forum.lissyara.su

Если есть силы бежать – кто поверит, что нет сил драться?!
https://forum.lissyara.su/

Сом порты :(

https://forum.lissyara.su/viewtopic.php?f=5&t=15495

Страница 1 из 1

Сом порты :(

Добавлено: 2009-02-17 16:40:02
Vitaliy
Господа подскажите как быть...
Есть система на freebsd 7.1 поставил 2 платки MosChip MCS9835 2 ком порта +1 паралельный
С первого раза система их не нашла, пришлось подправить sys/dev/sio/sio_pci.c согласно http://lists.freebsd.org/pipermail/free ... 23163.html, пересобрал ядро, установил плата стала определять как MosChip Semiconductors (Was: Netmos Technology) - Nm9835 Parallel/Serial Port Adapter НО почему то работает только 1 сом порт, на каждой плате.

Подскажите как завести 2 порт на плате ?... Голова уже рвется (

Re: Сом порты :(

Добавлено: 2009-02-17 16:48:26
paradox

Код: Выделить всё

pciconf -lvc

Re: Сом порты :(

Добавлено: 2009-02-17 17:24:22
Гость
gateway# pciconf -lvc

Код: Выделить всё

hostb0@pci0:0:0:0:      class=0x060000 card=0x81ea1043 chip=0x29a08086 rev=0x02 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = '?(82P965) Intel P965/G965 Processor to I/O Controller'
    class      = bridge
    subclass   = HOST-PCI
    cap 09[e0] = vendor (length 9) Intel cap 0 version 1
pcib1@pci0:0:1:0:       class=0x060400 card=0x00008086 chip=0x29a18086 rev=0x02 hdr=0x01
    vendor     = 'Intel Corporation'
    device     = '?(82Q965, 82G965, 82P965) Intel P965/G965 PCI Express Root Port'
    class      = bridge
    subclass   = PCI-PCI
    cap 0d[88] = PCI Bridge card=0x00008086
    cap 01[80] = powerspec 3  supports D0 D3  current D0
    cap 05[90] = MSI supports 1 message
    cap 10[a0] = PCI-Express 1 root port
uhci0@pci0:0:26:0:      class=0x0c0300 card=0x81ec1043 chip=0x28348086 rev=0x02 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = '82801H (ICH8 Family) USB UHCI'
    class      = serial bus
    subclass   = USB
uhci1@pci0:0:26:1:      class=0x0c0300 card=0x81ec1043 chip=0x28358086 rev=0x02 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = '82801H (ICH8 Family) USB UHCI'
    class      = serial bus
    subclass   = USB
ehci0@pci0:0:26:7:      class=0x0c0320 card=0x81ec1043 chip=0x283a8086 rev=0x02 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = '81EC1043 (?) ICH8 Enhanced USB2 Enhanced Host Controller'
    class      = serial bus
    subclass   = USB
    cap 01[50] = powerspec 2  supports D0 D3  current D0
    cap 0a[58] = EHCI Debug Port at offset 0xa0 in map 0x14
none0@pci0:0:27:0:      class=0x040300 card=0x81ec1043 chip=0x284b8086 rev=0x02 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = '82801H &SUBSYS_81EC1043&REV_02\3&11583659&0&D8'
    class      = multimedia
    cap 01[50] = powerspec 2  supports D0 D3  current D0
    cap 05[60] = MSI supports 1 message, 64 bit
    cap 10[70] = PCI-Express 1 type 0
pcib2@pci0:0:28:0:      class=0x060400 card=0x81ec1043 chip=0x283f8086 rev=0x02 hdr=0x01
    vendor     = 'Intel Corporation'
    device     = '82801H (ICH8 Family) PCIe Port 1'
    class      = bridge
    subclass   = PCI-PCI
    cap 10[40] = PCI-Express 1 root port
    cap 05[80] = MSI supports 1 message
    cap 0d[90] = PCI Bridge card=0x81ec1043
    cap 01[a0] = powerspec 2  supports D0 D3  current D0
pcib3@pci0:0:28:3:      class=0x060400 card=0x81ec1043 chip=0x28458086 rev=0x02 hdr=0x01
    vendor     = 'Intel Corporation'
    device     = '82801H (ICH8 Family) PCIe Port 4'
    class      = bridge
    subclass   = PCI-PCI
    cap 10[40] = PCI-Express 1 root port
    cap 05[80] = MSI supports 1 message
    cap 0d[90] = PCI Bridge card=0x81ec1043
    cap 01[a0] = powerspec 2  supports D0 D3  current D0
pcib4@pci0:0:28:4:      class=0x060400 card=0x81ec1043 chip=0x28478086 rev=0x02 hdr=0x01
    vendor     = 'Intel Corporation'
    device     = '82801H (ICH8 Family) PCIe Port 5'
    class      = bridge
    subclass   = PCI-PCI
    cap 10[40] = PCI-Express 1 root port
    cap 05[80] = MSI supports 1 message
    cap 0d[90] = PCI Bridge card=0x81ec1043
    cap 01[a0] = powerspec 2  supports D0 D3  current D0
uhci2@pci0:0:29:0:      class=0x0c0300 card=0x81ec1043 chip=0x28308086 rev=0x02 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = '82801H (ICH8 Family) USB UHCI'
    class      = serial bus
    subclass   = USB
uhci3@pci0:0:29:1:      class=0x0c0300 card=0x81ec1043 chip=0x28318086 rev=0x02 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = '82801H (ICH8 Family) USB UHCI'
