Страница 1 из 1

freebsd 7.1, adm780v, ide hdd

Добавлено: 2009-03-20 21:10:59
ski
Столкнулся тут:
материнская плата на amd780v, freebsd7.1-release (образ взят с сайта бсд), ide hdd 40gb, sata-300 hdd 500gb
Система упорно предлагает ставиться на sata винчестер, полностью игнорируя ide. Посмотрел - при загрузке в опознанных устройствах фигурируют ad4 - sata hdd, ad0 - sata-dvd. ide диска нету. Я так понимаю, что на этой материнке ide реализован контроллером, который bsd не знает, и поставить на него систему не судьба? Или есть какие-то обходные варианты?

Re: freebsd 7.1, adm780v, ide hdd

Добавлено: 2009-03-20 21:18:32
Alex Keda

Код: Выделить всё

dmesg
pciconf -lv
в студию

Re: freebsd 7.1, adm780v, ide hdd

Добавлено: 2009-03-20 21:49:04
ski

Код: Выделить всё

dmesg
Copyright (c) 1992-2009 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
   The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 7.1-RELEASE #0: Thu Jan  1 14:37:25 UTC 2009
    root@logan.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: AMD Athlon(tm) 64 X2 Dual Core Processor 5000+ (2600.11-MHz 686-class CPU)
  Origin = "AuthenticAMD"  Id = 0x60fb1  Stepping = 1
  Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT>
  Features2=0x2001<SSE3,CX16>
  AMD Features=0xea500800<SYSCALL,NX,MMX+,FFXSR,RDTSCP,LM,3DNow!+,3DNow!>
  AMD Features2=0x11f<LAHF,CMP,SVM,ExtAPIC,CR8,Prefetch>
  Cores per package: 2
real memory  = 3489202176 (3327 MB)
avail memory = 3405717504 (3247 MB)
ACPI APIC Table: <7302MS A7302100>
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
 cpu0 (BSP): APIC ID:  0
 cpu1 (AP): APIC ID:  1
ioapic0 <Version 2.1> irqs 0-23 on motherboard
kbd1 at kbdmux0
ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
acpi0: <7302MS A7302100> on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
acpi0: reservation of ffb80000, 80000 (3) failed
acpi0: reservation of fff00000, 100000 (3) failed
acpi0: reservation of 0, a0000 (3) failed
acpi0: reservation of 100000, cff00000 (3) failed
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <32-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> irq 18 at device 2.0 on pci0
pci1: <ACPI PCI bus> on pcib1
vgapci0: <VGA-compatible display> port 0xb000-0xb0ff mem 0xd0000000-0xdfffffff,0xfeaf0000-0xfeafffff irq 18 at device 0.0 on pci1
pci1: <multimedia> at device 0.1 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> irq 17 at device 5.0 on pci0
pci2: <ACPI PCI bus> on pcib2
re0: <RealTek 8168/8168B/8168C/8168CP/8168D/8111B/8111C/8111CP PCIe Gigabit Ethernet> port 0xc800-0xc8ff mem 0xfdfff000-0xfdffffff,0xfdfe0000-0xfdfeffff irq 17 at device 0.0 on pci2
re0: Chip rev. 0x3c000000
re0: MAC rev. 0x00200000
miibus0: <MII bus> on re0
rgephy0: <RTL8169S/8110S/8211B media interface> PHY 1 on miibus0
rgephy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
re0: Ethernet address: 00:1d:92:ee:86:a0
re0: [FILTER]
atapci0: <ATI IXP700 SATA300 controller> port 0xa000-0xa007,0x9000-0x9003,0x8000-0x8007,0x7000-0x7003,0x6000-0x600f mem 0xfe9ff800-0xfe9ffbff irq 22 at device 17.0 on pci0
atapci0: [ITHREAD]
atapci0: AHCI Version 01.10 controller with 4 ports detected
ata2: <ATA channel 0> on atapci0
ata2: [ITHREAD]
