forum.lissyara.su

Код: Выделить всё

CountryCode:            7

AreaCode:               812

FAXNumber:              4700100

LongDistancePrefix:     1

InternationalPrefix:    011

DialStringRules:        etc/dialrules

ServerTracing:          1

SessionTracing:         0xFFF

RecvFileMode:           0600

LogFileMode:            0600

DeviceMode:             0600

RingsBeforeAnswer:      1

SpeakerVolume:          off

GettyArgs:              ""

NoCarrierRetrys:        1

MaxRecvPages            10

ModemWaitForConnect:    1

 

Class2Cmd:              AT+FCLASS=2.0   # command to enter class 2.0

Class2BORCmd:           AT+FBO=0        # bit order for phase B/C/D (direct)

Class2CQCmd:            ""              # commands to enable copy quality proc.

Class2AbortCmd:         AT+FKS          # abort session command

Class2CQQueryCmd:       AT+FCQ=?        # query for copy quality capabilities

Class2DCCQueryCmd:      AT+FCC=?        # query for modem capabilities

Class2TBCCmd:           AT+FPP=0        # setup stream mode

Class2CRCmd:            AT+FCR=1        # enable capability to receive

Class2PHCTOCmd:         AT+FCT=30       # set phase C timeout parameter

Class2BUGCmd:           AT+FBU=1        # enable HDLC frame tracing

Class2LIDCmd:           AT+FLI          # set local identifier command

Class2DCCCmd:           AT+FCC=?        # set modem capabilities command

Class2DISCmd:           AT+FIS=?        # set session parameters command

Class2DDISCmd:          ""              # disable pre-dial DIS command hack

Class2CIGCmd:           AT+FPI          # set polling identifier command

Class2NRCmd:            AT+FNR=1,1,1,1  # setup status reporting command

Class2PIECmd:           AT+FIE=0        # disable interrupt-enable command

Class2PTSCmd:           AT+FPS          # set post-page status command

Class2PTSQueryCmd:      AT+FPS?         # set post-page status query command

Class2SPLCmd:           AT+FSP          # set polling indicator command

Class2NFLOCmd:          AT+FLO=0        # set no flow control command

Class2SFLOCmd:          AT+FLO=1        # set software flow control command

Class2HFLOCmd:          AT+FLO=2        # set hardware flow control command

Код: Выделить всё

Mar 14 15:30:26.12: [ 1403]: SESSION BEGIN 000000073 78124701350

Mar 14 15:30:26.12: [ 1403]: HylaFAX (tm) Version 6.0.5

Mar 14 15:30:26.12: [ 1403]: SEND FAX: JOB 19 DEST 4701350 COMMID 000000073 DEVICE '/dev/ttyu0' FROM 'test <ribak@caits.ru>' USER test

Mar 14 15:30:26.12: [ 1403]: STATE CHANGE: RUNNING -> SENDING

Mar 14 15:30:26.12: [ 1403]: <-- [9:AT+FLO=1\r]

Mar 14 15:30:26.16: [ 1403]: --> [2:OK]

Mar 14 15:30:26.16: [ 1403]: <-- [9:AT+FPP=0\r]

Mar 14 15:30:26.19: [ 1403]: --> [2:OK]

Mar 14 15:30:26.19: [ 1403]: <-- [9:AT+FBO=0\r]

Mar 14 15:30:26.22: [ 1403]: --> [2:OK]

Mar 14 15:30:26.22: [ 1403]: <-- [10:AT+FCT=30\r]

Mar 14 15:30:26.25: [ 1403]: --> [2:OK]

Mar 14 15:30:26.25: [ 1403]: <-- [15:AT+FNR=1,1,1,1\r]

Mar 14 15:30:26.28: [ 1403]: --> [2:OK]

Mar 14 15:30:26.28: [ 1403]: <-- [9:AT+FIE=0\r]

Mar 14 15:30:26.31: [ 1403]: --> [2:OK]

Mar 14 15:30:26.31: [ 1403]: <-- [9:AT+FBU=1\r]

Mar 14 15:30:26.34: [ 1403]: --> [2:OK]

