forum.lissyara.su

И один в поле воин, если он по-русски скроен
https://forum.lissyara.su/

temp and fan статистика - DL 360 g4p, FreeBSD 8.0

https://forum.lissyara.su/viewtopic.php?f=8&t=28244

Страница 1 из 1

temp and fan статистика - DL 360 g4p, FreeBSD 8.0

Добавлено: 2010-09-02 20:41:13
cheloveka
Привет всем,

Я нашел http://markmail.org/message/r5ymaf4qu7sxhpgy, и имею подобную проблему. У меня есть server: DL 360 g4p and FreeBSD 8.0- release.
Я хочу каким-то образом неважно как получить статистику по temp and fan на этом сервере именно под FreeBSD. Самое удачное, что получилось сделать это установить hpasm 7.22 под FreeBSD 4 с включение опции в ядро compat4x, при этом запустился hpasmd, но не доступна hpasmcli. При запуске hpasmcli пишет, что:

Код: Выделить всё

HP management CLI for FreeBSD (v7.22)
Copyright 2003,2005 Hewlett-Packard Development Group, L.P.

--------------------------------------------------------------------------
NOTE: Some hpasmcli commands may not be supported on all Proliant servers.
      Type 'help' to get a list of all top level commands.
--------------------------------------------------------------------------
SetupChannel() msgget: Permission denied

ERROR: Could not communicate with hpasmd.
Please make sure the hpasmd daemon is started and running properly.

Пробовал http://lists.freebsd.org/pipermail/free ... asmcli.obj, но насколько понял что этот патч только под FreeBSD 5.
А с FreeBSD 5 с включение опции в ядро compat5x - hpasmd не запускается и ругается на:

Код: Выделить всё

# /usr/local/etc/rc.d/hpasm.sh start

/libexec/ld-elf.so.1: /usr/local/lib/compat/libpthread.so.1: version LIBTHREAD_1_0 required by /usr/sbin/hpasmd not defined
Просьба ответь если какая-то возможность побороть это дело, что снимать статистику.


Заранее благодарен за ответ.

Re: temp and fan статистика - DL 360 g4p, FreeBSD 8.0

Добавлено: 2010-09-02 21:11:55
hizel
вы ставили misc/compat ?

Re: temp and fan статистика - DL 360 g4p, FreeBSD 8.0

Добавлено: 2010-09-03 9:19:14
cheloveka
Да, пробовал все:

Код: Выделить всё

 compat4x/ 
 compat5x/
 compat6x/ 
compat7x/

Re: temp and fan статистика - DL 360 g4p, FreeBSD 8.0

Добавлено: 2010-09-03 10:10:28
hizel
а куда оно установилось?
мыслю надо для этого приложения в libmap.conf прописать нужные pthread
посмотрите man libmap.conf

Re: temp and fan статистика - DL 360 g4p, FreeBSD 8.0

Добавлено: 2010-09-03 10:49:03
Mox
а там есть ipmi?
попробуйте kldload ipmi
и посмотрите появилось ли что-нить в dmesg? типа

Код: Выделить всё

ipmi0: <IPMI System Interface> mem 0xf7ef0000-0xf7ef00ff irq 21 at device 4.6 on pci1
ipmi0: using KSC interface
ipmi1: <IPMI System Interface> on isa0
device_attach: ipmi1 attach returned 16
ipmi0: IPMI device rev. 1, firmware rev. 1.2, version 2.0
ipmi0: Number of channels 8
ipmi0: Attached watchdog
ipmi1: <IPMI System Interface> on isa0
device_attach: ipmi1 attach returned 16
если есть, то ставьте sysutils/ipmitool (ну или sysutils/freeipmi) и собирайте инфу оттуда.

Re: temp and fan статистика - DL 360 g4p, FreeBSD 8.0

Добавлено: 2010-09-03 11:39:09
cheloveka
ipmi на DL 360 g4p - нет, на DL 360 g5 - с помощью ipmi так и делал. Ставил на DL 360 g4p linux, на сайте HP есть различные утилитки - вся статистика просматривается(устройство при этом появляется /dev/hpilo). А вот на FreeBSD - утилит нет.
Пробовал также на DL 360 g4p отдельно по ILO просмотреть информацию по температуре и кулерам - ничего нет(пробовал обновлять прошивку на ILO), на DL 360 g5 - показывает.

Re: temp and fan статистика - DL 360 g4p, FreeBSD 8.0

Добавлено: 2010-09-03 12:22:05
Mox
cheloveka писал(а):ipmi на DL 360 g4p - нет, на DL 360 g5 - с помощью ipmi так и делал. Ставил на DL 360 g4p linux, на сайте HP есть различные утилитки - вся статистика просматривается(устройство при этом появляется /dev/hpilo). А вот на FreeBSD - утилит нет.
Пробовал также на DL 360 g4p отдельно по ILO просмотреть информацию по температуре и кулерам - ничего нет(пробовал обновлять прошивку на ILO), на DL 360 g5 - показывает.
да, и правда, посмотрел - нет там IPMI.

ну тогда только через сеть опрашивать iLO на предмет всяких там сенсоров
причем 2 способами:
- с помощью ssh: настраиваем ssh на iLO и лезем туда и отдаем незамысловатые команды. Но что-то наш DL360 G4 никаких сенсоров там не выдает. Вот DL360 G5 - да, но данные все равно какие-то скудные.

DL360 G4:

Код: Выделить всё

User:Admin logged-in to ilo-matrix.xx.xx(192.168.x.x)
iLO Advanced 1.94 at 12:11:27 Mar 19 2009
Server Name: MATRIX
Server Power: On

[b]</>hpiLO->[/b] show /system1/
status=0
status_tag=COMMAND COMPLETED


/system1/
  Targets
    firmware
    bootconfig1
    log1
    led1
    console1
    oemhp_vsp1
    cpu1
    cpu2
    memory1
    memory2
    memory3
    memory4
    slot1
    slot2
    powerreg_data
  Properties
    name=ProLiant DL360 G4
    number=354571GBJ51500S2
    enabledstate=enabled
    oemhp_powerreg=auto
  Verbs
    cd version exit show reset start stop


</>hpiLO->
DL360 G5:

Код: Выделить всё

login as: Admin
Admin@ilo-pys's password:
User:Admin logged-in to ilo-pys.xx.xx(192.168.x.x)
iLO 2 Advanced 1.81 at 11:05:47 Jan 15 2010
Server Name: PYS
Server Power: On

