Страности с dhcp-сервером
Добавлено: 2007-12-24 1:48:59
Установил с портов dhcp-сервер. Да, он работает, но как то странно взаимодействует к примеру с тем же апачем...дЛЯ
после этого получаю следующее
как это понимать? последняя сточка
это допущеная мною ошибка в rc.conf(установил фтп-сервер и не верно прописал). с этого делаю вывод, что каким то образом при попытке остановить апач перезапускается ДХЦП-сервер, который в свою очередь перечитывает rc.conf.
о том чо апач таки не остановился я заикатся не буду в этой теме( /usr/local/sbin/apachectl stop - так работает).
при запуска/остановке mysql - таже картина.
да, подняты три ната для своих нужд, почему ругается что он занят, никак не пойму....
Код: Выделить всё
/usr/local/etc/rc.d/apache22 stop
Код: Выделить всё
delete net default
add net default: gateway 192.168.0.1
route: writing to routing socket: File exists
add net 192.168.100.0: gateway 192.168.100.100: route already in table
route: writing to routing socket: File exists
add net 10.18.0.2: gateway 10.18.0.1: route already in table
Internet Systems Consortium DHCP Server V3.0.5
Copyright 2004-2006 Internet Systems Consortium.
All rights reserved.
For info, please visit http://www.isc.org/sw/dhcp/
Wrote 0 deleted host decls to leases file.
Wrote 0 new dynamic host decls to leases file.
Wrote 2 leases to leases file.
Listening on BPF/rl2/00:02:44:9a:f2:d5/192.168.200/24
Sending on BPF/rl2/00:02:44:9a:f2:d5/192.168.200/24
No subnet declaration for rl1 (192.168.300.1).
** Ignoring requests on rl1. If this is not what
you want, please write a subnet declaration
in your dhcpd.conf file for the network segment
to which interface rl1 is attached. **
No subnet declaration for rl0 (192.168.100.1).
** Ignoring requests on rl0. If this is not what
you want, please write a subnet declaration
in your dhcpd.conf file for the network segment
to which interface rl0 is attached. **
No subnet declaration for vr0 (192.168.0.2).
** Ignoring requests on vr0. If this is not what
you want, please write a subnet declaration
in your dhcpd.conf file for the network segment
to which interface vr0 is attached. **
Can't bind to dhcp address: Address already in use
Please make sure there is no other dhcp server
running and that there's no entry for dhcp or
bootp in /etc/inetd.conf. Also make sure you
are not running HP JetAdmin software, which
includes a bootp server.
natd: Unable to bind divert socket.: Address already in use
natd: Unable to bind divert socket.: Address already in use
natd: Unable to bind divert socket.: Address already in use
pure-ftpd_enable=YES: not found
Код: Выделить всё
pure-ftpd_enable=YES: not found
о том чо апач таки не остановился я заикатся не буду в этой теме( /usr/local/sbin/apachectl stop - так работает).
при запуска/остановке mysql - таже картина.
Код: Выделить всё
Address already in use