forum.lissyara.su

Часто, когда ты думаешь, что выбираешь между "сделать хорошо" и "сделать плохо", ты лишь влияешь на момент, когда это будет "сделано через жопу".
https://forum.lissyara.su/

Перезагрузка компьютера при загрузке FreeBSD 9.1

https://forum.lissyara.su/viewtopic.php?f=53&t=39590

Страница 1 из 1

Перезагрузка компьютера при загрузке FreeBSD 9.1

Добавлено: 2013-06-20 9:48:36
McSim
При попытке установить FreBSD 9.0 или 9.1 система перезагружается. Как мне кажется при попытке проинициализировать контроллер scsi. При этом 7.2 ставится нормально.
В общем установил я 9.1 в безопасном режиме, и теперь при загрузке тоже перезагружается. Грузиться только в безопасном режиме.
вывод dmesg при verbose и safe mode

Код: Выделить всё

Copyright (c) 1992-2012 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 9.1-RELEASE #0 r243826: Tue Dec  4 06:55:39 UTC 2012
    root@obrian.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC i386
Preloaded elf kernel "/boot/kernel/kernel" at 0xc13d5000.
Calibrating TSC clock ... TSC clock: 866272796 Hz
CPU: Intel Pentium III (866.27-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x68a  Family = 6  Model = 8  Stepping = 10
  Features=0x383fbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>