</>hpiLO-> show /system1/
status=0
status_tag=COMMAND COMPLETED


/system1/
  Targets
    firmware1
    bootconfig1
    log1
    led1
    oemhp_vsp1
    cpu1
    cpu2
    memory1
    memory2
    memory3
    memory4
    memory5
    memory6
    memory7
    memory8
    slot1
    slot2
    fan1
    fan2
    fan3
    sensor1
    sensor2
    sensor3
    sensor4
    sensor5
    sensor6
    sensor7
    sensor8
    sensor9
    powersupply1
    powersupply2
    drives
  Properties
    name=ProLiant DL360 G5
    number=CZJ801A0V4
    oemhp_server_name=PYXIS
    enabledstate=enabled
    oemhp_powerreg=dynamic
    processor_number=8
    pstate_number=2
    oemhp_pwrcap=not set
    oemhp_pwrmode=Not Supported
    oemhp_PresentPower=222 Watts
    oemhp_AveragePower=220 Watts
    oemhp_MaxPower=273 Watts
    oemhp_MinPower=219 Watts
    warning_type=warnings disabled
    warning_threshold=warnings disabled
    warning_duration=warnings disabled
    oemhp_power_micro_ver=1.0
  Verbs
    cd version exit show reset set start stop


[b]</>hpiLO->[/b] show /system1/sensor1
status=0
status_tag=COMMAND COMPLETED


/system1/sensor1
  Targets
  Properties
    DeviceID=VRM 1
    ElementName=CPU 1
    OperationalStatus=Ok
    RateUnits=Volts
    CurrentReading=N/A
    SensorType=Voltage
    HealthState=Ok
    oemhp_CautionValue=0
    oemhp_CriticalValue=0
  Verbs
    cd version exit show set


[b]</>hpiLO->[/b] show /system1/fan2
status=0
status_tag=COMMAND COMPLETED


/system1/fan2
  Targets
  Properties
    DeviceID=Fan Block 2
    ElementName=CPU
    OperationalStatus=Ok
    VariableSpeed=Yes
    DesiredSpeed=29
    HealthState=Ok
  Verbs
    cd version exit show set
- с помощью sysutils/hploscripts - это xml файлы с командами для ilo. Почти такой же способ, только вместо ssh ты будешь посылать на ilo эти файлики.

Больше я способов не знаю. hpasmd и hpasmcli стары как говно мамонта и мало где работают
Хорошо что наконец-то HP додумался и теперь ilo3 на G7 будет ipmi совместимым!

Re: temp and fan статистика - DL 360 g4p, FreeBSD 8.0

Добавлено: 2010-09-03 15:34:05
cheloveka
hizel писал(а):а куда оно установилось?
мыслю надо для этого приложения в libmap.conf прописать нужные pthread
посмотрите man libmap.conf
Прописал:

Код: Выделить всё

cat /etc/libmap.conf
libpthread.so.1 libthr.so.2
В таком случаи ругани нет, но и hpasmd при запуске молчит - в процесах не появляется. Что можно еще придумать?

Re: temp and fan статистика - DL 360 g4p, FreeBSD 8.0

Добавлено: 2010-09-03 16:14:03
hizel
а вы уверены что это то что нужно, там вместе со compat не ставится pthread?
*порыгал смотреть*
/usr/local/lib/compat/lib/compat/libpthread.so.1 есть?
может гарнее в libmap.conf

Код: Выделить всё

[путь до бинарника]
libpthread.so.1 /usr/local/lib/compat/lib/compat/libpthread.so.1
если не заработать потрусить его, прогнать через truss

