forum.lissyara.su

Код: Выделить всё

router# ifconfig
rl0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=3808<VLAN_MTU,WOL_UCAST,WOL_MCAST,WOL_MAGIC>
        ether 00:e0:4c:f0:f3:f5
        inet 192.168.0.80 netmask 0xffffff00 broadcast 192.168.0.255
        media: Ethernet autoselect (100baseTX <full-duplex>)
        status: active
rl1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
        options=3808<VLAN_MTU,WOL_UCAST,WOL_MCAST,WOL_MAGIC>
        ether 00:e0:4c:c0:8d:91
        inet 192.168.1.100 netmask 0xffffff00 broadcast 192.168.1.255
        media: Ethernet autoselect (100baseTX <full-duplex>)
        status: active
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
        inet6 fe80::1%lo0 prefixlen 64 scopeid 0x3
        inet6 ::1 prefixlen 128
        inet 127.0.0.1 netmask 0xff000000
pflog0: flags=141<UP,RUNNING,PROMISC> metric 0 mtu 33204
tun0: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> metric 0 mtu 1492
        inet 46.201.2хх.ххх --> 195.5.5.186 netmask 0xffffffff
        Opened by PID 51401

Код: Выделить всё

#################################################################
#
#       MPD configuration file
#
# This file defines the configuration for mpd: what the
# bundles are, what the links are in those bundles, how
# the interface should be configured, various PPP parameters,
# etc. It contains commands just as you would type them
# in at the console. Lines without padding are labels. Lines
# starting with a "#" are comments.
#
# $Id: mpd.conf.sample,v 1.46 2009/04/29 11:04:17 amotin Exp $
#
#################################################################

startup:
# Задаем пароль для доступа в web-intarface
# т.е меняем password на свой пароль
        set user admin password admin
# set user password cancer
# configure the console
        set console self 127.0.0.1 5005
        set console open
# configure the web server
        set web self 0.0.0.0 5006
        set web open

default:
        load pptp_server

pptp_server:
# Определяем диапазон выдаваемых IP удалённым клиентам
# у меня с ...200 по ...220
        set ippool add poolsat 192.168.0.250 192.168.0.254
        create bundle template B
        set iface enable proxy-arp
        set iface idle 0
        set iface enable tcpmssfix
        set ipcp yes vjcomp
# IP адрес сервера, который мы будем показывать клиентам
# в моем случае 192.168.10.254 (можно не реальный IP)
        set ipcp ranges 192.168.0.254/32 ippool poolsat
# Здесь указываем DNS сервер
        set ipcp dns 192.168.0.80
# Здесь указываем Wins сервер
        set ipcp nbns 192.168.0.80


# Enable Microsoft Point-to-Point encryption (MPPE)
        set bundle enable compression
        set ccp yes mppc
        set mppc yes compress e40 e56 e128 stateless

# Create clonable link template named L
        create link template L pptp
# Set bundle template to use
        set link action bundle B
# Multilink adds some overhead, but gives full 1500 MTU
        set link enable multilink
        set link yes acfcomp protocomp
        set link no pap chap eap
        set link enable chap
        set link enable chap-msv1
        set link enable chap-msv2
# We reducing link mtu to avoid GRE packet fragmentation.
        set link mtu 1460
        set link keep-alive 10 60

# Configure PPTP and open link
# Тут указываем IP сетевой карты или имя интерфейса (rl1) смотрящего в интернет
        set pptp self tun0
# Allow to accept calls
        set link enable incoming