Mar 14 15:30:26.34: [ 1403]: <-- [23:AT+FCC=1,5,2,2,1,0,0,0\r]

Mar 14 15:30:26.38: [ 1403]: --> [2:OK]

Mar 14 15:30:26.38: [ 1403]: DIAL 4701350

Mar 14 15:30:26.38: [ 1403]: <-- [12:ATDP4701350\r]

Mar 14 15:30:54.38: [ 1403]: --> [4:+FCO]

Mar 14 15:30:55.09: [ 1403]: --> [31:+FNF:"AD 00 36 04 00 00 00 00 "]

Mar 14 15:30:55.09: [ 1403]: REMOTE NSF ""AD 00 36 04 00 00 00 00 ""

Mar 14 15:30:55.09: [ 1403]: NSF remote fax equipment: unknown

Mar 14 15:30:55.53: [ 1403]: --> [27:+FCI:"             4700100"]

Mar 14 15:30:55.53: [ 1403]: REMOTE CSI "4700100"

Mar 14 15:30:55.54: [ 1403]: --> [20:+FIS:1,5,0,2,1,0,0,0]

Mar 14 15:30:55.54: [ 1403]: --> [2:OK]

Mar 14 15:30:55.54: [ 1403]: REMOTE best rate 14400 bit/s

Mar 14 15:30:55.54: [ 1403]: REMOTE max A4 page width (215 mm)

Mar 14 15:30:55.54: [ 1403]: REMOTE max unlimited page length

Mar 14 15:30:55.54: [ 1403]: REMOTE best vres 7.7 line/mm

Mar 14 15:30:55.54: [ 1403]: REMOTE format support: MH, MR

Mar 14 15:30:55.54: [ 1403]: REMOTE best 0 ms/scanline

Mar 14 15:30:55.54: [ 1403]: USE 14400 bit/s

Mar 14 15:30:55.54: [ 1403]: SEND file "docq/doc23.ps;70"

Mar 14 15:30:55.57: [ 1403]: USE A4 page width (215 mm)

Mar 14 15:30:55.57: [ 1403]: USE unlimited page length

Mar 14 15:30:55.57: [ 1403]: USE 3.85 line/mm

Mar 14 15:30:55.57: [ 1403]: USE 2-D MR

Mar 14 15:30:55.57: [ 1403]: USE 0 ms/scanline

Mar 14 15:30:55.57: [ 1403]: <-- [23:AT+FIS=0,5,0,2,1,0,0,0\r]

Mar 14 15:30:55.61: [ 1403]: --> [2:OK]

Mar 14 15:30:55.61: [ 1403]: <-- [7:AT+FDT\r]

Mar 14 15:31:02.98: [ 1403]: --> [20:+FCS:0,5,0,2,1,0,0,0]

Mar 14 15:31:02.99: [ 1403]: --> [7:CONNECT]

Mar 14 15:31:02.99: [ 1403]: SEND begin page

Mar 14 15:31:02.99: [ 1403]: MODEM set XON/XOFF/FLUSH: input interpreted, output disabled

Mar 14 15:31:03.00: [ 1403]: <-- data [1027]

Mar 14 15:31:03.00: [ 1403]: <-- data [1033]

Mar 14 15:31:03.00: [ 1403]: <-- data [1027]

Mar 14 15:31:05.14: [ 1403]: <-- data [1025]

Mar 14 15:31:05.14: [ 1403]: <-- data [62]

Mar 14 15:31:05.14: [ 1403]: SENT 5182 bytes of data

Mar 14 15:31:05.14: [ 1403]: MODEM set XON/XOFF/DRAIN: input interpreted, output generated

Mar 14 15:31:05.96: [ 1403]: SEND end page

Mar 14 15:31:05.96: [ 1403]: SEND send EOP (no more pages or documents)

Mar 14 15:31:05.96: [ 1403]: <-- data [2]

Mar 14 15:31:09.01: [ 1403]: --> [5:ERROR]

Mar 14 15:31:09.01: [ 1403]: <-- [8:AT+FPS?\r]

Mar 14 15:31:09.04: [ 1403]: --> [1:2]

Mar 14 15:31:09.04: [ 1403]: --> [2:OK]