    class      = serial bus
    subclass   = USB
uhci4@pci0:0:29:2:      class=0x0c0300 card=0x81ec1043 chip=0x28328086 rev=0x02 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = '82801H (ICH8 Family) USB UHCI'
    class      = serial bus
    subclass   = USB
ehci1@pci0:0:29:7:      class=0x0c0320 card=0x81ec1043 chip=0x28368086 rev=0x02 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = '82801H (ICH8 Family) USB2 EHCI'
    class      = serial bus
    subclass   = USB
    cap 01[50] = powerspec 2  supports D0 D3  current D0
    cap 0a[58] = EHCI Debug Port at offset 0xa0 in map 0x14
pcib5@pci0:0:30:0:      class=0x060401 card=0x81ec1043 chip=0x244e8086 rev=0xf2 hdr=0x01
    vendor     = 'Intel Corporation'
    device     = '82801 Family (ICH2/3/4/4/5/5/6/7/8/9,63xxESB) Hub Interface to PCI Bridge'
    class      = bridge
    subclass   = PCI-PCI
    cap 0d[50] = PCI Bridge card=0x81ec1043
isab0@pci0:0:31:0:      class=0x060100 card=0x81ec1043 chip=0x28108086 rev=0x02 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = '82801HB/HR (ICH8/R) LPC Interface Controller'
    class      = bridge
    subclass   = PCI-ISA
    cap 09[e0] = vendor (length 12) Intel cap 1 version 0
                 features: SATA RAID-5, 4 PCI-e x1 slots, SATA RAID-0/1/10
atapci2@pci0:0:31:2:    class=0x01018f card=0x81ec1043 chip=0x28208086 rev=0x02 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = 'ICH8 4 port Serial ATA Storage Controller ?'
    class      = mass storage
    subclass   = ATA
    cap 01[70] = powerspec 3  supports D0 D3  current D0
none1@pci0:0:31:3:      class=0x0c0500 card=0x81ec1043 chip=0x283e8086 rev=0x02 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = '82801H (ICH8 Family) SMBus Controller'
    class      = serial bus
    subclass   = SMBus
atapci3@pci0:0:31:5:    class=0x010185 card=0x81ec1043 chip=0x28258086 rev=0x02 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = '? ICH8 2 port Serial ATA Storage Controller'
    class      = mass storage
    subclass   = ATA
    cap 01[70] = powerspec 3  supports D0 D3  current D0
vgapci0@pci0:1:0:0:     class=0x030000 card=0x00000000 chip=0x039310de rev=0xa1 hdr=0x00
    vendor     = 'Nvidia Corp'
    device     = 'GeForce 7300 GT'
    class      = display
    subclass   = VGA
    cap 01[60] = powerspec 2  supports D0 D3  current D0
    cap 05[68] = MSI supports 1 message, 64 bit
    cap 10[78] = PCI-Express 1 endpoint
re0@pci0:3:0:0: class=0x020000 card=0x81681043 chip=0x816810ec rev=0x01 hdr=0x00
    vendor     = 'Realtek Semiconductor'
    device     = 'RTL8168/8111 PCI-E Gigabit Ethernet NIC'
    class      = network
    subclass   = ethernet
    cap 01[40] = powerspec 2  supports D0 D1 D2 D3  current D0
    cap 03[48] = VPD
    cap 05[50] = MSI supports 2 messages, 64 bit
    cap 10[60] = PCI-Express 1 endpoint
    cap 09[84] = vendor (length 76)
atapci0@pci0:2:0:0:     class=0x010601 card=0x81e41043 chip=0x2363197b rev=0x02 hdr=0x00
    vendor     = 'JMicron Technology Corp'
    device     = 'JMB36X PCIe-to-SATA-300/IDE RAID Controller'
    class      = mass storage
    cap 01[68] = powerspec 2  supports D0 D3  current D0
    cap 10[50] = PCI-Express 1 legacy endpoint IRQ 0
atapci1@pci0:2:0:1:     class=0x010185 card=0x81e41043 chip=0x2363197b rev=0x02 hdr=0x00
    vendor     = 'JMicron Technology Corp'
    device     = 'JMB36X PCIe-to-SATA-300/IDE RAID Controller'
    class      = mass storage
    subclass   = ATA
    cap 01[68] = powerspec 2  supports D0 D3  current D0
sio4@pci0:5:0:0:        class=0x078000 card=0x00121000 chip=0x98359710 rev=0x01 hdr=0x00
    vendor     = 'MosChip Semiconductors (Was: Netmos Technology)'
    device     = 'Nm9835 Parallel/Serial Port Adapter'
    class      = simple comms
sio5@pci0:5:1:0:        class=0x078000 card=0x00121000 chip=0x98359710 rev=0x01 hdr=0x00
    vendor     = 'MosChip Semiconductors (Was: Netmos Technology)'
    device     = 'Nm9835 Parallel/Serial Port Adapter'
    class      = simple comms
dc0@pci0:5:2:0: class=0x020000 card=0x50323030 chip=0x91021282 rev=0x31 hdr=0x00
    vendor     = 'Davicom Semiconductor Inc.'
    device     = 'DM9102/A/AF 10/100 Mbps Fast Ethernet Controller'
    class      = network
    subclass   = ethernet
    cap 01[50] = powerspec 1  supports D0 D3  current D0