ata3: <ATA channel 1> on atapci0
ata3: [ITHREAD]
ata4: <ATA channel 2> on atapci0
ata4: [ITHREAD]
ata5: <ATA channel 3> on atapci0
ata5: [ITHREAD]
ohci0: <OHCI (generic) USB controller> mem 0xfe9fe000-0xfe9fefff irq 16 at device 18.0 on pci0
ohci0: [GIANT-LOCKED]
ohci0: [ITHREAD]
usb0: OHCI version 1.0, legacy support
usb0: SMM does not respond, resetting
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 3 ports with 3 removable, self powered
ohci1: <OHCI (generic) USB controller> mem 0xfe9fd000-0xfe9fdfff irq 16 at device 18.1 on pci0
ohci1: [GIANT-LOCKED]
ohci1: [ITHREAD]
usb1: OHCI version 1.0, legacy support
usb1: SMM does not respond, resetting
usb1: <OHCI (generic) USB controller> on ohci1
usb1: USB revision 1.0
uhub1: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1
uhub1: 3 ports with 3 removable, self powered
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xfe9ff000-0xfe9ff0ff irq 17 at device 18.2 on pci0
ehci0: [GIANT-LOCKED]
ehci0: [ITHREAD]
usb2: EHCI version 1.0
usb2: companion controllers, 3 ports each: usb0 usb1
usb2: <EHCI (generic) USB 2.0 controller> on ehci0
usb2: USB revision 2.0
uhub2: <ATI EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb2
uhub2: 6 ports with 6 removable, self powered
uhub3: <vendor 0x0424 product 0x2504, class 9/0, rev 2.00/0.01, addr 2> on uhub2
uhub3: multiple transaction translators
uhub3: 2 ports with 2 removable, self powered
ohci2: <OHCI (generic) USB controller> mem 0xfe9fc000-0xfe9fcfff irq 18 at device 19.0 on pci0
ohci2: [GIANT-LOCKED]
ohci2: [ITHREAD]
usb3: OHCI version 1.0, legacy support
usb3: SMM does not respond, resetting
usb3: <OHCI (generic) USB controller> on ohci2
usb3: USB revision 1.0
uhub4: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb3
uhub4: 3 ports with 3 removable, self powered
ohci3: <OHCI (generic) USB controller> mem 0xfe9fb000-0xfe9fbfff irq 18 at device 19.1 on pci0
ohci3: [GIANT-LOCKED]
ohci3: [ITHREAD]
usb4: OHCI version 1.0, legacy support
usb4: SMM does not respond, resetting
usb4: <OHCI (generic) USB controller> on ohci3
usb4: USB revision 1.0
uhub5: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb4
uhub5: 3 ports with 3 removable, self powered
ehci1: <EHCI (generic) USB 2.0 controller> mem 0xfe9fa800-0xfe9fa8ff irq 19 at device 19.2 on pci0
ehci1: [GIANT-LOCKED]
ehci1: [ITHREAD]
usb5: EHCI version 1.0
usb5: companion controllers, 3 ports each: usb3 usb4
usb5: <EHCI (generic) USB 2.0 controller> on ehci1
usb5: USB revision 2.0
uhub6: <ATI EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb5
uhub6: 6 ports with 6 removable, self powered
pci0: <serial bus, SMBus> at device 20.0 (no driver attached)
atapci1: <ATI IXP700 UDMA133 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xff00-0xff0f at device 20.1 on pci0
ata0: <ATA channel 0> on atapci1
ata0: [ITHREAD]
pci0: <multimedia> at device 20.2 (no driver attached)
isab0: <PCI-ISA bridge> at device 20.3 on pci0
isa0: <ISA bus> on isab0
pcib3: <ACPI PCI-PCI bridge> at device 20.4 on pci0
pci3: <ACPI PCI bus> on pcib3
pci3: <multimedia, audio> at device 3.0 (no driver attached)
ohci4: <OHCI (generic) USB controller> mem 0xfe9f9000-0xfe9f9fff irq 18 at device 20.5 on pci0