Re: temp and fan статистика - DL 360 g4p, FreeBSD 8.0

Добавлено: 2010-09-06 10:20:51
cheloveka

Код: Выделить всё

/usr/local/lib/compat/lib/compat/libpthread.so.1
- нет

Код: Выделить всё

#find / -name "*libpthread.so.1*"
/usr/local/lib/compat/libpthread.so.1
truss

Код: Выделить всё

# truss hpasmd
__sysctl(0xbfbfe614,0x2,0xbfbfe61c,0xbfbfe620,0x0,0x0) = 0 (0x0)
mmap(0x0,320,PROT_READ|PROT_WRITE,MAP_ANON,-1,0x0) = 672075776 (0x280f1000)
munmap(0x280f1000,320)                           = 0 (0x0)
__sysctl(0xbfbfe678,0x2,0x280e7e9c,0xbfbfe680,0x0,0x0) = 0 (0x0)
mmap(0x0,32768,PROT_READ|PROT_WRITE,MAP_PRIVATE|MAP_ANON,-1,0x0) = 672075776 (0x280f1000)
issetugid(0x280e01a9,0xbfbfeb3c,0x104,0x0,0x0,0x0) = 0 (0x0)
open("/etc/libmap.conf",O_RDONLY,0666)           = 3 (0x3)
fstat(3,{ mode=-rw-r--r-- ,inode=94565,size=54,blksize=4096 }) = 0 (0x0)
read(3,"#[/usr/local/lib/compat/]\nlibpt"...,4096) = 54 (0x36)
read(3,0x280f5000,4096)                          = 0 (0x0)
close(3)                                         = 0 (0x0)
access("-static/libthr.so.2",0)                  ERR#2 'No such file or directory'
open("/var/run/ld-elf.so.hints",O_RDONLY,00)     = 3 (0x3)
read(3,"Ehnt\^A\0\0\0\M^@\0\0\0C\0\0\0\0"...,128) = 128 (0x80)
lseek(3,0x80,SEEK_SET)                           = 128 (0x80)
read(3,"/lib:/usr/lib:/usr/lib/compat:/u"...,67) = 67 (0x43)
close(3)                                         = 0 (0x0)
access("/lib/libthr.so.2",0)                     ERR#2 'No such file or directory'
access("/usr/lib/libthr.so.2",0)                 ERR#2 'No such file or directory'
access("/usr/lib/compat/libthr.so.2",0)          ERR#2 'No such file or directory'
access("/usr/local/lib/libthr.so.2",0)           ERR#2 'No such file or directory'
access("/usr/local/lib/compat/libthr.so.2",0)    = 0 (0x0)
mmap(0x0,36864,PROT_READ|PROT_WRITE,MAP_PRIVATE|MAP_ANON,-1,0x0) = 672108544 (0x280f9000)
open("/usr/local/lib/compat/libthr.so.2",O_RDONLY,00) = 3 (0x3)
fstat(3,{ mode=-r--r--r-- ,inode=4123744,size=69844,blksize=4096 }) = 0 (0x0)
read(3,"\^?ELF\^A\^A\^A\t\0\0\0\0\0\0\0"...,4096) = 4096 (0x1000)
mmap(0x0,73728,PROT_NONE,MAP_PRIVATE|MAP_ANON|MAP_NOCORE,-1,0x0) = 672145408 (0x28102000)
mmap(0x28102000,65536,PROT_READ|PROT_EXEC,MAP_PRIVATE|MAP_FIXED|MAP_NOCORE,3,0x0) = 672145408 (0x28102000)
mmap(0x28112000,4096,PROT_READ|PROT_WRITE,MAP_PRIVATE|MAP_FIXED,3,0x10000) = 672210944 (0x28112000)
mprotect(0x28113000,4096,PROT_READ|PROT_WRITE)   = 0 (0x0)
close(3)                                         = 0 (0x0)
access("-static/libc.so.5",0)                    ERR#2 'No such file or directory'
access("/lib/libc.so.5",0)                       ERR#2 'No such file or directory'
access("/usr/lib/libc.so.5",0)                   ERR#2 'No such file or directory'
access("/usr/lib/compat/libc.so.5",0)            ERR#2 'No such file or directory'
access("/usr/local/lib/libc.so.5",0)             ERR#2 'No such file or directory'
access("/usr/local/lib/compat/libc.so.5",0)      = 0 (0x0)
open("/usr/local/lib/compat/libc.so.5",O_RDONLY,027757763154) = 3 (0x3)
fstat(3,{ mode=-r--r--r-- ,inode=4123786,size=884972,blksize=4096 }) = 0 (0x0)
read(3,"\^?ELF\^A\^A\^A\t\0\0\0\0\0\0\0"...,4096) = 4096 (0x1000)
mmap(0x0,892928,PROT_NONE,MAP_PRIVATE|MAP_ANON|MAP_NOCORE,-1,0x0) = 672219136 (0x28114000)
mmap(0x28114000,790528,PROT_READ|PROT_EXEC,MAP_PRIVATE|MAP_FIXED|MAP_NOCORE,3,0x0) = 672219136 (0x28114000)
mmap(0x281d5000,20480,PROT_READ|PROT_WRITE,MAP_PRIVATE|MAP_FIXED,3,0xc0000) = 673009664 (0x281d5000)
mprotect(0x281da000,81920,PROT_READ|PROT_WRITE)  = 0 (0x0)
close(3)                                         = 0 (0x0)
sysarch(0xa,0xbfbfe6e0,0x280b633b,0x280e6358,0x280c8dd9,0x280e6358) = 0 (0x0)
mmap(0x0,936,PROT_READ|PROT_WRITE,MAP_ANON,-1,0x0) = 673112064 (0x281ee000)
munmap(0x281ee000,936)                           = 0 (0x0)
mmap(0x0,3768,PROT_READ|PROT_WRITE,MAP_ANON,-1,0x0) = 673112064 (0x281ee000)
munmap(0x281ee000,3768)                          = 0 (0x0)
mprotect(0x28114000,790528,PROT_READ|PROT_WRITE|PROT_EXEC) = 0 (0x0)
mmap(0x0,22024,PROT_READ|PROT_WRITE,MAP_ANON,-1,0x0) = 673112064 (0x281ee000)
munmap(0x281ee000,22024)                         = 0 (0x0)
mprotect(0x28114000,790528,PROT_READ|PROT_EXEC)  = 0 (0x0)
sigprocmask(SIG_BLOCK,SIGHUP|SIGINT|SIGQUIT|SIGKILL|SIGPIPE|SIGALRM|SIGTERM|SIGURG|SIGSTOP|SIGTSTP|SIGCONT|SIGCHLD|SIGTTIN|SIGTTOU|SIGIO|SIGXCPU|SIGXFSZ|SIGVTALRM|SIGPROF|SIGWINCH|SIGINFO|SIGUSR1|SIGUSR2,0x0) = 0 (0x0)
sigprocmask(SIG_SETMASK,0x0,0x0)                 = 0 (0x0)