Re: Сом порты :(

Добавлено: 2009-02-17 17:36:25
paradox

Код: Выделить всё

dmesg -a
ls -l /dev/
и рассказывайте как что и чем проверяете

Re: Сом порты :(

Добавлено: 2009-02-17 17:44:52
Vitaliy
gateway# ls /dev/

acd0 ad12s1 ata cuad4 fd lpt0.ctl nfs4 ptyp4 ttyd4.init ttyv0 ttyvb usb4
acpi ad12s1c atkbd0 cuad4.init fido mdctl nfslock ptyp5 ttyd4.lock ttyv1 ttyvc usb5
ad10 ad12s1d audit cuad4.lock geom.ctl mem null random ttyd5 ttyv2 ttyvd usb6
ad10s1 ad14 bpf0 cuad5 io net pci stderr ttyd5.init ttyv3 ttyve xpt0
ad10s1a ad14s1 bpsm0 cuad5.init kbd0 net1 pf stdin ttyd5.lock ttyv4 ttyvf zero
ad10s1b ad14s1c console cuad5.lock kbd1 net2 ppi0 stdout ttyp0 ttyv5 urandom
ad10s1c ad14s1d consolectl dcons kbdmux0 net3 psm0 sysmouse ttyp1 ttyv6 usb
ad10s1d ad16 ctty devctl klog net4 ptyp0 ttyd0 ttyp2 ttyv7 usb0
ad10s1e ad16s1 cuad0 devstat kmem net5 ptyp1 ttyd0.init ttyp3 ttyv8 usb1
ad10s1f ad16s1c cuad0.init dgdb log net6 ptyp2 ttyd0.lock ttyp4 ttyv9 usb2
ad12 ad16s1d cuad0.lock dumpdev lpt0 network ptyp3 ttyd4 ttyp5 ttyva usb3


проверяю модемом

cu -l /dev/ttyd4 и cu -l /dev/ttyd5, последний вариант заработал когда модем переставил в другую плату

Re: Сом порты :(

Добавлено: 2009-02-17 17:53:17
Vitaliy
кусочек dmesg

Код: Выделить всё


pcib5: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci5: <ACPI PCI bus> on pcib5
sio0: configured irq 21 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: configured irq 21 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: <MosChip MCS9835 PCI Dual UART> port 0xbc00-0xbc07,0xb880-0xb887,0xb800-0xb807,0xb480-0xb487,0xb400-0xb407,0xb080-0xb08f irq 21 at device 0.0 on pci5
sio0: moving to sio4
sio4: type 16550A
sio4: [FILTER]
sio0: configured irq 22 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: configured irq 22 not in bitmap of probed irqs 0
sio0: port may not be enabled
can't re-use a leaf (%desc)!
can't re-use a leaf (%driver)!
can't re-use a leaf (%location)!
can't re-use a leaf (%pnpinfo)!
can't re-use a leaf (%parent)!
sio0: <MosChip MCS9835 PCI Dual UART> port 0xb000-0xb007,0xac00-0xac07,0xa880-0xa887,0xa800-0xa807,0xa480-0xa487,0xa400-0xa40f irq 22 at device 1.0 on pci5
sio0: moving to sio5
sio5: type 16550A
sio5: [FILTER]
dc0: <Davicom DM9102A 10/100BaseTX> port 0xa000-0xa0ff mem 0xfeaffc00-0xfeaffcff irq 23 at device 2.0 on pci5
miibus1: <MII bus> on dc0
amphy0: <DM9102 10/100 media interface> PHY 1 on miibus1
amphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
dc0: Ethernet address: 00:80:ad:0a:01:81
dc0: [ITHREAD]
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci2: <Intel ICH8 SATA300 controller> port 0xec00-0xec07,0xe880-0xe883,0xe800-0xe807,0xe480-0xe483,0xe400-0xe40f,0xe080-0xe08f irq 19 at device 31.2 on pci0
atapci2: [ITHREAD]
ata5: <ATA channel 0> on atapci2
ata5: [ITHREAD]
ata6: <ATA channel 1> on atapci2
ata6: [ITHREAD]
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
atapci3: <Intel ICH8 SATA300 controller> port 0xd400-0xd407,0xd080-0xd083,0xd000-0xd007,0xcc00-0xcc03,0xc880-0xc88f,0xc800-0xc80f irq 19 at device 31.5 on pci0
atapci3: [ITHREAD]
ata7: <ATA channel 0> on atapci3
ata7: [ITHREAD]
ata8: <ATA channel 1> on atapci3
ata8: [ITHREAD]
acpi_button0: <Power Button> on acpi0
can't re-use a leaf (%desc)!
can't re-use a leaf (%driver)!
can't re-use a leaf (%location)!
can't re-use a leaf (%pnpinfo)!
can't re-use a leaf (%parent)!
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
sio0: [FILTER]
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]

Re: Сом порты :(

Добавлено: 2009-02-17 17:56:34
paradox
вроде модемы пожизни были /dev/cua*
а не tty

Re: Сом порты :(

Добавлено: 2009-02-17 17:57:28
paradox

Код: Выделить всё

sio0: configured irq 22 not in bitmap of probed irqs 0sio0: port may not be enabledsio0: configured irq 22 not in bitmap of probed irqs 0sio0: port may not be enabledcan't re-use a leaf (%desc)!can't re-use a leaf (%driver)!can't re-use a leaf (%location)!can't re-use a leaf (%pnpinfo)!can't re-use a leaf (%parent
что то там совсем не хорошо....