ohci4: [GIANT-LOCKED]
ohci4: [ITHREAD]
usb6: OHCI version 1.0, legacy support
usb6: SMM does not respond, resetting
usb6: <OHCI (generic) USB controller> on ohci4
usb6: USB revision 1.0
uhub7: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb6
uhub7: 2 ports with 2 removable, self powered
acpi_button0: <Power Button> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: [ITHREAD]
psm0: model IntelliMouse Explorer, device ID 4
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
sio0: [FILTER]
fdc0: <floppy drive controller (FDE)> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: [FILTER]
acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
acpi_hpet0: HPET never increments, disabling
device_attach: acpi_hpet0 attach returned 6
cpu0: <ACPI CPU> on acpi0
acpi_throttle0: <ACPI CPU Throttling> on cpu0
powernow0: <PowerNow! K8> on cpu0
device_attach: powernow0 attach returned 6
cpu1: <ACPI CPU> on acpi0
powernow1: <PowerNow! K8> on cpu1
device_attach: powernow1 attach returned 6
acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
acpi_hpet0: HPET never increments, disabling
device_attach: acpi_hpet0 attach returned 6
pmtimer0 on isa0
orm0: <ISA Option ROM> at iomem 0xc0000-0xcefff pnpid ORM0000 on isa0
ppc0: parallel port not found.
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounters tick every 1.000 msec
md0: Preloaded image </boot/mfsroot> 4423680 bytes at 0xc0d7f830
ad4: 476938MB <SAMSUNG HD501LJ CR100-10> at ata2-master SATA300
acd0: DVDR <Optiarc DVD RW AD-7173S/1-02> at ata4-master SATA150
SMP: AP CPU #1 Launched!
GEOM_LABEL: Label for provider acd0 is iso9660/FreeBSD_Install.
Trying to mount root from ufs:/dev/md0
Waiting (max 60 seconds) for system process `vnlru' to stop...done
Waiting (max 60 seconds) for system process `bufdaemon' to stop...done
Waiting (max 60 seconds) for system process `syncer' to stop...
Syncing disks, vnodes remaining...0 done
All buffers synced.
Copyright (c) 1992-2009 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
   The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 7.1-RELEASE #0: Thu Jan  1 14:37:25 UTC 2009
    root@logan.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: AMD Athlon(tm) 64 X2 Dual Core Processor 5000+ (2600.11-MHz 686-class CPU)
  Origin = "AuthenticAMD"  Id = 0x60fb1  Stepping = 1
  Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT>
  Features2=0x2001<SSE3,CX16>
  AMD Features=0xea500800<SYSCALL,NX,MMX+,FFXSR,RDTSCP,LM,3DNow!+,3DNow!>
  AMD Features2=0x11f<LAHF,CMP,SVM,ExtAPIC,CR8,Prefetch>
  Cores per package: 2
real memory  = 3489202176 (3327 MB)
avail memory = 3405717504 (3247 MB)
ACPI APIC Table: <7302MS A7302100>
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
 cpu0 (BSP): APIC ID:  0
 cpu1 (AP): APIC ID:  1
ioapic0 <Version 2.1> irqs 0-23 on motherboard
kbd1 at kbdmux0
ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
acpi0: <7302MS A7302100> on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
acpi0: reservation of ffb80000, 80000 (3) failed
acpi0: reservation of fff00000, 100000 (3) failed
acpi0: reservation of 0, a0000 (3) failed
acpi0: reservation of 100000, cff00000 (3) failed