Instruction TLB: 4 KB pages, 4-way set associative, 32 entries
Instruction TLB: 4 MB pages, fully associative, 2 entries
Data TLB: 4 KB pages, 4-way set associative, 64 entries
2nd-level cache: 256 KB, 8-way set associative, 32 byte line size
1st-level instruction cache: 16 KB, 4-way set associative, 32 byte line size
Data TLB: 4 MB Pages, 4-way set associative, 8 entries
1st-level data cache: 16 KB, 4-way set associative, 32 byte line size
real memory  = 805306368 (768 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000001426000 - 0x000000002f217fff, 769597440 bytes (187890 pages)
avail memory = 768716800 (733 MB)
INTR: Adding local APIC 0 as a target
bios32: Found BIOS32 Service Directory header at 0xc00fdb80
bios32: Entry = 0xfdb90 (c00fdb90)  Rev = 0  Len = 1
pcibios: PCI BIOS entry at 0xf0000+0xdbb1
pnpbios: Found PnP BIOS data at 0xc00f4cc0
pnpbios: Entry = f0000:3b24  Rev = 1.0
Other BIOS signatures found:
ULE: setup cpu 0
wlan: <802.11 Link Layer>
snd_unit_init() u=0x00ff8000 [512] d=0x00007c00 [32] c=0x000003ff [1024]
feeder_register: snd_unit=-1 snd_maxautovchans=16 latency=5 feeder_rate_min=1 feeder_rate_max=2016000 feeder_rate_round=25
module_register_init: MOD_LOAD (kbdmux, 0xc076f9b0, 0) error 6
nfslock: pseudo-device
mem: <memory>
Pentium Pro MTRR support enabled
VESA: INT 0x10 vector 0xc000:0x1960
VESA: information block
0000   56 45 53 41 00 02 ac 74 00 c0 01 00 00 00 22 00
0010   00 01 40 00 02 02 c1 74 00 c0 c8 74 00 c0 d3 74
0020   00 c0 00 01 01 01 02 01 03 01 05 01 07 01 08 01
0030   09 01 0b 01 0c 01 10 01 11 01 12 01 13 01 14 01
0040   15 01 16 01 17 01 1c 01 18 01 19 01 1a 01 1d 01
0050   1e 01 ff ff 00 00 00 00 00 00 00 00 00 00 00 00
0060   00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0070   00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0080   00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0090   00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00a0   00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00b0   00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00c0   00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00d0   00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00e0   00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00f0   00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0100   4d 61 74 72 6f 78 00 4d 49 4c 4c 45 4e 4e 49 55
0110   4d 00 30 30 00 00 00 00 00 00 00 00 00 00 00 00
0120   00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0130   00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0140   00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0150   00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0160   00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0170   00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0180   00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0190   00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
01a0   00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
01b0   00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
01c0   00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
01d0   00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
01e0   00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
01f0   00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
VESA: 24 mode(s) found
VESA: v2.0, 4096k memory, flags:0x1, mode table:0xc45ce022 (1000022)
VESA: Matrox Graphics Inc.
VESA: Matrox MILLENNIUM 00
io: <I/O>
null: <null device, zero device>
random: <entropy source, Software, Yarrow>
hptrr: RocketRAID 17xx/2xxx SATA controller driver v1.2
ctl: CAM Target Layer loaded
pci_open(1):    mode 1 addr port (0x0cf8) is 0x80002048