sigprocmask(SIG_BLOCK,SIGHUP|SIGINT|SIGQUIT|SIGKILL|SIGPIPE|SIGALRM|SIGTERM|SIGURG|SIGSTOP|SIGTSTP|SIGCONT|SIGCHLD|SIGTTIN|SIGTTOU|SIGIO|SIGXCPU|SIGXFSZ|SIGVTALRM|SIGPROF|SIGWINCH|SIGINFO|SIGUSR1|SIGUSR2,0x0) = 0 (0x0)
sigprocmask(SIG_SETMASK,0x0,0x0)                 = 0 (0x0)
getpid(0x281d8a80,0x281120e0,0xe0,0x28112284,0x0,0x281237b4) = 1320 (0x528)
__sysctl(0xbfbfe648,0x2,0x281137b8,0xbfbfe644,0x0,0x0) = 0 (0x0)
__sysctl(0xbfbfe628,0x2,0x281eae3c,0xbfbfe624,0x0,0x0) = 0 (0x0)
readlink("/etc/malloc.conf",0xbfbfe540,63)       ERR#2 'No such file or directory'
issetugid(0xbfbfe538,0x280f3200,0x280f3200,0x0,0x28104e0e,0x280f3400) = 0 (0x0)
freebsd6_mmap(0x0,0x1000,0x3,0x1002,0xffffffff,0x0) = 673112064 (0x281ee000)
break(0x80dd000)                                 = 0 (0x0)
break(0x80de000)                                 = 0 (0x0)
sigprocmask(SIG_BLOCK,SIGHUP|SIGINT|SIGQUIT|SIGKILL|SIGPIPE|SIGALRM|SIGTERM|SIGURG|SIGSTOP|SIGTSTP|SIGCONT|SIGCHLD|SIGTTIN|SIGTTOU|SIGIO|SIGXCPU|SIGXFSZ|SIGVTALRM|SIGPROF|SIGWINCH|SIGINFO|SIGUSR1|SIGUSR2,0x0) = 0 (0x0)
sigprocmask(SIG_SETMASK,0x0,0x0)                 = 0 (0x0)
thr_self(0x80dd00c,0x2811229c,0xbfbfe688,0x28110045,0x1,0x4) = 0 (0x0)
freebsd6_mmap(0xbf9ff000,0x1000,0x0,0x1000,0xffffffff,0x0) = -1080037376 (0xbf9ff000)
break(0x80df000)                                 = 0 (0x0)
sysarch(0xa,0xbfbfe630,0x80dd000,0x80dd000,0x292,0x2811229c) = 0 (0x0)
sigprocmask(SIG_SETMASK,SIGHUP|SIGINT|SIGQUIT|SIGILL|SIGABRT|SIGEMT|SIGFPE|SIGKILL|SIGBUS|SIGSEGV|SIGSYS|SIGPIPE|SIGALRM|SIGTERM|SIGURG|SIGSTOP|SIGTSTP|SIGCONT|SIGCHLD|SIGTTIN|SIGTTOU|SIGIO|SIGXCPU|SIGXFSZ|SIGVTALRM|SIGPROF|SIGWINCH|SIGINFO|SIGUSR1|SIGUSR2,0x0) = 0 (0x0)
sigaction(32,{ 0x2810ba7c SA_RESTART|SA_SIGINFO ss_t },0x0) = 0 (0x0)
sigprocmask(SIG_SETMASK,0x0,0x0)                 = 0 (0x0)
sigprocmask(SIG_BLOCK,SIGHUP|SIGINT|SIGQUIT|SIGKILL|SIGPIPE|SIGALRM|SIGTERM|SIGURG|SIGSTOP|SIGTSTP|SIGCONT|SIGCHLD|SIGTTIN|SIGTTOU|SIGIO|SIGXCPU|SIGXFSZ|SIGVTALRM|SIGPROF|SIGWINCH|SIGINFO|SIGUSR1|SIGUSR2,0x0) = 0 (0x0)
sigprocmask(SIG_SETMASK,0x0,0x0)                 = 0 (0x0)
getuid(0xbfbfeb90,0x3,0x3,0x280f3400,0x280e6358,0x0) = 0 (0x0)
stat("/var/run/hpasmd.pid",0xbfbfebf8)           ERR#2 'No such file or directory'
mkdir("/cpqhealth",0644)                         ERR#17 'File exists'
lstat("/cpqhealth/casr",{ mode=crw-r--r-- ,inode=79,size=0,blksize=4096 }) = 0 (0x0)
unlink("/cpqhealth/casr")                        = 0 (0x0)
mknod("/cpqhealth/casr",020644,134898656)        = 0 (0x0)
lstat("/cpqhealth/cecc",{ mode=crw-r--r-- ,inode=80,size=0,blksize=4096 }) = 0 (0x0)
unlink("/cpqhealth/cecc")                        = 0 (0x0)
mknod("/cpqhealth/cecc",020644,134898656)        = 0 (0x0)
lstat("/cpqhealth/ccsm",{ mode=crw-r--r-- ,inode=81,size=0,blksize=4096 }) = 0 (0x0)
unlink("/cpqhealth/ccsm")                        = 0 (0x0)
mknod("/cpqhealth/ccsm",020644,134898656)        = 0 (0x0)
lstat("/cpqhealth/cevt",{ mode=crw-r--r-- ,inode=82,size=0,blksize=4096 }) = 0 (0x0)
unlink("/cpqhealth/cevt")                        = 0 (0x0)
mknod("/cpqhealth/cevt",020644,134898656)        = 0 (0x0)
lstat("/cpqhealth/cdt",{ mode=crw-r--r-- ,inode=83,size=0,blksize=4096 }) = 0 (0x0)
unlink("/cpqhealth/cdt")                         = 0 (0x0)
mknod("/cpqhealth/cdt",020644,134898656)         = 0 (0x0)
lstat("/cpqhealth/crom",{ mode=crw-r--r-- ,inode=84,size=0,blksize=4096 }) = 0 (0x0)
unlink("/cpqhealth/crom")                        = 0 (0x0)
mknod("/cpqhealth/crom",020644,134898656)        = 0 (0x0)
open("/.hpshm_keyfile",O_CREAT,0700)             = 3 (0x3)
close(3)                                         = 0 (0x0)
stat("/.hpshm_keyfile",{ mode=-rwx------ ,inode=85,size=0,blksize=4096 }) = 0 (0x0)
semget(0x73570055,0x1,0x380,0x80a5dd0,0x1000,0x0) = 65536 (0x10000)
compat7.__semctl(0x10000,0x0,0x8,0xbfbfeb80,0x1,0x80b4a84) = 0 (0x0)
__sysctl(0xbfbfeb18,0x2,0xbfbfeb20,0xbfbfeb14,0x80addd7,0xe) = 0 (0x0)
__sysctl(0xbfbfeb20,0x2,0x80dad90,0x80b46f0,0x0,0x0) = 0 (0x0)
sigaction(SIGHUP,{ SIG_IGN 0x0 ss_t },{ SIG_DFL 0x0 ss_t }) = 0 (0x0)
sigprocmask(SIG_BLOCK,SIGHUP|SIGINT|SIGQUIT|SIGABRT|SIGEMT|SIGKILL|SIGSYS|SIGPIPE|SIGALRM|SIGTERM|SIGURG|SIGSTOP|SIGTSTP|SIGCONT|SIGCHLD|SIGTTIN|SIGTTOU|SIGIO|SIGXCPU|SIGXFSZ|SIGVTALRM|SIGPROF|SIGWINCH|SIGINFO|SIGUSR1|SIGUSR2,0x0) = 0 (0x0)
fork(0x80dd000,0xbfbfebb8,0x280b5629,0x28108a56,0x281137b0,0xbfbfeb20) = 1321 (0x529)
sigprocmask(SIG_SETMASK,0x0,0x0)                 = 0 (0x0)
process exit, rval = 0