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <32-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> irq 18 at device 2.0 on pci0
pci1: <ACPI PCI bus> on pcib1
vgapci0: <VGA-compatible display> port 0xb000-0xb0ff mem 0xd0000000-0xdfffffff,0xfeaf0000-0xfeafffff irq 18 at device 0.0 on pci1
pci1: <multimedia> at device 0.1 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> irq 17 at device 5.0 on pci0
pci2: <ACPI PCI bus> on pcib2
re0: <RealTek 8168/8168B/8168C/8168CP/8168D/8111B/8111C/8111CP PCIe Gigabit Ethernet> port 0xc800-0xc8ff mem 0xfdfff000-0xfdffffff,0xfdfe0000-0xfdfeffff irq 17 at device 0.0 on pci2
re0: Chip rev. 0x3c000000
re0: MAC rev. 0x00200000
miibus0: <MII bus> on re0
rgephy0: <RTL8169S/8110S/8211B media interface> PHY 1 on miibus0
rgephy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
re0: Ethernet address: 00:1d:92:ee:86:a0
re0: [FILTER]
atapci0: <ATI IXP700 SATA300 controller> port 0xa000-0xa007,0x9000-0x9003,0x8000-0x8007,0x7000-0x7003,0x6000-0x600f mem 0xfe9ff800-0xfe9ffbff irq 22 at device 17.0 on pci0
atapci0: [ITHREAD]
atapci0: AHCI Version 01.10 controller with 4 ports detected
ata2: <ATA channel 0> on atapci0
ata2: [ITHREAD]
ata3: <ATA channel 1> on atapci0
ata3: [ITHREAD]
ata4: <ATA channel 2> on atapci0
ata4: [ITHREAD]
ata5: <ATA channel 3> on atapci0
ata5: [ITHREAD]
ohci0: <OHCI (generic) USB controller> mem 0xfe9fe000-0xfe9fefff irq 16 at device 18.0 on pci0
ohci0: [GIANT-LOCKED]
ohci0: [ITHREAD]
usb0: OHCI version 1.0, legacy support
usb0: SMM does not respond, resetting
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 3 ports with 3 removable, self powered
ohci1: <OHCI (generic) USB controller> mem 0xfe9fd000-0xfe9fdfff irq 16 at device 18.1 on pci0
ohci1: [GIANT-LOCKED]
ohci1: [ITHREAD]
usb1: OHCI version 1.0, legacy support
usb1: SMM does not respond, resetting
usb1: <OHCI (generic) USB controller> on ohci1
usb1: USB revision 1.0
uhub1: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1
uhub1: 3 ports with 3 removable, self powered
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xfe9ff000-0xfe9ff0ff irq 17 at device 18.2 on pci0
ehci0: [GIANT-LOCKED]
ehci0: [ITHREAD]
usb2: EHCI version 1.0
usb2: companion controllers, 3 ports each: usb0 usb1
usb2: <EHCI (generic) USB 2.0 controller> on ehci0
usb2: USB revision 2.0
uhub2: <ATI EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb2
uhub2: 6 ports with 6 removable, self powered
uhub3: <vendor 0x0424 product 0x2504, class 9/0, rev 2.00/0.01, addr 2> on uhub2
uhub3: multiple transaction translators
uhub3: 2 ports with 2 removable, self powered
ohci2: <OHCI (generic) USB controller> mem 0xfe9fc000-0xfe9fcfff irq 18 at device 19.0 on pci0
ohci2: [GIANT-LOCKED]
ohci2: [ITHREAD]
usb3: OHCI version 1.0, legacy support
usb3: SMM does not respond, resetting
usb3: <OHCI (generic) USB controller> on ohci2
usb3: USB revision 1.0
uhub4: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb3
uhub4: 3 ports with 3 removable, self powered
ohci3: <OHCI (generic) USB controller> mem 0xfe9fb000-0xfe9fbfff irq 18 at device 19.1 on pci0
ohci3: [GIANT-LOCKED]
ohci3: [ITHREAD]
usb4: OHCI version 1.0, legacy support
usb4: SMM does not respond, resetting
usb4: <OHCI (generic) USB controller> on ohci3