pci_open(1a):   mode1res=0x80000000 (0x80000000)
pci_cfgcheck:   device 0 [class=060000] [hdr=80] is there (id=00091166)
pcibios: BIOS version 2.10
pcib0 pcibus 0 on motherboard
pir0: <PCI Interrupt Routing Table: 9 Entries> on motherboard
$PIR: Links after initial probe:
Link  IRQ  Rtd  Ref  IRQs
 0x1  255   N     1  10
0x10  255   N     2  3 4 5 7 9 10 11 12 14 15
0x11  255   N     2  3 4 5 7 9 10 11 12 14 15
0x12  255   N     2  3 4 5 7 9 10 11 12 14 15
0x13  255   N     2  3 4 5 7 9 10 11 12 14 15
0x14  255   N     2  3 4 5 7 9 10 11 12 14 15
0x15  255   N     2  3 4 5 7 9 10 11 12 14 15
0x16  255   N     2  3 4 5 7 9 10 11 12 14 15
0x17  255   N     2  3 4 5 7 9 10 11 12 14 15
0x1f  255   N     1  3 4 5 7 9 10 11 12 14 15
0x18  255   N     2  3 4 5 7 9 10 11 12 14 15
0x19  255   N     2  3 4 5 7 9 10 11 12 14 15
0x1a  255   N     2  3 4 5 7 9 10 11 12 14 15
0x1b  255   N     2  3 4 5 7 9 10 11 12 14 15
0x1c  255   N     1  3 4 5 7 9 10 11 12 14 15
$PIR: Found matching pin for 0.15.INTA at func 2: 10
$PIR: Found matching pin for 0.4.INTA at func 0: 11
$PIR: Found matching pin for 0.6.INTA at func 0: 9
$PIR: Found matching pin for 1.1.INTA at func 0: 10
$PIR: Links after initial IRQ discovery:
Link  IRQ  Rtd  Ref  IRQs
 0x1   10   Y     1  10
0x10  255   N     2  3 4 5 7 9 10 11 12 14 15
0x11  255   N     2  3 4 5 7 9 10 11 12 14 15
0x12  255   N     2  3 4 5 7 9 10 11 12 14 15
0x13  255   N     2  3 4 5 7 9 10 11 12 14 15
0x14  255   N     2  3 4 5 7 9 10 11 12 14 15
0x15  255   N     2  3 4 5 7 9 10 11 12 14 15
0x16   11   Y     2  3 4 5 7 9 10 11 12 14 15
0x17  255   N     2  3 4 5 7 9 10 11 12 14 15
0x1f    9   Y     1  3 4 5 7 9 10 11 12 14 15
0x18   10   Y     2  3 4 5 7 9 10 11 12 14 15
0x19  255   N     2  3 4 5 7 9 10 11 12 14 15
0x1a  255   N     2  3 4 5 7 9 10 11 12 14 15
0x1b  255   N     2  3 4 5 7 9 10 11 12 14 15
0x1c  255   N     1  3 4 5 7 9 10 11 12 14 15
$PIR: IRQs used by BIOS: 9 10 11
$PIR: Interrupt Weights:
[    0   1   2   3   4   5   6   7   8   9  10  11  12  13  14  15 ]
[    0   0   0   0   0   0   0   0   0   1   3   2   0   0   0   0 ]
pci0: <PCI bus> on pcib0
pci0: domain=0, physical bus=0
found-> vendor=0x1166, dev=0x0009, revid=0x05
        domain=0, bus=0, slot=0, func=0
        class=06-00-00, hdrtype=0x00, mfdev=1
        cmdreg=0x0006, statreg=0x2200, cachelnsz=8 (dwords)
        lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1166, dev=0x0009, revid=0x05
        domain=0, bus=0, slot=0, func=1
        class=06-00-00, hdrtype=0x00, mfdev=1
        cmdreg=0x0007, statreg=0x0200, cachelnsz=8 (dwords)
        lattimer=0x10 (480 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x102b, dev=0x0519, revid=0x01
        domain=0, bus=0, slot=4, func=0
        class=03-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0083, statreg=0x0280, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=11
        map[10]: type Memory, range 32, base 0xfeafc000, size 14, enabled
        map[14]: type Prefetchable Memory, range 32, base 0xfd800000, size 23, enabled
$PIR: 0:4 INTA routed to irq 11
found-> vendor=0x8086, dev=0x1229, revid=0x08
        domain=0, bus=0, slot=6, func=0
        class=02-00-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0117, statreg=0x0290, cachelnsz=8 (dwords)
        lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x38 (14000 ns)
        intpin=a, irq=9
        powerspec 2  supports D0 D1 D2 D3  current D0
        map[10]: type Memory, range 32, base 0xfeafa000, size 12, enabled
        map[14]: type I/O Port, range 32, base 0xd800, size  6, enabled
        map[18]: type Memory, range 32, base 0xfe900000, size 20, enabled
$PIR: 0:6 INTA routed to irq 9