Re: temp and fan статистика - DL 360 g4p, FreeBSD 8.0

Добавлено: 2010-09-06 11:27:32
hizel
ну ок я опечатался

Код: Выделить всё

[путь до бинарника]
libpthread.so.1 /usr/local/lib/compat/lib/compat/libpthread.so.1
путь до бинарника обязателен, иначе все может сломаться

Re: temp and fan статистика - DL 360 g4p, FreeBSD 8.0

Добавлено: 2010-09-06 13:28:07
cheloveka
правильно ли я понял:

Код: Выделить всё

#cat /etc/libmap.conf
[ /usr/sbin/hpasmd ]
libpthread.so.1 /usr/local/lib/compat/libpthread.so.1

#/usr/sbin/hpasmd
/libexec/ld-elf.so.1: Shared object "/usr/local/lib/compat/libpthread.so.1" not found, required by "hpasmd"

Re: temp and fan статистика - DL 360 g4p, FreeBSD 8.0

Добавлено: 2010-09-06 13:55:55
hizel
ну да, только не понятно почему он не находит файлик, ведь он же есть?

Re: temp and fan статистика - DL 360 g4p, FreeBSD 8.0

Добавлено: 2010-09-06 14:42:27
Mox
может надо убрать пробелы между квадратной скобкой и буквами и получится вот так?

Код: Выделить всё

[/usr/sbin/hpasmd]
libpthread.so.1 /usr/local/lib/compat/libpthread.so.1

Re: temp and fan статистика - DL 360 g4p, FreeBSD 8.0

Добавлено: 2010-09-06 14:46:52
cheloveka
Похоже не находит:

Код: Выделить всё

truss /usr/sbin/hpasmd
__sysctl(0xbfbfe604,0x2,0xbfbfe60c,0xbfbfe610,0x0,0x0) = 0 (0x0)
mmap(0x0,320,PROT_READ|PROT_WRITE,MAP_ANON,-1,0x0) = 672075776 (0x280f1000)
munmap(0x280f1000,320)                           = 0 (0x0)
__sysctl(0xbfbfe668,0x2,0x280e7e9c,0xbfbfe670,0x0,0x0) = 0 (0x0)
mmap(0x0,32768,PROT_READ|PROT_WRITE,MAP_PRIVATE|MAP_ANON,-1,0x0) = 672075776 (0x280f1000)
issetugid(0x280e01a9,0xbfbfeb2c,0x104,0x0,0x0,0x0) = 0 (0x0)
open("/etc/libmap.conf",O_RDONLY,0666)           = 3 (0x3)
fstat(3,{ mode=-rw-r--r-- ,inode=94565,size=75,blksize=4096 }) = 0 (0x0)
read(3,"[ /usr/sbin/hpasmd ]\nlibpthread"...,4096) = 75 (0x4b)
read(3,0x280f5000,4096)                          = 0 (0x0)
close(3)                                         = 0 (0x0)
access("-static//usr/local/lib/compat/libpthread.so.1",0) ERR#2 'No such file or directory'
open("/var/run/ld-elf.so.hints",O_RDONLY,05002742353) = 3 (0x3)
read(3,"Ehnt\^A\0\0\0\M^@\0\0\0C\0\0\0\0"...,128) = 128 (0x80)
mmap(0x0,36864,PROT_READ|PROT_WRITE,MAP_PRIVATE|MAP_ANON,-1,0x0) = 672108544 (0x280f9000)
lseek(3,0x80,SEEK_SET)                           = 128 (0x80)
read(3,"/lib:/usr/lib:/usr/lib/compat:/u"...,67) = 67 (0x43)
close(3)                                         = 0 (0x0)
access("/lib//usr/local/lib/compat/libpthread.so.1",0) ERR#2 'No such file or directory'
access("/usr/lib//usr/local/lib/compat/libpthread.so.1",0) ERR#2 'No such file or directory'
access("/usr/lib/compat//usr/local/lib/compat/libpthread.so.1",0) ERR#2 'No such file or directory'
access("/usr/local/lib//usr/local/lib/compat/libpthread.so.1",0) ERR#2 'No such file or directory'
access("/usr/local/lib/compat//usr/local/lib/compat/libpthread.so.1",0) ERR#2 'No such file or directory'
access("/lib//usr/local/lib/compat/libpthread.so.1",0) ERR#2 'No such file or directory'
access("/usr/lib//usr/local/lib/compat/libpthread.so.1",0) ERR#2 'No such file or directory'
/libexec/ld-elf.so.1: write(2,"/libexec/ld-elf.so.1: ",22)               = 22 (0x16)
Shared object "/usr/local/lib/compat/libpthread.so.1" not found, required by "hpasmd"write(2,"Shared object "/usr/local/lib/co"...,85) = 85 (0x55)

write(2,"\n",1)                                  = 1 (0x1)
process exit, rval = 1

А вот так:

Код: Выделить всё

#cat /etc/libmap.conf
[ /usr/sbin/hpasmd ]
libpthread.so.1 libpthread.so.1

Код: Выделить всё

#/usr/sbin/hpasmd
/libexec/ld-elf.so.1: /usr/local/lib/compat/libpthread.so.1: version LIBTHREAD_1_0 required by /usr/sbin/hpasmd not defined