usb4: USB revision 1.0
uhub5: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb4
uhub5: 3 ports with 3 removable, self powered
ehci1: <EHCI (generic) USB 2.0 controller> mem 0xfe9fa800-0xfe9fa8ff irq 19 at device 19.2 on pci0
ehci1: [GIANT-LOCKED]
ehci1: [ITHREAD]
usb5: EHCI version 1.0
usb5: companion controllers, 3 ports each: usb3 usb4
usb5: <EHCI (generic) USB 2.0 controller> on ehci1
usb5: USB revision 2.0
uhub6: <ATI EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb5
uhub6: 6 ports with 6 removable, self powered
pci0: <serial bus, SMBus> at device 20.0 (no driver attached)
atapci1: <ATI IXP700 UDMA133 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xff00-0xff0f at device 20.1 on pci0
ata0: <ATA channel 0> on atapci1
ata0: [ITHREAD]
pci0: <multimedia> at device 20.2 (no driver attached)
isab0: <PCI-ISA bridge> at device 20.3 on pci0
isa0: <ISA bus> on isab0
pcib3: <ACPI PCI-PCI bridge> at device 20.4 on pci0
pci3: <ACPI PCI bus> on pcib3
pci3: <multimedia, audio> at device 3.0 (no driver attached)
ohci4: <OHCI (generic) USB controller> mem 0xfe9f9000-0xfe9f9fff irq 18 at device 20.5 on pci0
ohci4: [GIANT-LOCKED]
ohci4: [ITHREAD]
usb6: OHCI version 1.0, legacy support
usb6: SMM does not respond, resetting
usb6: <OHCI (generic) USB controller> on ohci4
usb6: USB revision 1.0
uhub7: <ATI OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb6
uhub7: 2 ports with 2 removable, self powered
acpi_button0: <Power Button> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: [ITHREAD]
psm0: model IntelliMouse Explorer, device ID 4
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
sio0: [FILTER]
fdc0: <floppy drive controller (FDE)> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: [FILTER]
acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
acpi_hpet0: HPET never increments, disabling
device_attach: acpi_hpet0 attach returned 6
cpu0: <ACPI CPU> on acpi0
acpi_throttle0: <ACPI CPU Throttling> on cpu0
powernow0: <PowerNow! K8> on cpu0
device_attach: powernow0 attach returned 6
cpu1: <ACPI CPU> on acpi0
powernow1: <PowerNow! K8> on cpu1
device_attach: powernow1 attach returned 6
acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
acpi_hpet0: HPET never increments, disabling
device_attach: acpi_hpet0 attach returned 6
pmtimer0 on isa0
orm0: <ISA Option ROM> at iomem 0xc0000-0xcefff pnpid ORM0000 on isa0
ppc0: parallel port not found.
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounters tick every 1.000 msec
md0: Preloaded image </boot/mfsroot> 4423680 bytes at 0xc0d7f830
ad4: 476938MB <SAMSUNG HD501LJ CR100-10> at ata2-master SATA300
acd0: DVDR <Optiarc DVD RW AD-7173S/1-02> at ata4-master SATA150
SMP: AP CPU #1 Launched!
GEOM_LABEL: Label for provider acd0 is iso9660/FreeBSD_Install.
Trying to mount root from ufs:/dev/md0
umass0: <SMI Corporation USB DISK, class 0/0, rev 2.00/11.00, addr 2> on uhub6
da0 at umass-sim0 bus 0 target 0 lun 0
da0: < GOODDRIVEFR 1100> Removable Direct Access SCSI-0 device 
da0: 40.000MB/s transfers
da0: 1935MB (3963904 512 byte sectors: 255H 63S/T 246C)
GEOM_LABEL: Label for provider da0 is msdosfs/NEW VOLUME.
GEOM_LABEL: Label msdosfs/NEW VOLUME removed.