Re: Сом порты :(

Добавлено: 2009-02-17 18:03:59
Vitaliy
не суть важно, модем отвечал ... почему в системе ttyd0 ttyd4 ttyd5 (либо cua0 cua4 cua5) , где еще 2 порта они мне ой как нужны

Re: Сом порты :(

Добавлено: 2009-02-17 18:06:21
Гость
paradox писал(а):

Код: Выделить всё

sio0: configured irq 22 not in bitmap of probed irqs 0sio0: port may not be enabledsio0: configured irq 22 not in bitmap of probed irqs 0sio0: port may not be enabledcan't re-use a leaf (%desc)!can't re-use a leaf (%driver)!can't re-use a leaf (%location)!can't re-use a leaf (%pnpinfo)!can't re-use a leaf (%parent
что то там совсем не хорошо....

я это и сам видел, понимаю что что то не так, вот и спрашиваю на форуме потому что не догоняю темы :(

Re: Сом порты :(

Добавлено: 2009-02-17 18:14:24
Vitaliy
Кстати реализую сервак вот по этой статье http://www.lissyara.su/?id=1190 там ttyd0

Re: Сом порты :(

Добавлено: 2009-02-17 18:15:18
paradox
попробуй загрузиться без поддержки ACPI

покажешь/посмотришь dmesg -a
исчезли ошибки или нет

там какая то накладка в ресурсах как мне кажеться

вариантов можно рассматривать милион
он обновления железа - другую мать
до обновления биоса
а то и попытки поднять это чудо под виндной на этом же железе

как еще вариант попробовать в дрогум pci слоте

Re: Сом порты :(

Добавлено: 2009-02-17 18:20:33
Vitaliy
paradox писал(а): попробуй загрузиться без поддержки ACPI
покажешь/посмотришь dmesg -a
исчезли ошибки или нет
Это ладно, затра с утра можно будет пока никого не будет на работе
paradox писал(а): там какая то накладка в ресурсах как мне кажеться
вариантов можно рассматривать милион
он обновления железа - другую мать
до обновления биоса
а то и попытки поднять это чудо под виндной на этом же железе
Эт чет не прикалывает, тока позавчера систему поставил... до этого стояла 6,2
paradox писал(а): как еще вариант попробовать в дрогум pci слоте
все порты заняты из всего 3 шт, на 1 сетевуха в нет смотрящая , 2 платы с портами

Re: Сом порты :(

Добавлено: 2009-02-17 18:23:25
paradox
освобождаешь все порты и пробуешь
если что перетыкаешь в другие слоты

пока других мыслей нет....

Re: Сом порты :(

Добавлено: 2009-02-17 18:26:08
Vitaliy
А вот это http://forum.lissyara.su/viewtopic.php?f=5&p=63582 не та же проблема... ? :cz2:

Re: Сом порты :(

Добавлено: 2009-02-17 18:52:12
paradox
убирайте свой фикс
пересобирайте нормальное ядро
и загружайте puc девайс :smile:

Re: Сом порты :(

Добавлено: 2009-02-18 5:36:05
Vitaliy
ага.... значит вернул все обратно, собрал ядро с опцией puc платы находятся но !!!

Щас стоит 1 модем, в 1 плате на 1 порту. Пытался к нему подключиться
cu -l /dev/cuau0
cu -l /dev/cuau1
cu -l /dev/cuau2
cu -l /dev/cuau3
Никак не получилось %(


gateway# ll /dev/ | grep ttyu

Код: Выделить всё

crw-------  1 root  wheel       0,  43 Feb 18 10:27 ttyu0
crw-------  1 root  wheel       0,  44 Feb 18 09:46 ttyu0.init
crw-------  1 root  wheel       0,  45 Feb 18 09:46 ttyu0.lock
crw-------  1 root  wheel       0,  49 Feb 18 10:27 ttyu1
crw-------  1 root  wheel       0,  50 Feb 18 09:46 ttyu1.init
crw-------  1 root  wheel       0,  51 Feb 18 09:46 ttyu1.lock
crw-------  1 root  wheel       0,  58 Feb 18 10:27 ttyu2
crw-------  1 root  wheel       0,  59 Feb 18 09:46 ttyu2.init
crw-------  1 root  wheel       0,  60 Feb 18 09:46 ttyu2.lock
crw-------  1 root  wheel       0,  64 Feb 18 10:28 ttyu3
crw-------  1 root  wheel       0,  65 Feb 18 09:46 ttyu3.init
crw-------  1 root  wheel       0,  66 Feb 18 09:46 ttyu3.lock
пробую так
cu -l /dev/ttyu0
cu -l /dev/ttyu1
cu -l /dev/ttyu2
cu -l /dev/ttyu3