found-> vendor=0x1166, dev=0x0200, revid=0x4f
        domain=0, bus=0, slot=15, func=0
        class=06-01-00, hdrtype=0x00, mfdev=1
        cmdreg=0x0007, statreg=0x0200, cachelnsz=0 (dwords)
        lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        map[90]: type I/O Port, range 32, base 0x580, size  4, enabled
found-> vendor=0x1166, dev=0x0211, revid=0x00
        domain=0, bus=0, slot=15, func=1
        class=01-01-8a, hdrtype=0x00, mfdev=1
        cmdreg=0x0000, statreg=0x0200, cachelnsz=0 (dwords)
        lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        map[20]: type I/O Port, range 32, base 0xffa0, size  4, port disabled
found-> vendor=0x1166, dev=0x0220, revid=0x04
        domain=0, bus=0, slot=15, func=2
        class=0c-03-10, hdrtype=0x00, mfdev=1
        cmdreg=0x0117, statreg=0x0280, cachelnsz=8 (dwords)
        lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x50 (20000 ns)
        intpin=a, irq=10
        map[10]: type Memory, range 32, base 0xfeafb000, size 12, enabled
$PIR: 0:15 INTA routed to irq 10
vgapci0: <VGA-compatible display> mem 0xfeafc000-0xfeafffff,0xfd800000-0xfdffffff irq 11 at device 4.0 on pci0
fxp0: <Intel 82559 Pro/100 Ethernet> port 0xd800-0xd83f mem 0xfeafa000-0xfeafafff,0xfe900000-0xfe9fffff irq 9 at device 6.0 on pci0
fxp0: using memory space register mapping
fxp0: PCI IDs: 8086 1229 8086 3000 0008
fxp0: Dynamic Standby mode is disabled
miibus0: <MII bus> on fxp0
inphy0: <i82555 10/100 media interface> PHY 1 on miibus0
inphy0: OUI 0x005500, model 0x0015, rev. 4
inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto, auto-flow
fxp0: bpf attached
fxp0: Ethernet address: 00:30:48:21:28:9d
isab0: <PCI-ISA bridge> port 0x580-0x58f at device 15.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <ServerWorks ROSB4 WDMA2 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf at device 15.1 on pci0
ata0: <ATA channel> at channel 0 on atapci0
ata1: <ATA channel> at channel 1 on atapci0
ohci0: <OHCI (generic) USB controller> mem 0xfeafb000-0xfeafbfff irq 10 at device 15.2 on pci0
ohci0: (New OHCI DeviceId=0x02201166)
usbus0 on ohci0
usbus0: bpf attached
ohci0: usbpf: Attached
pcib1 pcibus 1 on motherboard
pir: pir0 already exists; skipping it
pci1: <PCI bus> on pcib1
pci1: domain=0, physical bus=1
found-> vendor=0x1000, dev=0x1960, revid=0x01
        domain=0, bus=1, slot=1, func=0
        class=01-04-00, hdrtype=0x00, mfdev=0
        cmdreg=0x0116, statreg=0x04b0, cachelnsz=8 (dwords)
        lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
        intpin=a, irq=10
        powerspec 2  supports D0 D3  current D0
        map[10]: type Prefetchable Memory, range 32, base 0xfe7f0000, size 16, enabled
$PIR: 1:1 INTA routed to irq 10
amr0: <LSILogic MegaRAID 1.53> mem 0xfe7f0000-0xfe7fffff irq 10 at device 1.0 on pci1
amr0: delete logical drives supported by controller
amr0: <LSILogic MegaRAID SCSI 320-1> Firmware 1L37, BIOS G119, 64MB RAM
cpu0 on motherboard
ex_isa_identify()
ahc_isa_probe 0: ioport 0xc00 alloc failed
ahc_isa_probe 1: ioport 0x1c00 alloc failed
ahc_isa_probe 2: ioport 0x2c00 alloc failed
ahc_isa_probe 3: ioport 0x3c00 alloc failed
ahc_isa_probe 4: ioport 0x4c00 alloc failed
ahc_isa_probe 5: ioport 0x5c00 alloc failed
ahc_isa_probe 6: ioport 0x6c00 alloc failed
ahc_isa_probe 7: ioport 0x7c00 alloc failed
ahc_isa_probe 8: ioport 0x8c00 alloc failed
ahc_isa_probe 9: ioport 0x9c00 alloc failed
ahc_isa_probe 10: ioport 0xac00 alloc failed
ahc_isa_probe 11: ioport 0xbc00 alloc failed
ahc_isa_probe 12: ioport 0xcc00 alloc failed
ahc_isa_probe 13: ioport 0xdc00 alloc failed
ahc_isa_probe 14: ioport 0xec00 alloc failed
pnpbios: 13 devices, largest 234 bytes