Код: Выделить всё

pciconf -lv
hostb0@pci0:0:0:0:   class=0x060000 card=0x96001022 chip=0x96001022 rev=0x00 hdr=0x00
    class      = bridge
    subclass   = HOST-PCI
pcib1@pci0:0:2:0: class=0x060400 card=0x96001022 chip=0x96031022 rev=0x00 hdr=0x01
    class      = bridge
    subclass   = PCI-PCI
pcib2@pci0:0:5:0: class=0x060400 card=0x96001022 chip=0x96051022 rev=0x00 hdr=0x01
    class      = bridge
    subclass   = PCI-PCI
atapci0@pci0:0:17:0: class=0x01018f card=0x73021462 chip=0x43901002 rev=0x00 hdr=0x00
    class      = mass storage
    subclass   = ATA
ohci0@pci0:0:18:0:   class=0x0c0310 card=0x73021462 chip=0x43971002 rev=0x00 hdr=0x00
    class      = serial bus
    subclass   = USB
ohci1@pci0:0:18:1:   class=0x0c0310 card=0x73021462 chip=0x43981002 rev=0x00 hdr=0x00
    class      = serial bus
    subclass   = USB
ehci0@pci0:0:18:2:   class=0x0c0320 card=0x73021462 chip=0x43961002 rev=0x00 hdr=0x00
    class      = serial bus
    subclass   = USB
ohci2@pci0:0:19:0:   class=0x0c0310 card=0x73021462 chip=0x43971002 rev=0x00 hdr=0x00
    class      = serial bus
    subclass   = USB
ohci3@pci0:0:19:1:   class=0x0c0310 card=0x73021462 chip=0x43981002 rev=0x00 hdr=0x00
    class      = serial bus
    subclass   = USB
ehci1@pci0:0:19:2:   class=0x0c0320 card=0x73021462 chip=0x43961002 rev=0x00 hdr=0x00
    class      = serial bus
    subclass   = USB
none0@pci0:0:20:0:   class=0x0c0500 card=0x73021462 chip=0x43851002 rev=0x3a hdr=0x00
    class      = serial bus
    subclass   = SMBus
atapci1@pci0:0:20:1: class=0x01018a card=0x73021462 chip=0x439c1002 rev=0x00 hdr=0x00
    class      = mass storage
    subclass   = ATA
none1@pci0:0:20:2:   class=0x040300 card=0x73021462 chip=0x43831002 rev=0x00 hdr=0x00
    class      = multimedia
isab0@pci0:0:20:3:   class=0x060100 card=0x73021462 chip=0x439d1002 rev=0x00 hdr=0x00
    class      = bridge
    subclass   = PCI-ISA
pcib3@pci0:0:20:4:   class=0x060401 card=0x00000000 chip=0x43841002 rev=0x00 hdr=0x01
    class      = bridge
    subclass   = PCI-PCI
ohci4@pci0:0:20:5:   class=0x0c0310 card=0x73021462 chip=0x43991002 rev=0x00 hdr=0x00
    class      = serial bus
    subclass   = USB
hostb1@pci0:0:24:0:  class=0x060000 card=0x00000000 chip=0x11001022 rev=0x00 hdr=0x00
    class      = bridge
    subclass   = HOST-PCI
hostb2@pci0:0:24:1:  class=0x060000 card=0x00000000 chip=0x11011022 rev=0x00 hdr=0x00
    class      = bridge
    subclass   = HOST-PCI
hostb3@pci0:0:24:2:  class=0x060000 card=0x00000000 chip=0x11021022 rev=0x00 hdr=0x00
    class      = bridge
    subclass   = HOST-PCI
hostb4@pci0:0:24:3:  class=0x060000 card=0x00000000 chip=0x11031022 rev=0x00 hdr=0x00
    class      = bridge
    subclass   = HOST-PCI
vgapci0@pci0:1:0:0:  class=0x030000 card=0xe880174b chip=0x94901002 rev=0x00 hdr=0x00
    class      = display
    subclass   = VGA
none2@pci0:1:0:1: class=0x040300 card=0xaa38174b chip=0xaa381002 rev=0x00 hdr=0x00
    class      = multimedia
re0@pci0:2:0:0:   class=0x020000 card=0x302c1462 chip=0x816810ec rev=0x02 hdr=0x00
    class      = network
    subclass   = ethernet
none3@pci0:3:3:0: class=0x040100 card=0xd6341412 chip=0x17121412 rev=0x02 hdr=0x00
    class      = multimedia
    subclass   = audio
на материнке 4 sata, 1 ide, который, похоже, должен быть ata1, которого нету.