Страница 4 из 4
Re: Аппаратный RAID
Добавлено: 2009-11-09 23:24:04
J.Korvin
Код: Выделить всё
MegaCli -PDList -aALL
Adapter #0
Enclosure Device ID: 8
Slot Number: 0
Device Id: 0
Sequence Number: 1
Media Error Count: 0
Other Error Count: 0
Predictive Failure Count: 0
Last Predictive Failure Event Seq Number: 0
PD Type: SATA
Raw Size: 465.761 GB [0x3a386030 Sectors]
Non Coerced Size: 465.261 GB [0x3a286030 Sectors]
Coerced Size: 465.25 GB [0x3a280000 Sectors]
Firmware state: Unconfigured(good), Spun Up
SAS Address(0): 0x1221000000000000
Connected Port Number: 0
Inquiry Data: ATA ST3500320NS SN05 9QM79FNY
FDE Capable: Not Capable
FDE Enable: Disable
Secured: Unsecured
Locked: Unlocked
Foreign State: Foreign
Foreign Secure: Drive is not secured by a foreign lock key
Device Speed: Unknown
Link Speed: Unknown
Media Type: Hard Disk Device
Enclosure Device ID: 8
Slot Number: 1
Device Id: 1
Sequence Number: 2
Media Error Count: 0
Other Error Count: 0
Predictive Failure Count: 0
Last Predictive Failure Event Seq Number: 0
PD Type: SATA
Raw Size: 465.761 GB [0x3a386030 Sectors]
Non Coerced Size: 465.261 GB [0x3a286030 Sectors]
Coerced Size: 465.25 GB [0x3a280000 Sectors]
Firmware state: Online
SAS Address(0): 0x1221000001000000
Connected Port Number: 1
Inquiry Data: ATA ST3500320NS SN06 9QMBS11T
FDE Capable: Not Capable
FDE Enable: Disable
Secured: Unsecured
Locked: Unlocked
Foreign State: None
Device Speed: Unknown
Link Speed: Unknown
Media Type: Hard Disk Device
Enclosure Device ID: 8
Slot Number: 2
Device Id: 2
Sequence Number: 2
Media Error Count: 0
Other Error Count: 0
Predictive Failure Count: 0
Last Predictive Failure Event Seq Number: 0
PD Type: SATA
Raw Size: 465.761 GB [0x3a386030 Sectors]
Non Coerced Size: 465.261 GB [0x3a286030 Sectors]
Coerced Size: 465.25 GB [0x3a280000 Sectors]
Firmware state: Online
SAS Address(0): 0x1221000002000000
Connected Port Number: 2
Inquiry Data: ATA ST3500320NS SN06 9QMBRACS
FDE Capable: Not Capable
FDE Enable: Disable
Secured: Unsecured
Locked: Unlocked
Foreign State: None
Device Speed: Unknown
Link Speed: Unknown
Media Type: Hard Disk Device
Enclosure Device ID: 8
Slot Number: 3
Device Id: 3
Sequence Number: 2
Media Error Count: 0
Other Error Count: 0
Predictive Failure Count: 0
Last Predictive Failure Event Seq Number: 0
PD Type: SATA
Raw Size: 465.761 GB [0x3a386030 Sectors]
Non Coerced Size: 465.261 GB [0x3a286030 Sectors]
Coerced Size: 465.25 GB [0x3a280000 Sectors]
Firmware state: Online
SAS Address(0): 0x1221000003000000
Connected Port Number: 3
Inquiry Data: ATA ST3500320NS SN06 9QMBRB16
FDE Capable: Not Capable
FDE Enable: Disable
Secured: Unsecured
Locked: Unlocked
Foreign State: None
Device Speed: Unknown
Link Speed: Unknown
Media Type: Hard Disk Device
Re: Аппаратный RAID
Добавлено: 2010-04-18 14:25:02
Overseer
подскажите плиз, как натравить aaccli или arcconf на этого зверя:
Код: Выделить всё
# dmesg | grep -i RAID
asr0: <Adaptec Caching SCSI RAID> mem 0xd4000000-0xd5ffffff irq 19 at device 11.0 on pci0
da0: <ADAPTEC RAID-1 380E> Fixed Direct Access SCSI-2 device
asr0: <Adaptec Caching SCSI RAID> mem 0xd4000000-0xd5ffffff irq 19 at device 11.0 on pci0
da0: <ADAPTEC RAID-1 380E> Fixed Direct Access SCSI-2 device
Код: Выделить всё
# arcconf GETCONFIG 0
Controllers found: 0
Invalid controller number.