Код: Выделить всё

#truss  /usr/sbin/hpasmd
__sysctl(0xbfbfe604,0x2,0xbfbfe60c,0xbfbfe610,0x0,0x0) = 0 (0x0)
mmap(0x0,320,PROT_READ|PROT_WRITE,MAP_ANON,-1,0x0) = 672075776 (0x280f1000)
munmap(0x280f1000,320)                           = 0 (0x0)
__sysctl(0xbfbfe668,0x2,0x280e7e9c,0xbfbfe670,0x0,0x0) = 0 (0x0)
mmap(0x0,32768,PROT_READ|PROT_WRITE,MAP_PRIVATE|MAP_ANON,-1,0x0) = 672075776 (0x280f1000)
issetugid(0x280e01a9,0xbfbfeb2c,0x104,0x0,0x0,0x0) = 0 (0x0)
open("/etc/libmap.conf",O_RDONLY,0666)           = 3 (0x3)
fstat(3,{ mode=-rw-r--r-- ,inode=94565,size=53,blksize=4096 }) = 0 (0x0)
read(3,"[ /usr/sbin/hpasmd ]\nlibpthread"...,4096) = 53 (0x35)
read(3,0x280f5000,4096)                          = 0 (0x0)
close(3)                                         = 0 (0x0)
access("-static/libpthread.so.1",0)              ERR#2 'No such file or directory'
open("/var/run/ld-elf.so.hints",O_RDONLY,05002742353) = 3 (0x3)
read(3,"Ehnt\^A\0\0\0\M^@\0\0\0C\0\0\0\0"...,128) = 128 (0x80)
lseek(3,0x80,SEEK_SET)                           = 128 (0x80)
read(3,"/lib:/usr/lib:/usr/lib/compat:/u"...,67) = 67 (0x43)
close(3)                                         = 0 (0x0)
access("/lib/libpthread.so.1",0)                 ERR#2 'No such file or directory'
access("/usr/lib/libpthread.so.1",0)             ERR#2 'No such file or directory'
access("/usr/lib/compat/libpthread.so.1",0)      ERR#2 'No such file or directory'
access("/usr/local/lib/libpthread.so.1",0)       ERR#2 'No such file or directory'
access("/usr/local/lib/compat/libpthread.so.1",0) = 0 (0x0)
mmap(0x0,36864,PROT_READ|PROT_WRITE,MAP_PRIVATE|MAP_ANON,-1,0x0) = 672108544 (0x280f9000)
open("/usr/local/lib/compat/libpthread.so.1",O_RDONLY,00) = 3 (0x3)
fstat(3,{ mode=-r--r--r-- ,inode=4123840,size=285352,blksize=4096 }) = 0 (0x0)
read(3,"\^?ELF\^A\^A\^A\t\0\0\0\0\0\0\0"...,4096) = 4096 (0x1000)
mmap(0x0,69632,PROT_NONE,MAP_PRIVATE|MAP_ANON|MAP_NOCORE,-1,0x0) = 672145408 (0x28102000)
mmap(0x28102000,57344,PROT_READ|PROT_EXEC,MAP_PRIVATE|MAP_FIXED|MAP_NOCORE,3,0x0) = 672145408 (0x28102000)
mmap(0x28110000,4096,PROT_READ|PROT_WRITE,MAP_PRIVATE|MAP_FIXED,3,0xe000) = 672202752 (0x28110000)
mprotect(0x28111000,8192,PROT_READ|PROT_WRITE)   = 0 (0x0)
close(3)                                         = 0 (0x0)
access("-static/libc.so.5",0)                    ERR#2 'No such file or directory'
access("/lib/libc.so.5",0)                       ERR#2 'No such file or directory'
access("/usr/lib/libc.so.5",0)                   ERR#2 'No such file or directory'
access("/usr/lib/compat/libc.so.5",0)            ERR#2 'No such file or directory'
access("/usr/local/lib/libc.so.5",0)             ERR#2 'No such file or directory'
access("/usr/local/lib/compat/libc.so.5",0)      = 0 (0x0)
open("/usr/local/lib/compat/libc.so.5",O_RDONLY,027757763134) = 3 (0x3)
fstat(3,{ mode=-r--r--r-- ,inode=4123786,size=884972,blksize=4096 }) = 0 (0x0)
read(3,"\^?ELF\^A\^A\^A\t\0\0\0\0\0\0\0"...,4096) = 4096 (0x1000)
mmap(0x0,892928,PROT_NONE,MAP_PRIVATE|MAP_ANON|MAP_NOCORE,-1,0x0) = 672215040 (0x28113000)
mmap(0x28113000,790528,PROT_READ|PROT_EXEC,MAP_PRIVATE|MAP_FIXED|MAP_NOCORE,3,0x0) = 672215040 (0x28113000)
mmap(0x281d4000,20480,PROT_READ|PROT_WRITE,MAP_PRIVATE|MAP_FIXED,3,0xc0000) = 673005568 (0x281d4000)
mprotect(0x281d9000,81920,PROT_READ|PROT_WRITE)  = 0 (0x0)
close(3)                                         = 0 (0x0)
/libexec/ld-elf.so.1: write(2,"/libexec/ld-elf.so.1: ",22)               = 22 (0x16)
/usr/local/lib/compat/libpthread.so.1: version LIBTHREAD_1_0 required by /usr/sbin/hpasmd not definedwrite(2,"/usr/local/lib/compat/libpthread"...,101) = 101 (0x65)

write(2,"\n",1)                                  = 1 (0x1)
process exit, rval = 1
А вот так:

Код: Выделить всё

#cat /etc/libmap.conf
[ /usr/sbin/hpasmd ]
libpthread.so.1   libpthread.so.2

# /usr/sbin/hpasmd
#Пусто
#ps ax | grep hpasmd
 1838   0  R+     0:00.00 grep hpasmd

 truss /usr/sbin/hpasmd
__sysctl(0xbfbfe5e4,0x2,0xbfbfe5ec,0xbfbfe5f0,0x0,0x0) = 0 (0x0)
mmap(0x0,320,PROT_READ|PROT_WRITE,MAP_ANON,-1,0x0) = 672075776 (0x280f1000)
munmap(0x280f1000,320)                           = 0 (0x0)
__sysctl(0xbfbfe648,0x2,0x280e7e9c,0xbfbfe650,0x0,0x0) = 0 (0x0)
mmap(0x0,32768,PROT_READ|PROT_WRITE,MAP_PRIVATE|MAP_ANON,-1,0x0) = 672075776 (0x280f1000)
issetugid(0x280e01a9,0xbfbfeb0c,0x104,0x0,0x0,0x0) = 0 (0x0)
open("/etc/libmap.conf",O_RDONLY,0666)           = 3 (0x3)
fstat(3,{ mode=-rw-r--r-- ,inode=94565,size=56,blksize=4096 }) = 0 (0x0)
read(3,"[ /usr/sbin/hpasmd ]\nlibpthread"...,4096) = 56 (0x38)
read(3,0x280f5000,4096)                          = 0 (0x0)
close(3)                                         = 0 (0x0)
access("-static/libpthread.so.2",0)              ERR#2 'No such file or directory'
open("/var/run/ld-elf.so.hints",O_RDONLY,05002742353) = 3 (0x3)
read(3,"Ehnt\^A\0\0\0\M^@\0\0\0C\0\0\0\0"...,128) = 128 (0x80)
lseek(3,0x80,SEEK_SET)                           = 128 (0x80)
read(3,"/lib:/usr/lib:/usr/lib/compat:/u"...,67) = 67 (0x43)
close(3)                                         = 0 (0x0)
access("/lib/libpthread.so.2",0)                 ERR#2 'No such file or directory'
access("/usr/lib/libpthread.so.2",0)             ERR#2 'No such file or directory'
access("/usr/lib/compat/libpthread.so.2",0)      ERR#2 'No such file or directory'
access("/usr/local/lib/libpthread.so.2",0)       ERR#2 'No such file or directory'
access("/usr/local/lib/compat/libpthread.so.2",0) = 0 (0x0)
mmap(0x0,36864,PROT_READ|PROT_WRITE,MAP_PRIVATE|MAP_ANON,-1,0x0) = 672108544 (0x280f9000)
open("/usr/local/lib/compat/libpthread.so.2",O_RDONLY,00) = 3 (0x3)
fstat(3,{ mode=-r--r--r-- ,inode=4123744,size=69844,blksize=4096 }) = 0 (0x0)
read(3,"\^?ELF\^A\^A\^A\t\0\0\0\0\0\0\0"...,4096) = 4096 (0x1000)
mmap(0x0,73728,PROT_NONE,MAP_PRIVATE|MAP_ANON|MAP_NOCORE,-1,0x0) = 672145408 (0x28102000)
mmap(0x28102000,65536,PROT_READ|PROT_EXEC,MAP_PRIVATE|MAP_FIXED|MAP_NOCORE,3,0x0) = 672145408 (0x28102000)
mmap(0x28112000,4096,PROT_READ|PROT_WRITE,MAP_PRIVATE|MAP_FIXED,3,0x10000) = 672210944 (0x28112000)
mprotect(0x28113000,4096,PROT_READ|PROT_WRITE)   = 0 (0x0)
close(3)                                         = 0 (0x0)
access("-static/libc.so.5",0)                    ERR#2 'No such file or directory'
access("/lib/libc.so.5",0)                       ERR#2 'No such file or directory'
access("/usr/lib/libc.so.5",0)                   ERR#2 'No such file or directory'
access("/usr/lib/compat/libc.so.5",0)            ERR#2 'No such file or directory'
access("/usr/local/lib/libc.so.5",0)             ERR#2 'No such file or directory'
access("/usr/local/lib/compat/libc.so.5",0)      = 0 (0x0)
open("/usr/local/lib/compat/libc.so.5",O_RDONLY,027757763074) = 3 (0x3)
fstat(3,{ mode=-r--r--r-- ,inode=4123786,size=884972,blksize=4096 }) = 0 (0x0)
read(3,"\^?ELF\^A\^A\^A\t\0\0\0\0\0\0\0"...,4096) = 4096 (0x1000)
mmap(0x0,892928,PROT_NONE,MAP_PRIVATE|MAP_ANON|MAP_NOCORE,-1,0x0) = 672219136 (0x28114000)
mmap(0x28114000,790528,PROT_READ|PROT_EXEC,MAP_PRIVATE|MAP_FIXED|MAP_NOCORE,3,0x0) = 672219136 (0x28114000)
mmap(0x281d5000,20480,PROT_READ|PROT_WRITE,MAP_PRIVATE|MAP_FIXED,3,0xc0000) = 673009664 (0x281d5000)
mprotect(0x281da000,81920,PROT_READ|PROT_WRITE)  = 0 (0x0)
close(3)                                         = 0 (0x0)
sysarch(0xa,0xbfbfe6b0,0x280b633b,0x280e6358,0x280c8dd9,0x280e6358) = 0 (0x0)
mmap(0x0,936,PROT_READ|PROT_WRITE,MAP_ANON,-1,0x0) = 673112064 (0x281ee000)
munmap(0x281ee000,936)                           = 0 (0x0)
mmap(0x0,3768,PROT_READ|PROT_WRITE,MAP_ANON,-1,0x0) = 673112064 (0x281ee000)
munmap(0x281ee000,3768)                          = 0 (0x0)
mprotect(0x28114000,790528,PROT_READ|PROT_WRITE|PROT_EXEC) = 0 (0x0)
mmap(0x0,22024,PROT_READ|PROT_WRITE,MAP_ANON,-1,0x0) = 673112064 (0x281ee000)
munmap(0x281ee000,22024)                         = 0 (0x0)
mprotect(0x28114000,790528,PROT_READ|PROT_EXEC)  = 0 (0x0)
sigprocmask(SIG_BLOCK,SIGHUP|SIGINT|SIGQUIT|SIGKILL|SIGPIPE|SIGALRM|SIGTERM|SIGURG|SIGSTOP|SIGTSTP|SIGCONT|SIGCHLD|SIGTTIN|SIGTTOU|SIGIO|SIGXCPU|SIGXFSZ|SIGVTALRM|SIGPROF|SIGWINCH|SIGINFO|SIGUSR1|SIGUSR2,0x0) = 0 (0x0)
sigprocmask(SIG_SETMASK,0x0,0x0)                 = 0 (0x0)
sigprocmask(SIG_BLOCK,SIGHUP|SIGINT|SIGQUIT|SIGKILL|SIGPIPE|SIGALRM|SIGTERM|SIGURG|SIGSTOP|SIGTSTP|SIGCONT|SIGCHLD|SIGTTIN|SIGTTOU|SIGIO|SIGXCPU|SIGXFSZ|SIGVTALRM|SIGPROF|SIGWINCH|SIGINFO|SIGUSR1|SIGUSR2,0x0) = 0 (0x0)