тож не работает (
dmesg

Код: Выделить всё


Copyright (c) 1992-2009 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 7.1-RELEASE #4: Wed Feb 18 09:23:26 IRKT 2009
    root@gateway:/usr/obj/usr/src/sys/GENERIC
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Core(TM)2 CPU          6400  @ 2.13GHz (2128.38-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x6f6  Stepping = 6
  Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Features2=0xe3bd<SSE3,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM>
  AMD Features=0x20100000<NX,LM>
  AMD Features2=0x1<LAHF>
  Cores per package: 2
real memory  = 2147090432 (2047 MB)
avail memory = 2091446272 (1994 MB)
ACPI APIC Table: <A M I  OEMAPIC >
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
 cpu0 (BSP): APIC ID:  0
 cpu1 (AP): APIC ID:  1
ioapic0 <Version 2.0> irqs 0-23 on motherboard
kbd1 at kbdmux0
ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
acpi0: <A M I OEMRSDT> on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
acpi0: reservation of 0, a0000 (3) failed
acpi0: reservation of 100000, 7ff00000 (3) failed
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
vgapci0: <VGA-compatible display> port 0x7c00-0x7c7f mem 0xfd000000-0xfdffffff,0xc0000000-0xcfffffff,0xfc000000-0xfcffffff irq 16 at device 0.0 on pci1
uhci0: <Intel 82801H (ICH8) USB controller USB-D> port 0xdc00-0xdc1f irq 16 at device 26.0 on pci0
uhci0: [GIANT-LOCKED]
uhci0: [ITHREAD]
usb0: <Intel 82801H (ICH8) USB controller USB-D> on uhci0
usb0: USB revision 1.0
uhub0: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801H (ICH8) USB controller USB-E> port 0xe000-0xe01f irq 17 at device 26.1 on pci0
uhci1: [GIANT-LOCKED]
uhci1: [ITHREAD]
usb1: <Intel 82801H (ICH8) USB controller USB-E> on uhci1
usb1: USB revision 1.0
uhub1: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1
uhub1: 2 ports with 2 removable, self powered
ehci0: <Intel 82801H (ICH8) USB 2.0 controller USB2-B> mem 0xfebffc00-0xfebfffff irq 18 at device 26.7 on pci0
ehci0: [GIANT-LOCKED]
ehci0: [ITHREAD]
usb2: EHCI version 1.0
usb2: companion controllers, 2 ports each: usb0 usb1
usb2: <Intel 82801H (ICH8) USB 2.0 controller USB2-B> on ehci0
usb2: USB revision 2.0
uhub2: <Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb2
uhub2: 4 ports with 4 removable, self powered
pci0: <multimedia> at device 27.0 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
pci4: <ACPI PCI bus> on pcib2
pcib3: <ACPI PCI-PCI bridge> irq 19 at device 28.3 on pci0
pci3: <ACPI PCI bus> on pcib3
re0: <RealTek 8168/8168B/8168C/8168CP/8168D/8111B/8111C/8111CP PCIe Gigabit Ethernet> port 0x9800-0x98ff mem 0xfe9ff000-0xfe9fffff irq 19 at device 0.0 on pci3
re0: turning off MSI enable bit.
re0: Chip rev. 0x38000000
re0: MAC rev. 0x00000000
miibus0: <MII bus> on re0
rgephy0: <RTL8169S/8110S/8211B media interface> PHY 1 on miibus0
rgephy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
re0: Ethernet address: 00:18:f3:51:e3:12
re0: [FILTER]
pcib4: <ACPI PCI-PCI bridge> irq 16 at device 28.4 on pci0
pci2: <ACPI PCI bus> on pcib4
atapci0: <JMicron AHCI controller> mem 0xfe8fe000-0xfe8fffff irq 16 at device 0.0 on pci2
atapci0: [ITHREAD]
atapci0: AHCI Version 01.00 controller with 2 ports detected
ata2: <ATA channel 0> on atapci0
ata2: [ITHREAD]
ata3: <ATA channel 1> on atapci0
ata3: [ITHREAD]
atapci1: <JMicron JMB363 UDMA133 controller> port 0x8c00-0x8c07,0x8880-0x8883,0x8800-0x8807,0x8480-0x8483,0x8400-0x840f at device 0.1 on pci2
atapci1: [ITHREAD]
ata4: <ATA channel 0> on atapci1
ata4: [ITHREAD]
uhci2: <Intel 82801H (ICH8) USB controller USB-A> port 0xd480-0xd49f irq 23 at device 29.0 on pci0
uhci2: [GIANT-LOCKED]
uhci2: [ITHREAD]
usb3: <Intel 82801H (ICH8) USB controller USB-A> on uhci2
usb3: USB revision 1.0
uhub3: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb3
uhub3: 2 ports with 2 removable, self powered
uhci3: <Intel 82801H (ICH8) USB controller USB-B> port 0xd800-0xd81f irq 19 at device 29.1 on pci0
uhci3: [GIANT-LOCKED]
uhci3: [ITHREAD]
usb4: <Intel 82801H (ICH8) USB controller USB-B> on uhci3
usb4: USB revision 1.0
uhub4: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb4
uhub4: 2 ports with 2 removable, self powered
uhci4: <Intel 82801H (ICH8) USB controller USB-C> port 0xd880-0xd89f irq 18 at device 29.2 on pci0