PNP0c01: adding fixed memory32 range 0-0x9fbff, size=0x9fc00
PNP0c01: adding fixed memory32 range 0x9fc00-0x9ffff, size=0x400
PNP0c01: adding fixed memory32 range 0xe0000-0xfffff, size=0x20000
PNP0c01: adding fixed memory32 range 0x100000-0x2ffeffff, size=0x2fef0000
PNP0c01: adding fixed memory32 range 0x2fff0000-0x2fffefff, size=0xf000
PNP0c01: adding fixed memory32 range 0x2ffff000-0x2fffffff, size=0x1000
PNP0c01: adding fixed memory32 range 0xfec00000-0xfec00fff, size=0x1000
PNP0c01: adding fixed memory32 range 0xfec01000-0xfec01fff, size=0x1000
PNP0c01: adding fixed memory32 range 0xfee00000-0xfee00fff, size=0x1000
PNP0c01: adding fixed memory32 range 0xfff80000-0xffffffff, size=0x80000
pnpbios: handle 0 device ID PNP0c01 (010cd041)
PNP0200: adding dma mask 0x10
PNP0200: adding io range 0-0xf, size=0x10, align=0x1
PNP0200: adding io range 0x80-0x90, size=0x11, align=0x1
PNP0200: adding io range 0x94-0x9f, size=0xc, align=0x1
PNP0200: adding io range 0xc0-0xde, size=0x1f, align=0x1
pnpbios: handle 2 device ID PNP0200 (0002d041)
PNP0100: adding irq mask 0x1
PNP0100: adding io range 0x40-0x43, size=0x4, align=0x1
pnpbios: handle 3 device ID PNP0100 (0001d041)
PNP0b00: adding irq mask 0x100
PNP0b00: adding io range 0x70-0x71, size=0x2, align=0x1
pnpbios: handle 4 device ID PNP0b00 (000bd041)
PNP0303: adding irq mask 0x2
PNP0303: adding io range 0x60-0x60, size=0x1, align=0x1
PNP0303: adding io range 0x64-0x64, size=0x1, align=0x1
pnpbios: handle 5 device ID PNP0303 (0303d041)
PNP0800: adding io range 0x61-0x61, size=0x1, align=0x1
pnpbios: handle 6 device ID PNP0800 (0008d041)
PNP0c04: adding irq mask 0x2000
PNP0c04: adding io range 0xf0-0xff, size=0x10, align=0x1
pnpbios: handle 7 device ID PNP0c04 (040cd041)
PNP0c02: adding io range 0x4d0-0x4d1, size=0x2, align=0x1
PNP0c02: adding io range 0xcf8-0xcff, size=0x8, align=0x1
PNP0c02: adding io range 0x10-0x1f, size=0x10, align=0x1
PNP0c02: adding io range 0x40b-0x40b, size=0x1, align=0x1
PNP0c02: adding io range 0x4d6-0x4d6, size=0x1, align=0x1
PNP0c02: adding io range 0xc00-0xc01, size=0x2, align=0x1
PNP0c02: adding io range 0xc14-0xc14, size=0x1, align=0x1
PNP0c02: adding io range 0xc49-0xc4a, size=0x2, align=0x1
PNP0c02: adding io range 0xc52-0xc52, size=0x1, align=0x1
PNP0c02: adding io range 0xc6c-0xc6c, size=0x1, align=0x1
PNP0c02: adding io range 0xc6f-0xc6f, size=0x1, align=0x1
PNP0c02: adding io range 0xcd6-0xcd7, size=0x2, align=0x1
PNP0c02: adding io range 0xf50-0xf58, size=0x9, align=0x1
PNP0c02: adding io range 0x374-0x375, size=0x2, align=0x1
PNP0c02: adding io range 0x377-0x377, size=0x1, align=0x1
PNP0c02: adding fixed memory32 range 0xca200-0xcffff, size=0x5e00
pnpbios: handle 8 device ID PNP0c02 (020cd041)
PNP0c02: adding io range 0x2e-0x2e, size=0x1, align=0x1
PNP0c02: adding io range 0x2f-0x2f, size=0x1, align=0x1
PNP0c02: adding io range 0x580-0x58f, size=0x10, align=0x1
PNP0c02: adding io range 0x530-0x531, size=0x2, align=0x1
PNP0c02: adding io range 0x540-0x55f, size=0x20, align=0x1
PNP0c02: adding io range 0x500-0x51f, size=0x20, align=0x1
PNP0c02: adding io range 0xc98-0xc98, size=0x1, align=0x1
pnpbios: handle 9 device ID PNP0c02 (020cd041)
PNP0f13: adding irq mask 0x1000
pnpbios: handle 10 device ID PNP0f13 (130fd041)
pnpbios: handle 11 device ID PNP0a03 (030ad041)
PNP0700: adding io range 0x3f0-0x3f5, size=0x6, align=0x1
PNP0700: adding irq mask 0x40
PNP0700: adding dma mask 0x4
pnpbios: handle 12 device ID PNP0700 (0007d041)
pnp_identify: Trying Read_Port at 203
pnp_identify: Trying Read_Port at 243
pnp_identify: Trying Read_Port at 283
pnp_identify: Trying Read_Port at 2c3
pnp_identify: Trying Read_Port at 303