sigprocmask(SIG_SETMASK,0x0,0x0)                 = 0 (0x0)
getpid(0x281d8a80,0x281120e0,0xe0,0x28112284,0x0,0x281237b4) = 1847 (0x737)
__sysctl(0xbfbfe618,0x2,0x281137b8,0xbfbfe614,0x0,0x0) = 0 (0x0)
__sysctl(0xbfbfe5f8,0x2,0x281eae3c,0xbfbfe5f4,0x0,0x0) = 0 (0x0)
readlink("/etc/malloc.conf",0xbfbfe510,63)       ERR#2 'No such file or directory'
issetugid(0xbfbfe508,0x280f3200,0x280f3200,0x0,0x28104e0e,0x280f3400) = 0 (0x0)
freebsd6_mmap(0x0,0x1000,0x3,0x1002,0xffffffff,0x0) = 673112064 (0x281ee000)
break(0x80dd000)                                 = 0 (0x0)
break(0x80de000)                                 = 0 (0x0)
sigprocmask(SIG_BLOCK,SIGHUP|SIGINT|SIGQUIT|SIGKILL|SIGPIPE|SIGALRM|SIGTERM|SIGURG|SIGSTOP|SIGTSTP|SIGCONT|SIGCHLD|SIGTTIN|SIGTTOU|SIGIO|SIGXCPU|SIGXFSZ|SIGVTALRM|SIGPROF|SIGWINCH|SIGINFO|SIGUSR1|SIGUSR2,0x0) = 0 (0x0)
sigprocmask(SIG_SETMASK,0x0,0x0)                 = 0 (0x0)
thr_self(0x80dd00c,0x2811229c,0xbfbfe658,0x28110045,0x1,0x4) = 0 (0x0)
freebsd6_mmap(0xbf9ff000,0x1000,0x0,0x1000,0xffffffff,0x0) = -1080037376 (0xbf9ff000)
break(0x80df000)                                 = 0 (0x0)
sysarch(0xa,0xbfbfe600,0x80dd000,0x80dd000,0x292,0x2811229c) = 0 (0x0)
sigprocmask(SIG_SETMASK,SIGHUP|SIGINT|SIGQUIT|SIGILL|SIGABRT|SIGEMT|SIGFPE|SIGKILL|SIGBUS|SIGSEGV|SIGSYS|SIGPIPE|SIGALRM|SIGTERM|SIGURG|SIGSTOP|SIGTSTP|SIGCONT|SIGCHLD|SIGTTIN|SIGTTOU|SIGIO|SIGXCPU|SIGXFSZ|SIGVTALRM|SIGPROF|SIGWINCH|SIGINFO|SIGUSR1|SIGUSR2,0x0) = 0 (0x0)
sigaction(32,{ 0x2810ba7c SA_RESTART|SA_SIGINFO ss_t },0x0) = 0 (0x0)
sigprocmask(SIG_SETMASK,0x0,0x0)                 = 0 (0x0)
sigprocmask(SIG_BLOCK,SIGHUP|SIGINT|SIGQUIT|SIGKILL|SIGPIPE|SIGALRM|SIGTERM|SIGURG|SIGSTOP|SIGTSTP|SIGCONT|SIGCHLD|SIGTTIN|SIGTTOU|SIGIO|SIGXCPU|SIGXFSZ|SIGVTALRM|SIGPROF|SIGWINCH|SIGINFO|SIGUSR1|SIGUSR2,0x0) = 0 (0x0)
sigprocmask(SIG_SETMASK,0x0,0x0)                 = 0 (0x0)
getuid(0xbfbfeb60,0x3,0x3,0x280f3400,0x280e6358,0x0) = 0 (0x0)
stat("/var/run/hpasmd.pid",0xbfbfebc8)           ERR#2 'No such file or directory'
mkdir("/cpqhealth",0644)                         ERR#17 'File exists'
lstat("/cpqhealth/casr",{ mode=crw-r--r-- ,inode=79,size=0,blksize=4096 }) = 0 (0x0)
unlink("/cpqhealth/casr")                        = 0 (0x0)
mknod("/cpqhealth/casr",020644,134898656)        = 0 (0x0)
lstat("/cpqhealth/cecc",{ mode=crw-r--r-- ,inode=80,size=0,blksize=4096 }) = 0 (0x0)
unlink("/cpqhealth/cecc")                        = 0 (0x0)
mknod("/cpqhealth/cecc",020644,134898656)        = 0 (0x0)
lstat("/cpqhealth/ccsm",{ mode=crw-r--r-- ,inode=81,size=0,blksize=4096 }) = 0 (0x0)
unlink("/cpqhealth/ccsm")                        = 0 (0x0)
mknod("/cpqhealth/ccsm",020644,134898656)        = 0 (0x0)
lstat("/cpqhealth/cevt",{ mode=crw-r--r-- ,inode=82,size=0,blksize=4096 }) = 0 (0x0)
unlink("/cpqhealth/cevt")                        = 0 (0x0)
mknod("/cpqhealth/cevt",020644,134898656)        = 0 (0x0)
lstat("/cpqhealth/cdt",{ mode=crw-r--r-- ,inode=83,size=0,blksize=4096 }) = 0 (0x0)
unlink("/cpqhealth/cdt")                         = 0 (0x0)
mknod("/cpqhealth/cdt",020644,134898656)         = 0 (0x0)
lstat("/cpqhealth/crom",{ mode=crw-r--r-- ,inode=84,size=0,blksize=4096 }) = 0 (0x0)
unlink("/cpqhealth/crom")                        = 0 (0x0)
mknod("/cpqhealth/crom",020644,134898656)        = 0 (0x0)
open("/.hpshm_keyfile",O_CREAT,0700)             = 3 (0x3)
close(3)                                         = 0 (0x0)
stat("/.hpshm_keyfile",{ mode=-rwx------ ,inode=85,size=0,blksize=4096 }) = 0 (0x0)
semget(0x73570055,0x1,0x380,0x80a5dd0,0x1000,0x0) = 65536 (0x10000)
compat7.__semctl(0x10000,0x0,0x8,0xbfbfeb50,0x1,0x80b4a84) = 0 (0x0)
__sysctl(0xbfbfeae8,0x2,0xbfbfeaf0,0xbfbfeae4,0x80addd7,0xe) = 0 (0x0)
__sysctl(0xbfbfeaf0,0x2,0x80dad90,0x80b46f0,0x0,0x0) = 0 (0x0)
sigaction(SIGHUP,{ SIG_IGN 0x0 ss_t },{ SIG_DFL 0x0 ss_t }) = 0 (0x0)
sigprocmask(SIG_BLOCK,SIGHUP|SIGINT|SIGQUIT|SIGABRT|SIGEMT|SIGKILL|SIGSYS|SIGPIPE|SIGALRM|SIGTERM|SIGURG|SIGSTOP|SIGTSTP|SIGCONT|SIGCHLD|SIGTTIN|SIGTTOU|SIGIO|SIGXCPU|SIGXFSZ|SIGVTALRM|SIGPROF|SIGWINCH|SIGINFO|SIGUSR1|SIGUSR2,0x0) = 0 (0x0)
fork(0x80dd000,0xbfbfeb88,0x280b5629,0x28108a56,0x281137b0,0xbfbfeaf0) = 1848 (0x738)
sigprocmask(SIG_SETMASK,0x0,0x0)                 = 0 (0x0)
process exit, rval = 0

Re: temp and fan статистика - DL 360 g4p, FreeBSD 8.0

Добавлено: 2010-09-13 15:51:28
cheloveka
Вопрос, так и остался открытым может, есть у кого какие еще идеи по мониторингу температуры и кулеров под FreeBSD 8.0 на DL 360 g4p.
Часовой пояс: UTC+03:00
Страница 1 из 1
Powered by phpBB® Forum Software © phpBB Limited
https://www.phpbb.com/