [ 706]: --> [2:OK]
Jul 28 13:37:12.58: [ 706]: RECV recv DIS (identification signal)
Jul 28 13:37:12.58: [ 706]: <-- [9:AT+FRH=3\r]
Jul 28 13:37:12.60: [ 706]: --> [7:CONNECT]
Jul 28 13:37:12.79: [ 706]: --> [2:OK]
Jul 28 13:37:12.79: [ 706]: RECV recv NSF (non-standard facilities)
Jul 28 13:37:12.79: [ 706]: <-- [9:AT+FRH=3\r]
Jul 28 13:37:12.81: [ 706]: --> [7:CONNECT]
Jul 28 13:37:12.81: [ 706]: --> [10:NO CARRIER]
Jul 28 13:37:12.81: [ 706]: MODEM No carrier
Jul 28 13:37:12.81: [ 706]: <-- [10:AT+FRS=21\r]
Jul 28 13:37:12.92: [ 706]: --> [2:OK]
Jul 28 13:37:12.92: [ 706]: <-- [9:AT+FTH=3\r]
Jul 28 13:37:13.46: [ 706]: --> [7:CONNECT]
Jul 28 13:37:13.46: [ 706]: <-- data [3]
Jul 28 13:37:13.46: [ 706]: <-- data [2]
Jul 28 13:37:13.59: [ 706]: --> [2:OK]
Jul 28 13:37:13.59: [ 706]: RECV send CRP (command repeat)
Jul 28 13:37:13.59: [ 706]: <-- [9:AT+FRH=3\r]
Jul 28 13:37:13.60: [ 706]: --> [7:CONNECT]
Jul 28 13:37:14.47: [ 706]: --> [2:OK]
Jul 28 13:37:14.47: [ 706]: RECV recv CSI (called subscriber id)
Jul 28 13:37:14.47: [ 706]: <-- [9:AT+FRH=3\r]
Jul 28 13:37:14.49: [ 706]: --> [7:CONNECT]
Jul 28 13:37:14.84: [ 706]: --> [2:OK]
Jul 28 13:37:14.84: [ 706]: RECV recv DIS (identification signal)
Jul 28 13:37:14.84: [ 706]: <-- [9:AT+FRH=3\r]
Jul 28 13:37:14.86: [ 706]: --> [7:CONNECT]
Jul 28 13:37:15.03: [ 706]: --> [2:OK]
Jul 28 13:37:15.03: [ 706]: RECV recv NSF (non-standard facilities)
Jul 28 13:37:15.03: [ 706]: <-- [9:AT+FRH=3\r]
Jul 28 13:37:15.05: [ 706]: --> [7:CONNECT]
Jul 28 13:37:15.06: [ 706]: --> [10:NO CARRIER]
Jul 28 13:37:15.06: [ 706]: MODEM No carrier
Jul 28 13:37:15.06: [ 706]: <-- [10:AT+FRS=21\r]
Jul 28 13:37:15.17: [ 706]: --> [2:OK]
Jul 28 13:37:15.17: [ 706]: <-- [9:AT+FTH=3\r]
Jul 28 13:37:15.69: [ 706]: --> [7:CONNECT]
Jul 28 13:37:15.69: [ 706]: <-- data [3]
Jul 28 13:37:15.69: [ 706]: <-- data [2]
Jul 28 13:37:15.81: [ 706]: --> [2:OK]
Jul 28 13:37:15.81: [ 706]: RECV send CRP (command repeat)
Jul 28 13:37:15.81: [ 706]: <-- [9:AT+FRH=3\r]
Jul 28 13:37:15.82: [ 706]: --> [7:CONNECT]
Jul 28 13:37:16.64: [ 706]: --> [2:OK]
Jul 28 13:37:16.64: [ 706]: RECV recv CSI (called subscriber id)
Jul 28 13:37:16.64: [ 706]: <-- [9:AT+FRH=3\r]
Jul 28 13:37:16.65: [ 706]: --> [7:CONNECT]
Jul 28 13:37:17.02: [ 706]: --> [2:OK]
Jul 28 13:37:17.02: [ 706]: RECV recv DIS (identification signal)
Jul 28 13:37:17.02: [ 706]: <-- [9:AT+FRH=3\r]
Jul 28 13:37:17.03: [ 706]: --> [7:CONNECT]
Jul 28 13:37:17.22: [ 706]: --> [2:OK]
Jul 28 13:37:17.22: [ 706]: RECV recv NSF (non-standard facilities)
Jul 28 13:37:17.22: [ 706]: <-- [9:AT+FRH=3\r]
Jul 28 13:37:17.23: [ 706]: --> [7:CONNECT]
Jul 28 13:37:17.25: [ 706]: --> [10:NO CARRIER]
Jul 28 13:37:17.25: [ 706]: MODEM No carrier
Jul 28 13:37:17.25: [ 706]: <-- [10:AT+FRS=21\r]
Jul 28 13:37:17.37: [ 706]: --> [2:OK]
Jul 28 13:37:17.37: [ 706]: <-- [9:AT+FTH=3\r]
Jul 28 13:37:17.90: [ 706]: --> [7:CONNECT]
Jul 28 13:37:17.90: [ 706]: <-- data [3]
Jul 28 13:37:17.90: [ 706]: <-- data [2]
Jul 28 13:37:18.02: [ 706]: --> [2:OK]
Jul 28 13:37:18.02: [ 706]: RECV send CRP (command repeat)
Jul 28 13:37:18.02: [ 706]: <-- [9:AT+FRH=3\r]