pnp_identify: Trying Read_Port at 343
pnp_identify: Trying Read_Port at 383
pnp_identify: Trying Read_Port at 3c3
PNP Identify complete
isa_probe_children: disabling PnP devices
pmtimer0 on isa0
unknown: <PNP0c01> can't assign resources (memory)
unknown: <PNP0c01> at iomem 0-0x9fbff pnpid PNP0c01 on isa0
attimer0: <AT timer> at port 0x40-0x43 irq 0 pnpid PNP0100 on isa0
Timecounter "i8254" frequency 1193182 Hz quality 0
Event timer "i8254" frequency 1193182 Hz quality 100
atrtc0: <AT realtime clock> at port 0x70-0x71 irq 8 pnpid PNP0b00 on isa0
atrtc0: registered as a time-of-day clock (resolution 1000000us, adjustment 0.500000000s)
Event timer "RTC" frequency 32768 Hz quality 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 irq 1 pnpid PNP0303 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
atkbd0: [GIANT-LOCKED]
psm0: unable to allocate IRQ
(null) failed to probe at port 0x61 pnpid PNP0800 on isa0
unknown: <PNP0c02> can't assign resources (port)
unknown: <PNP0c02> at port 0x2e,0x2f,0x580-0x58f pnpid PNP0c02 on isa0
psmcpnp0: <PS/2 mouse port> at irq 12 pnpid PNP0f13 on isa0
psm0: current command byte:0065
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model IntelliMouse Explorer, device ID 4-00, 5 buttons
psm0: config:00000000, flags:00000008, packet size:4
psm0: syncmask:08, syncbits:00
(null) failed to probe at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 pnpid PNP0700 on isa0
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
atkbdc: atkbdc0 already exists; skipping it
atrtc: atrtc0 already exists; skipping it
attimer: attimer0 already exists; skipping it
sc: sc0 already exists; skipping it
isa_probe_children: probing non-PnP devices
orm0: <ISA Option ROM> at iomem 0xc0000-0xc7fff pnpid ORM0000 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: scteken (teken terminal)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fdc0 failed to probe at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
ppc0: parallel port not found.
ppc0 failed to probe at irq 7 on isa0
uart0 failed to probe at port 0x3f8-0x3ff irq 4 on isa0
uart1 failed to probe at port 0x2f8-0x2ff irq 3 on isa0
wbwd0 failed to probe on isa0
isa_probe_children: probing PnP devices
unknown: <PNP0c01> can't assign resources (memory)
unknown: <PNP0c01> at iomem 0-0x9fbff pnpid PNP0c01 on isa0
unknown: <PNP0c02> can't assign resources (port)
unknown: <PNP0c02> at port 0x2e,0x2f,0x580-0x58f pnpid PNP0c02 on isa0
fdc: fdc-1 already exists; skipping it
driver bug: Unable to set devclass (devname: (null))
Device configuration finished.
procfs registered
Timecounters tick every 1.000 msec
vlan: initialized, using hash tables with chaining
lo0: bpf attached
hptrr: no controller detected.
amr0: delete logical drives supported by controller
amrd0: <LSILogic MegaRAID logical drive> on amr0
amrd0: 70006MB (143372288 sectors) RAID 1 (optimal)
GEOM: new disk amrd0
usbus0: 12Mbps Full Speed USB v1.0
ata0: reset tp1 mask=03 ostat0=60 ostat1=70
ugen0.1: <0x1166> at usbus0
uhub0: <0x1166 OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ata0: stat0=0x20 err=0x20 lsb=0x20 msb=0x20
ata0: stat1=0x30 err=0x30 lsb=0x30 msb=0x30
ata0: reset tp2 stat0=20 stat1=30 devices=0x0
ata1: reset tp1 mask=03 ostat0=60 ostat1=70
ata1: stat0=0x20 err=0x20 lsb=0x20 msb=0x20
ata1: stat1=0x30 err=0x30 lsb=0x30 msb=0x30
ata1: reset tp2 stat0=20 stat1=30 devices=0x0
uhub0: 4 ports with 4 removable, self powered
Timecounter "TSC" frequency 866272796 Hz quality 800
Trying to mount root from ufs:/dev/amrd0p2 [rw]...
start_init: trying /sbin/init
fxp0: link state changed to UP
Из последнего, что успеваю заметить перед перезагрузкой: uhub0: 4 ports with 4 removable, self powered