FreeBSD 6.4
Re: Аппаратный RAID
Добавлено: 2010-04-21 13:46:06
weec
разбираюсь с утилитой arcconf
на данный момент имеется массив из 6 дисков в RAID 10
1 из дисков в состояние Failed, а массив в состоянии Degraded
тушу диск, затем меняю его состояние на READY, после этого он виден как Online, вот только процессa rebuild не было, а массив так же остался в Degraded
довольно странно это
запускаю инициализацию, которая, кстати, требует чтобы диск был в состоянии READY
инициализация диска включает процесс rebuild
и только по окончании rebuild процесса я вижу, что массив сменил статус на Optimal
на мой взгляд у LSI MegaCli более удобная и информативная
Re: Аппаратный RAID
Добавлено: 2011-01-13 9:31:48
Alex Keda
костылик, вот, в крон написал...
Код: Выделить всё
srv0# cat /root/scripts/work/check.disks.status.sh
#!/bin/sh
# AMI SCSI controllers
if test -e /dev/amr0
then
amrstat -g
fi
# 3 ware 9500 series
if test -e /dev/twa0
then
tw_cli /c0 show
fi
# 3ware 8006 series
if test -e /dev/twe0
then
tw_cli /c0 show
fi
# LSI SCSI controllers
if test -e /dev/mpt0
then
mptutil show volumes
mptutil show drives
fi
srv0#
Re: Аппаратный RAID
Добавлено: 2011-07-01 12:21:28
taric
Добрый день!
Разбираюсь тут с Adaptec 5405, возникло пару вопросов:
1. На данный момент есть 2 диска собранные в RAID1. Необходимо добавить в систему еще один винт, но не в рейд а так, такое возможно или нужно добавлять 2 (так как рейд1) и расширять масив?
2. Если возможно добавить просто диск, то это делается через
?
Вот что есть на данный момент:
Код: Выделить всё
arcconf GETCONFIG 1 AL
Controllers found: 1
----------------------------------------------------------------------
Controller information
----------------------------------------------------------------------
Controller Status : Optimal
Channel description : SAS/SATA
Controller Model : Adaptec 5405
Controller Serial Number : 0D06114C01E
Physical Slot : 5
Temperature : 55 C/ 131 F (Normal)
Installed memory : 256 MB
Copyback : Disabled
Background consistency check : Disabled
Automatic Failover : Enabled
Global task priority : High
Performance Mode : Default/Dynamic
Stayawake period : Disabled
Spinup limit internal drives : 0
Spinup limit external drives : 0
Defunct disk drive count : 0
Logical devices/Failed/Degraded : 1/0/0
SSDs assigned to MaxIQ Cache pool : 0
Maximum SSDs allowed in MaxIQ Cache pool : 8
MaxIQ Read Cache Pool Size : 0.000 GB
MaxIQ cache fetch rate : 0
MaxIQ Cache Read, Write Balance Factor : 3,1
NCQ status : Enabled
Statistics data collection mode : Enabled
--------------------------------------------------------
Controller Version Information
--------------------------------------------------------
BIOS : 5.2-0 (17899)
Firmware : 5.2-0 (17899)
Driver : 2.1-9 (1)
Boot Flash : 5.2-0 (17899)
--------------------------------------------------------
Controller Battery Information
--------------------------------------------------------
Status : Not Installed
----------------------------------------------------------------------
Logical device information
----------------------------------------------------------------------
Logical device number 0
Logical device name : rd1
RAID level : 1
Status of logical device : Optimal
Size : 953334 MB
Read-cache mode : Enabled
MaxIQ preferred cache setting : Enabled
MaxIQ cache setting : Disabled
Write-cache mode : Enabled (write-back)
Write-cache setting : Enabled (write-back)
Partitioned : Yes
Protected by Hot-Spare : No
Bootable : Yes
Failed stripes : No
Power settings : Disabled