Jul 28 13:37:18.03: [ 706]: --> [7:CONNECT]
Jul 28 13:37:18.74: [ 706]: --> [2:OK]
Jul 28 13:37:18.74: [ 706]: RECV recv CSI (called subscriber id)
Jul 28 13:37:18.74: [ 706]: <-- [9:AT+FRH=3\r]
Jul 28 13:37:18.75: [ 706]: --> [7:CONNECT]
Jul 28 13:37:18.77: [ 706]: --> [10:NO CARRIER]
Jul 28 13:37:18.77: [ 706]: MODEM No carrier
Jul 28 13:37:18.77: [ 706]: <-- [10:AT+FRS=21\r]
Jul 28 13:37:18.89: [ 706]: --> [2:OK]
Jul 28 13:37:18.89: [ 706]: <-- [9:AT+FTH=3\r]
Jul 28 13:37:19.41: [ 706]: --> [7:CONNECT]
Jul 28 13:37:19.41: [ 706]: <-- data [3]
Jul 28 13:37:19.41: [ 706]: <-- data [2]
Jul 28 13:37:19.52: [ 706]: --> [2:OK]
Jul 28 13:37:19.52: [ 706]: RECV send CRP (command repeat)
Jul 28 13:37:19.52: [ 706]: <-- [9:AT+FRH=3\r]
Jul 28 13:37:19.53: [ 706]: --> [7:CONNECT]
Jul 28 13:37:29.54: [ 706]: <-- data [1]
Jul 28 13:37:29.55: [ 706]: --> [2:OK]
Jul 28 13:37:29.55: [ 706]: RECV FAX: RSPREC invalid response received
Jul 28 13:37:29.55: [ 706]: RECV FAX: end
Jul 28 13:37:29.55: [ 706]: RSPREC invalid response received
Jul 28 13:37:29.55: [ 706]: SESSION END
Re: hylefax не принимает факсы
Добавлено: 2008-07-28 15:31:35
Vel
Блин всё начинается с лабуды
как с этим бороться? в каком месте у него кадр маленький
Re: hylefax не принимает факсы
Добавлено: 2008-07-28 15:55:59
Alex Keda
хуле-факс
Re: hylefax не принимает факсы
Добавлено: 2008-07-28 17:05:20
Vel
а мне ни фига не смешно, так не по кайфу, когда невозможно объяснить что лучше юзать железку, нежеле этим порно заниматься
Re: hylefax не принимает факсы
Добавлено: 2008-07-28 18:50:25
Alex Keda
что-то ты не так делаешь...
у меня не заводилось тока с неподдерживаемыми модемами....
=======
конфигурь по новой.
Re: hylefax не принимает факсы
Добавлено: 2008-07-28 22:11:01
Vel
Да вот именно, что тут с полупинка всё заводиться должно, вообщем мои действия:
Взял железку волосатого века ZyXel OMNI 56K, опросил, работает, присвоил значение нулевого регистра равному единице, т.е. снимать трубку после первого гудка:
Код: Выделить всё
# cu -l /dev/cuad0
Connected
ats0=1
OK
ats0?
001
Затем установил из портов hylafax, ghostscript за собой сам вытянул, /usr/local/sbin/faxsetup отработал, экстраординарного я ничего не указывал, указал устройство cuad0, завтра конфиг выложу. Затем поправил /etc/ttys:
Код: Выделить всё
cuad0 "/usr/local/sbin/faxgetty" dialup on secure
всё бы должно работать, но не тут-то было
Re: hylefax не принимает факсы
Добавлено: 2008-07-28 23:50:11
Alex Keda
а под вендой - этот момед факсы принимает?
Re: hylefax не принимает факсы
Добавлено: 2008-07-29 9:47:23
Vel
Фак, только что попробовал по мастдой на VentaZVoice и отправляет и принимает факсы.
Собственно там в VentaZvoice есть настройка размера кадра, может в этом вся фитча, он же мне говорит, что слишком маленький размер кадра - 3байта, а где его указать в hylafax я не знаю. Да по-моему такой опции и нету
Re: hylefax не принимает факсы
Добавлено: 2008-07-29 9:51:35
Alex Keda
сноси прогу, сноси ошмётки в /var/....
ставь и конфигурь по новой.
либо модем не поддерживается, либо.... х.з...
Re: hylefax не принимает факсы
Добавлено: 2008-07-29 9:52:56
Vel
да я уже 3-ий раз виртуалку сношу.