Подскажите, пожалуйста, в каком направлении копать?

Re: Перезагрузка компьютера при загрузке FreeBSD 9.1

Добавлено: 2013-06-20 10:14:00
BirdGovorun
8.4 устанавливайте, на таких машинах 9.х обычно не работает.

Re: Перезагрузка компьютера при загрузке FreeBSD 9.1

Добавлено: 2013-06-20 15:04:33
Alvares
а потом проапдейтиться до 9 :) Кто-то тут с тачкой новее так мучался.

Re: Перезагрузка компьютера при загрузке FreeBSD 9.1

Добавлено: 2013-06-20 15:37:08
BirdGovorun
Alvares писал(а):а потом проапдейтиться до 9 :) Кто-то тут с тачкой новее так мучался.
Не факт, что заработает.

Re: Перезагрузка компьютера при загрузке FreeBSD 9.1

Добавлено: 2013-06-20 16:18:13
McSim
Скачал образ 8.4 - та же петрушка
Вот последнее, что выдается перед перезагрузкой:

Re: Перезагрузка компьютера при загрузке FreeBSD 9.1

Добавлено: 2013-06-20 16:26:41
BirdGovorun
После установки 9.х, чтобы поставить 8.4, надо удалить GPT ,
самое простое(но долго), это забить весь диск нулями, dd вам в помощь.

Re: Перезагрузка компьютера при загрузке FreeBSD 9.1

Добавлено: 2013-09-30 15:56:46
mika3444
BirdGovorun писал(а):8.4 устанавливайте, на таких машинах 9.х обычно не работает.
Можно узнать поподробнее почему ребутится 9.x?
Ни где не написано что она более требовательна и на одних машинах будет работать, а на других нет. Можно пруфлинк? Или вы это так, для красного словца?

У меня около 10 серверов на freebsd. Все на десктоповом железе. Нашел закономерность: убрать процессор на котором написано 800.
Т.е. например такой процессор будет работать: P4 3.06/1M/533/84A
А если вместо 533 будет 800, то будет ребутится когда по ssh что-то устанавливаю или пересобираю ядро.
Я поделился своим опытом, надеюсь многим поможет.
Мучился с каждым сервером, на изучение этой проблемы потратил 2 месяца.
И уже успокоился,
а сегодня с нормальным процом сервак стал глючить. Не знаю что делать. Хочется узнать поподробнее об этой проблеме.

Уже вроде собираются выпускать 10, на сколько вероятно что 10 версия не будет глючить?

Re: Перезагрузка компьютера при загрузке FreeBSD 9.1

Добавлено: 2013-10-02 13:04:23
Electronik
800 частота шины. проверяйте железо, попробуйте загрузиться в режиме Disable ACPI
и не подскажите, что такого вы используете в 9.х, чего нет в 8.4?

Re: Перезагрузка компьютера при загрузке FreeBSD 9.1

Добавлено: 2013-10-02 15:15:30
mika3444
Ничего не использую.
во всех серверах одно и тоже: PF, transparent Squid (сейчас 3.2.13), dhcp, bind (9.9.3-P2),
еще разные программы nmap, trafshow, скрипты для подсчета логов squid и т.д.
Обычно я переустанавливаю от нечего делать, всегда ставлю самые последние стабильные версии.
Последний раз все переустановили на 9.1 и бинд 9.9.3-P2 из-за атак типа isc.org (в логах постоянно идут запросы что пезолвят isc.org, думаю Вы слышали о таком типе атаки). Не сильно помогло. но переустановил. Красиво все, работает отлично.

Re: Перезагрузка компьютера при загрузке FreeBSD 9.1

Добавлено: 2013-10-02 18:00:19
mika3444
Очень хотелось бы получить ответ, мнение, предположение. С чего это вдруг начиная с 9 версии проблемы с железом? Кто-нибудь сталкивался что на 800 при пересборке ядра (или установке например openssl, squid, portsnap fetch update) "уходит в перезагрузку"?
Часовой пояс: UTC+03:00
Страница 1 из 1
Powered by phpBB® Forum Software © phpBB Limited
https://www.phpbb.com/