uhci4: [GIANT-LOCKED]
uhci4: [ITHREAD]
usb5: <Intel 82801H (ICH8) USB controller USB-C> on uhci4
usb5: USB revision 1.0
uhub5: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb5
uhub5: 2 ports with 2 removable, self powered
ehci1: <Intel 82801H (ICH8) USB 2.0 controller USB2-A> mem 0xfebff800-0xfebffbff irq 23 at device 29.7 on pci0
ehci1: [GIANT-LOCKED]
ehci1: [ITHREAD]
usb6: EHCI version 1.0
usb6: companion controllers, 2 ports each: usb3 usb4 usb5
usb6: <Intel 82801H (ICH8) USB 2.0 controller USB2-A> on ehci1
usb6: USB revision 2.0
uhub6: <Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb6
uhub6: 6 ports with 6 removable, self powered
pcib5: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci5: <ACPI PCI bus> on pcib5
puc0: <NetMos NM9835 Dual UART and 1284 Printer port> port 0xbc00-0xbc07,0xb880-0xb887,0xb800-0xb807,0xb480-0xb487,0xb400-0xb407,0xb080-0xb08f irq 21 at device 0.0 on pci5
puc0: [FILTER]
uart0: <Non-standard ns8250 class UART with FIFOs> on puc0
uart0: [FILTER]
uart1: <Non-standard ns8250 class UART with FIFOs> on puc0
uart1: [FILTER]
ppc0: <Parallel port> on puc0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
plip0: cannot reserve interrupt, failed.
lpt0: <Printer> on ppbus0
lpt0: Polled port
ppi0: <Parallel I/O> on ppbus0
puc1: <NetMos NM9835 Dual UART and 1284 Printer port> port 0xb000-0xb007,0xac00-0xac07,0xa880-0xa887,0xa800-0xa807,0xa480-0xa487,0xa400-0xa40f irq 22 at device 1.0 on pci5
puc1: [FILTER]
uart2: <Non-standard ns8250 class UART with FIFOs> on puc1
uart2: [FILTER]
uart3: <Non-standard ns8250 class UART with FIFOs> on puc1
uart3: [FILTER]
ppc1: <Parallel port> on puc1
ppc1: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
ppbus1: <Parallel port bus> on ppc1
plip1: cannot reserve interrupt, failed.
lpt1: <Printer> on ppbus1
lpt1: Polled port
ppi1: <Parallel I/O> on ppbus1
dc0: <Davicom DM9102A 10/100BaseTX> port 0xa000-0xa0ff mem 0xfeaffc00-0xfeaffcff irq 23 at device 2.0 on pci5
miibus1: <MII bus> on dc0
amphy0: <DM9102 10/100 media interface> PHY 1 on miibus1
amphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
dc0: Ethernet address: 00:80:ad:0a:01:81
dc0: [ITHREAD]
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci2: <Intel ICH8 SATA300 controller> port 0xec00-0xec07,0xe880-0xe883,0xe800-0xe807,0xe480-0xe483,0xe400-0xe40f,0xe080-0xe08f irq 19 at device 31.2 on pci0
atapci2: [ITHREAD]
ata5: <ATA channel 0> on atapci2
ata5: [ITHREAD]
ata6: <ATA channel 1> on atapci2
ata6: [ITHREAD]
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
atapci3: <Intel ICH8 SATA300 controller> port 0xd400-0xd407,0xd080-0xd083,0xd000-0xd007,0xcc00-0xcc03,0xc880-0xc88f,0xc800-0xc80f irq 19 at device 31.5 on pci0
atapci3: [ITHREAD]
ata7: <ATA channel 0> on atapci3
ata7: [ITHREAD]
ata8: <ATA channel 1> on atapci3
ata8: [ITHREAD]
acpi_button0: <Power Button> on acpi0
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
sio0: [FILTER]
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: [ITHREAD]
psm0: model NetMouse/NetScroll Optical, device ID 0
cpu0: <ACPI CPU> on acpi0
ACPI Warning (tbutils-0243): Incorrect checksum in table [SSDT] -  34, should be 3B [20070320]
ACPI Warning (tbutils-0243): Incorrect checksum in table [OEMB] -  90, should be 8B [20070320]
est0: <Enhanced SpeedStep Frequency Control> on cpu0
p4tcc0: <CPU Frequency Thermal Control> on cpu0
cpu1: <ACPI CPU> on acpi0
est1: <Enhanced SpeedStep Frequency Control> on cpu1
p4tcc1: <CPU Frequency Thermal Control> on cpu1
pmtimer0 on isa0
ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0
ata0: [ITHREAD]
ata1 at port 0x170-0x177,0x376 irq 15 on isa0
ata1: [ITHREAD]
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounters tick every 1.000 msec
acd0: DVDR <NEC DVD RW ND-2500A/1.06> at ata4-master UDMA33
ad10: 76319MB <Seagate ST380815AS 4.AAB> at ata5-master SATA300
ad12: 152627MB <Seagate ST3160815AS 4.AAB> at ata6-master SATA150
ad14: 238475MB <Seagate ST3250410AS 3.AAC> at ata7-master SATA150
ad16: 238475MB <Seagate ST3250410AS 3.AAC> at ata8-master SATA150
SMP: AP CPU #1 Launched!
Trying to mount root from ufs:/dev/ad10s1a
Loading configuration files.
kernel dumps on /dev/ad10s1b
Entropy harvesting:
 interrupts
 ethernet
 point_to_point
 kickstart