размер кадра HDLC в VentaZVoice указан 256 байт
Re: hylefax не принимает факсы
Добавлено: 2008-07-29 9:57:23
Vel
вот кстати мой /var/spool/hylafax/etc/config.cuad0:
Код: Выделить всё
CountryCode: 7
AreaCode: 495
FAXNumber: 777
LongDistancePrefix: 1
InternationalPrefix: 011
DialStringRules: etc/dialrules
ServerTracing: 1
SessionTracing: 11
RecvFileMode: 0600
LogFileMode: 0600
DeviceMode: 0600
RingsBeforeAnswer: 1
SpeakerVolume: on
GettyArgs: "-h %l dx_%s"
LocalIdentifier: "NothingSetup"
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "From %%l|%c|Page %%P of %%T"
MaxRecvPages: 25
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType: Class1 # use this to supply a hint
#ModemRate: 19200 # rate for DCE-DTE communication
#ModemFlowControl: xonxoff # XON/XOFF flow control assumed
#
#ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem
#ModemSetupDCDCmd: AT&C1 # setup so DCD follows carrier
#GettyArgs: "-h %l dx_%s" # modem must auto-detect fax/data
#
# We can append the "@" symbol to the dial string so that
# the modem will wait 5 seconds before attempting to connect
# and return result codes that distinguish between no carrier
# and no answer. This makes it possible to avoid problems with
# repeatedly dialing a number that doesn't have a fax machine
# (kudos to Stuart Lynne for this trick.)
#
# NB: If you need to prefix phone numbers to get through a PBX,
# put it in the ModemDialCmd; e.g. "DT9%s@".
#
#ModemDialCmd: ATDT%s # T for tone dialing
#
# Other possible configuration stuff. The default strings are
# shown below. Only those that are different from the defaults
# need to be included in the configuration file.
#
#ModemResetCmds: "" # stuff to do when modem is reset
#ModemAnswerCmd: ATA # use this to answer phone
#ModemNoFlowCmd: AT&K # disable flow control cmd
#ModemHardFlowCmd: AT&K3 # hardware flow control cmd
#ModemSoftFlowCmd: AT&K4 # software flow control cmd
#ModemNoAutoAnswerCmd: ATS0=0 # disable auto-answer
#
# Set modem speaker volume commands: OFF QUIET LOW MEDIUM HIGH.
# Note that we both turn the speaker on/off and set volume.
#
#ModemSetVolumeCmd: "ATM0 ATL0M1 ATL1M1 ATL2M1 ATL3M1"
#ModemEchoOffCmd: ATE0 # disable command echo
#ModemVerboseResultsCmd: ATV1 # enable verbose command results
#ModemResultCodesCmd: ATQ0 # enable result codes
#ModemOnHookCmd: ATH0 # place phone on hook (hangup)
#ModemSoftResetCmd: ATZ # do soft reset of modem
#ModemSoftResetCmdDelay: 3000 # pause after soft reset
#ModemWaitTimeCmd: ATS7=60 # wait 60 seconds for carrier
#ModemCommaPauseTimeCmd: ATS8=2 # comma pause time is 2 seconds
#ModemRecvFillOrder: LSB2MSB # bit order of received facsimile
#ModemSendFillOrder: LSB2MSB # bit order modem expects for transmit
#
Class1Cmd: AT+FCLASS=1 # command to enter class 1
Class1PPMWaitCmd: AT+FTS=7 # command to stop and wait before PPM
Class1TCFWaitCmd: AT+FTS=7 # command to stop and wait before TCF
Class1EOPWaitCmd: AT+FTS=9 # command to stop and wait before EOP
Class1SwitchingCmd: AT+FRS=7 # silence between HDLC recv and trans
Class1RecvAbortOK: 200 # wait 200ms for abort response
Class1FrameOverhead: 4 # 4 byte overhead in recvd HDLC frames
Class1RecvIdentTimer: 40000 # 35+5secs waiting for ident frames
Class1TCFMaxNonZero: 10 # max 10% of data may be non-zero
Class1TCFMinRun: 1000 # min run is 2/3rds of TCF duration
Re: hylefax не принимает факсы
Добавлено: 2008-07-29 10:29:16
Alex Keda
так.
идите нахрен с вашими виртуалками.
о таком надо сразу предупреждать.
Re: hylefax не принимает факсы
Добавлено: 2008-07-29 10:37:18
Vel
ну а в чём дело то? VMWare Workstation, COM порт я прикрутил физический виртуалке, с виртуалки и модем опрашивал.
А что такое?
Re: hylefax не принимает факсы
Добавлено: 2008-07-29 10:53:25
Alex Keda
ничего.
90% людей обратившихся с проблемами настрйоки чего угодно на виртуалке решили свои проблемы сами, переставив всё на реальную машину
Re: hylefax не принимает факсы
Добавлено: 2008-07-29 10:58:36
Fastman
Подтверждаю... в вмвари просто отвратно работает все что связанно с COM и USB портами...
Был опыт с попыткой прикрутить софт который работает по RS485 на виртуалке.. на обычном
компе конвертор RS232<->RS485 работает.. на виртуалке - нет.