--------------------------------------------------------
Logical device segment information
--------------------------------------------------------
Segment 0 : Present (0,0) 9WK05LQ1
Segment 1 : Present (0,1) 9WK09YSW
----------------------------------------------------------------------
Physical Device information
----------------------------------------------------------------------
Device #0
Device is a Hard drive
State : Online
Supported : Yes
Transfer Speed : SATA 3.0 Gb/s
Reported Channel,Device(T:L) : 0,0(0:0)
Reported Location : Connector 0, Device 0
Vendor :
Model : ST31000524NS
Firmware : SN11
Serial number : 9WK05LQ1
Size : 953869 MB
Write Cache : Enabled (write-back)
FRU : None
S.M.A.R.T. : No
S.M.A.R.T. warnings : 0
Power State : Full rpm
Supported Power States : Full rpm,Powered off
SSD : No
MaxIQ Cache Capable : No
MaxIQ Cache Assigned : No
NCQ status : Enabled
Device #1
Device is a Hard drive
State : Online
Supported : Yes
Transfer Speed : SATA 3.0 Gb/s
Reported Channel,Device(T:L) : 0,1(1:0)
Reported Location : Connector 0, Device 1
Vendor :
Model : ST31000524NS
Firmware : SN11
Serial number : 9WK09YSW
Size : 953869 MB
Write Cache : Enabled (write-back)
FRU : None
S.M.A.R.T. : No
S.M.A.R.T. warnings : 0
Power State : Full rpm
Supported Power States : Full rpm,Powered off
SSD : No
MaxIQ Cache Capable : No
MaxIQ Cache Assigned : No
NCQ status : Enabled
Device #2
Device is a Hard drive
State : Ready
Supported : Yes
Transfer Speed : SATA 3.0 Gb/s
Reported Channel,Device(T:L) : 0,2(2:0)
Reported Location : Connector 0, Device 2
Vendor :
Model : ST3500514NS
Firmware : SN12
Serial number : 9WJ0X27N
Size : 476940 MB
Write Cache : Enabled (write-back)
FRU : None
S.M.A.R.T. : No
S.M.A.R.T. warnings : 0
Power State : Full rpm
Supported Power States : Full rpm,Powered off
SSD : No
MaxIQ Cache Capable : No
MaxIQ Cache Assigned : No
NCQ status : Enabled
Command completed successfully.
Re: Аппаратный RAID
Добавлено: 2011-07-01 15:08:17
taric
Сделал вот как:
Код: Выделить всё
#arcconf CREATE 1 JBOD 0 2
Controllers found: 1
WARNING: The selected controller supports JBODs, but the currently
installed driver does not. You may not see JBOD disks in your
operating system until you upgrade your driver.
Created JBOD: 0,2
Command completed successfully.
Но в как видите ругается на драйвер..... пока в тупике. Кто-то сталкивался с таким?
Re: Аппаратный RAID
Добавлено: 2011-07-01 16:40:43
taric
Re: Аппаратный RAID
Добавлено: 2011-10-17 9:58:11
ddenia
Аппаратный RAID
Добавлено: 2016-06-30 9:55:40
dymx
Столкнулся со странной проблемой, не запускается arcconf
Код: Выделить всё
cat /var/run/dmesg.boot | grep RAID
aac0: <Adaptec RAID 3405> mem 0xe1000000-0xe11fffff irq 18 at device 14.0 on pci2
Код: Выделить всё
uname -a
FreeBSD hostname 9.3-RELEASE-p33 FreeBSD 9.3-RELEASE-p33 #0: Wed Jan 13 17:55:39 UTC 2016
Код: Выделить всё
arcconf GETSTATUS 1
Segmentation fault: 11 (core dumped)
На точно такой же FreeBSD 9.3 с контроллером Adaptec RAID 2405 всё нормально. Куда копать?
И еще такой вопрос, правильно ли будет считывать состояние smart (с помощью smartctl) за контроллером в качестве диагностики?
Аппаратный RAID
Добавлено: 2016-06-30 17:12:56
Neus
А эта версия утилиты поддерживает этот контроллер?
Аппаратный RAID
Добавлено: 2016-06-30 18:33:29
dymx
Проблема решилась сносом версии 1.6 (та что из портов) и копированием файла из архива
Код: Выделить всё
http://download.adaptec.com/raid/storage_manager/asm_freebsd_x64_v6_50_18579.tgz
Причем там внутри файл для версии FreeBSD 8, всё ок.