gateway# pciconf -lvc

Код: Выделить всё

hostb0@pci0:0:0:0:	class=0x060000 card=0x81ea1043 chip=0x29a08086 rev=0x02 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = '?(82P965) Intel P965/G965 Processor to I/O Controller'
    class      = bridge
    subclass   = HOST-PCI
    cap 09[e0] = vendor (length 9) Intel cap 0 version 1
pcib1@pci0:0:1:0:	class=0x060400 card=0x00008086 chip=0x29a18086 rev=0x02 hdr=0x01
    vendor     = 'Intel Corporation'
    device     = '?(82Q965, 82G965, 82P965) Intel P965/G965 PCI Express Root Port'
    class      = bridge
    subclass   = PCI-PCI
    cap 0d[88] = PCI Bridge card=0x00008086
    cap 01[80] = powerspec 3  supports D0 D3  current D0
    cap 05[90] = MSI supports 1 message 
    cap 10[a0] = PCI-Express 1 root port
uhci0@pci0:0:26:0:	class=0x0c0300 card=0x81ec1043 chip=0x28348086 rev=0x02 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = '82801H (ICH8 Family) USB UHCI'
    class      = serial bus
    subclass   = USB
uhci1@pci0:0:26:1:	class=0x0c0300 card=0x81ec1043 chip=0x28358086 rev=0x02 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = '82801H (ICH8 Family) USB UHCI'
    class      = serial bus
    subclass   = USB
ehci0@pci0:0:26:7:	class=0x0c0320 card=0x81ec1043 chip=0x283a8086 rev=0x02 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = '81EC1043 (?) ICH8 Enhanced USB2 Enhanced Host Controller'
    class      = serial bus
    subclass   = USB
    cap 01[50] = powerspec 2  supports D0 D3  current D0
    cap 0a[58] = EHCI Debug Port at offset 0xa0 in map 0x14
none0@pci0:0:27:0:	class=0x040300 card=0x81ec1043 chip=0x284b8086 rev=0x02 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = '82801H &SUBSYS_81EC1043&REV_02\3&11583659&0&D8'
    class      = multimedia
    cap 01[50] = powerspec 2  supports D0 D3  current D0
    cap 05[60] = MSI supports 1 message, 64 bit 
    cap 10[70] = PCI-Express 1 type 0
pcib2@pci0:0:28:0:	class=0x060400 card=0x81ec1043 chip=0x283f8086 rev=0x02 hdr=0x01
    vendor     = 'Intel Corporation'
    device     = '82801H (ICH8 Family) PCIe Port 1'
    class      = bridge
    subclass   = PCI-PCI
    cap 10[40] = PCI-Express 1 root port
    cap 05[80] = MSI supports 1 message 
    cap 0d[90] = PCI Bridge card=0x81ec1043
    cap 01[a0] = powerspec 2  supports D0 D3  current D0
pcib3@pci0:0:28:3:	class=0x060400 card=0x81ec1043 chip=0x28458086 rev=0x02 hdr=0x01
    vendor     = 'Intel Corporation'
    device     = '82801H (ICH8 Family) PCIe Port 4'
    class      = bridge
    subclass   = PCI-PCI
    cap 10[40] = PCI-Express 1 root port
    cap 05[80] = MSI supports 1 message 
    cap 0d[90] = PCI Bridge card=0x81ec1043
    cap 01[a0] = powerspec 2  supports D0 D3  current D0
pcib4@pci0:0:28:4:	class=0x060400 card=0x81ec1043 chip=0x28478086 rev=0x02 hdr=0x01
    vendor     = 'Intel Corporation'
    device     = '82801H (ICH8 Family) PCIe Port 5'
    class      = bridge
    subclass   = PCI-PCI
    cap 10[40] = PCI-Express 1 root port
    cap 05[80] = MSI supports 1 message 
    cap 0d[90] = PCI Bridge card=0x81ec1043
    cap 01[a0] = powerspec 2  supports D0 D3  current D0
uhci2@pci0:0:29:0:	class=0x0c0300 card=0x81ec1043 chip=0x28308086 rev=0x02 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = '82801H (ICH8 Family) USB UHCI'
    class      = serial bus
    subclass   = USB
uhci3@pci0:0:29:1:	class=0x0c0300 card=0x81ec1043 chip=0x28318086 rev=0x02 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = '82801H (ICH8 Family) USB UHCI'
    class      = serial bus
    subclass   = USB
uhci4@pci0:0:29:2:	class=0x0c0300 card=0x81ec1043 chip=0x28328086 rev=0x02 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = '82801H (ICH8 Family) USB UHCI'
    class      = serial bus
    subclass   = USB
ehci1@pci0:0:29:7:	class=0x0c0320 card=0x81ec1043 chip=0x28368086 rev=0x02 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = '82801H (ICH8 Family) USB2 EHCI'
    class      = serial bus
    subclass   = USB
    cap 01[50] = powerspec 2  supports D0 D3  current D0
    cap 0a[58] = EHCI Debug Port at offset 0xa0 in map 0x14
pcib5@pci0:0:30:0:	class=0x060401 card=0x81ec1043 chip=0x244e8086 rev=0xf2 hdr=0x01
    vendor     = 'Intel Corporation'
    device     = '82801 Family (ICH2/3/4/4/5/5/6/7/8/9,63xxESB) Hub Interface to PCI Bridge'
    class      = bridge
    subclass   = PCI-PCI
    cap 0d[50] = PCI Bridge card=0x81ec1043
isab0@pci0:0:31:0:	class=0x060100 card=0x81ec1043 chip=0x28108086 rev=0x02 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = '82801HB/HR (ICH8/R) LPC Interface Controller'
    class      = bridge
    subclass   = PCI-ISA
    cap 09[e0] = vendor (length 12) Intel cap 1 version 0
		 features: SATA RAID-5, 4 PCI-e x1 slots, SATA RAID-0/1/10
atapci2@pci0:0:31:2:	class=0x01018f card=0x81ec1043 chip=0x28208086 rev=0x02 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = 'ICH8 4 port Serial ATA Storage Controller ?'
    class      = mass storage
    subclass   = ATA
    cap 01[70] = powerspec 3  supports D0 D3  current D0
none1@pci0:0:31:3:	class=0x0c0500 card=0x81ec1043 chip=0x283e8086 rev=0x02 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = '82801H (ICH8 Family) SMBus Controller'
    class      = serial bus
    subclass   = SMBus
atapci3@pci0:0:31:5:	class=0x010185 card=0x81ec1043 chip=0x28258086 rev=0x02 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = '? ICH8 2 port Serial ATA Storage Controller'
    class      = mass storage
    subclass   = ATA
    cap 01[70] = powerspec 3  supports D0 D3  current D0
vgapci0@pci0:1:0:0:	class=0x030000 card=0x00000000 chip=0x039310de rev=0xa1 hdr=0x00
    vendor     = 'Nvidia Corp'
    device     = 'GeForce 7300 GT'
    class      = display
    subclass   = VGA
    cap 01[60] = powerspec 2  supports D0 D3  current D0
    cap 05[68] = MSI supports 1 message, 64 bit 
    cap 10[78] = PCI-Express 1 endpoint
re0@pci0:3:0:0:	class=0x020000 card=0x81681043 chip=0x816810ec rev=0x01 hdr=0x00
    vendor     = 'Realtek Semiconductor'
    device     = 'RTL8168/8111 PCI-E Gigabit Ethernet NIC'
    class      = network
    subclass   = ethernet
    cap 01[40] = powerspec 2  supports D0 D1 D2 D3  current D0
    cap 03[48] = VPD
    cap 05[50] = MSI supports 2 messages, 64 bit 
    cap 10[60] = PCI-Express 1 endpoint
    cap 09[84] = vendor (length 76)
atapci0@pci0:2:0:0:	class=0x010601 card=0x81e41043 chip=0x2363197b rev=0x02 hdr=0x00
    vendor     = 'JMicron Technology Corp'
    device     = 'JMB36X PCIe-to-SATA-300/IDE RAID Controller'
    class      = mass storage
    cap 01[68] = powerspec 2  supports D0 D3  current D0
    cap 10[50] = PCI-Express 1 legacy endpoint IRQ 0
atapci1@pci0:2:0:1:	class=0x010185 card=0x81e41043 chip=0x2363197b rev=0x02 hdr=0x00
    vendor     = 'JMicron Technology Corp'
    device     = 'JMB36X PCIe-to-SATA-300/IDE RAID Controller'
    class      = mass storage
    subclass   = ATA
    cap 01[68] = powerspec 2  supports D0 D3  current D0
puc0@pci0:5:0:0:	class=0x078000 card=0x00121000 chip=0x98359710 rev=0x01 hdr=0x00
    vendor     = 'MosChip Semiconductors (Was: Netmos Technology)'
    device     = 'Nm9835 Parallel/Serial Port Adapter'
    class      = simple comms
puc1@pci0:5:1:0:	class=0x078000 card=0x00121000 chip=0x98359710 rev=0x01 hdr=0x00
    vendor     = 'MosChip Semiconductors (Was: Netmos Technology)'
    device     = 'Nm9835 Parallel/Serial Port Adapter'
    class      = simple comms
dc0@pci0:5:2:0:	class=0x020000 card=0x50323030 chip=0x91021282 rev=0x31 hdr=0x00
    vendor     = 'Davicom Semiconductor Inc.'
    device     = 'DM9102/A/AF 10/100 Mbps Fast Ethernet Controller'
    class      = network
    subclass   = ethernet
    cap 01[50] = powerspec 1  supports D0 D3  current D0

Re: Сом порты :(

Добавлено: 2009-02-18 6:27:41
Vitaliy
Итак считаю тему закрытой т.к. все заработало, после перезагрузки модема. Итог
Собрать ядро с девайсом puc...
Не забыть перегрузить модемы )))
Часовой пояс: UTC+03:00
Страница 1 из 1
Powered by phpBB® Forum Software © phpBB Limited
https://www.phpbb.com/