Проблема с make config в портах

[Gamerman]

В какой-то момент возникла следующая проблема:
делаю make config, "ОК" и никакой реакции. После КТРЛ-С, в каталоге порта возникает файл с именем -t типа:
cat ./-t
"SQUID_IPV6" "SQUID_SNMP" "SQUID_HTCP" "SQUID_WCCP" "SQUID_IDENT" "SQUID_KQUEUE"

Такое ощущение, что это ключ, а сам файл не открывается.

Как пофиксить?

[Хостинг HostFood.ru]

Тарифы на хостинг в России, от 12 рублей: https://www.host-food.ru/tariffs/hosting/
Тарифы на виртуальные сервера (VPS/VDS/KVM) в РФ, от 189 руб.: https://www.host-food.ru/tariffs/virtualny-server-vps/
Выделенные сервера, Россия, Москва, от 2000 рублей (HP Proliant G5, Intel Xeon E5430 (2.66GHz, Quad-Core, 12Mb), 8Gb RAM, 2x300Gb SAS HDD, P400i, 512Mb, BBU):
https://www.host-food.ru/tariffs/vydelennyi-server-ds/
Недорогие домены в популярных зонах: https://www.host-food.ru/domains/

[paradox]

потому что уже настроено конфиг
смотрите по форуму уже был ответ какудалить предыдущие настройки конфиг

[Gamerman]

потому что уже настроено конфиг

Кем настроено? Если мною, то, после изменения настроек ситуация аналогичная. Раньше такого не было.
Кроме того, нормально работающая система после нажатия на кнопку "ОК" должна что-то делать, а не останавливаться (виснуть).

[paradox]

а вы уверены что оно ничего не делает?
может оно розархивирует архив в 300 метров а у вас комп слабенький

[Gamerman]

а вы уверены что оно ничего не делает?
может оно розархивирует архив в 300 метров а у вас комп слабенький

Уверен.
1. Окно конфига висит на экране.
2. Комп не слабый.
3. Появляется странный файл, раньше его не было.
Мне кажется, что какая-то проблема с файлом, куда должны записываться параметры.

Проблема на всех портах.

PS. Да, собственно, что оно может разархивировать после конфигурации? Установка-то не начата?

[paradox]

скажите версию портов от какого числа
и имя порта какой устанавливаете

может кто то будет проходить мимо и опровергнет или подтвердит даный глюк

[Gamerman]

Версия портов самая свежая делаю через portsnap
FreeBSD-7.2

Поковырял немного и увидел такое:

? ?[X] SQUID_IDENT Enable ident (RFC 931) lookups ? ?
???????v(+)???????????????????????????????????????????????????????????
? [ OK ] Cancel ?
??????????????????????????????????????????????????????????????????????

^Crm: illegal option -- t
usage: rm [-f | -i] [-dIPRrvW] file ...
unlink file

То есть, команда шлет неверную опцию при удалении.

[paradox]

я говорю уточните какой именно пакет устанавливаете

[Gamerman]

я говорю уточните какой именно пакет устанавливаете

Пример был для /ports/www/squid31
Tо же самoе и при /ports/misc/mc

? ? [X] UTF8 Build with UTF8 support ? ?
? ? [X] SLANG Build with SLang library ? ?
? ? [X] ICONV Build with iconv recoding ? ?
? ? [X] NLS Build with NLS support ? ?
? ? [X] EDIT Build with internal editor ? ?
? ? [ ] X11 Build with X11 library ? ?
? ? [X] SUBSHELL Build with subshell support ? ?
? ? [X] SAMBA Build with Samba support ? ?
? ? ? ?
? ? ? ?
? ? ? ?
? ? ? ?
? ? ? ?
? ? ? ?
? ? ? ?
??????????????????????????????????????????????????????????????????????
? [ OK ] Cancel ?
??????????????????????????????????????????????????????????????????????

^Crm: illegal option -- t
usage: rm [-f | -i] [-dIPRrvW] file ...
unlink file

[paradox]

предполагаю что сисьему нужно тоже обновить
если оно не понимает опции -t для rm
ксожалению подвердить немогу я не юзаю 7

[Gamerman]

предполагаю что сисьему нужно тоже обновить
если оно не понимает опции -t для rm
ксожалению подвердить немогу я не юзаю 7

Хм... А вот это может быть. В 8-ке есть такой ключ?

[paradox]

пока незнаю

paradox@hosting[15:21:24]~/cvsup> csup cvsupfiles.8_0
Connected to 72.233.193.64
Rejected by server: Access limit exceeded; try again later
Will retry at 15:26:40

обновиться скажу

[paradox]

нет опции -t в 8

[Gamerman]

Да уж... И что же делать?

[MASiK]

Скинька сюда

Код: Выделить всё

cat /etc/make.conf

Так же вспоминай что делал с системой, если он у тебя это ошибку на всех портах выдаёт значит дело не в портах

В противном случае делай Порт Снап, потом

Код: Выделить всё

mergemaster

И смотри где чё не так

P.S. или схитри )))))

Код: Выделить всё

echo "alias rm -t rm -f" >> ~/.cshrc

[Gamerman]

Код: Выделить всё

 cat /etc/make.conf
# $FreeBSD: src/share/examples/etc/make.conf,v 1.279 2007/01/17 12:43:06 des Exp $
#
# NOTE:  Please would any committer updating this file also update the
# make.conf(5) manual page, if necessary, which is located in
# src/share/man/man5/make.conf.5.
#
# /etc/make.conf, if present, will be read by make (see
# /usr/share/mk/sys.mk).  It allows you to override macro definitions
# to make without changing your source tree, or anything the source
# tree installs.
#
# This file must be in valid Makefile syntax.
#
# There are additional things you can put into /etc/make.conf.
# You have to find those in the Makefiles and documentation of
# the source tree.
#
# Note, that you should not set MAKEOBJDIRPREFIX or MAKEOBJDIR
# from make.conf (or as command line variables to make).
# Both variables are environment variables for make and must be used as:
#
# env MAKEOBJDIRPREFIX=/big/directory make
#
#
# The CPUTYPE variable controls which processor should be targeted for
# generated code.  This controls processor-specific optimizations in
# certain code (currently only OpenSSL) as well as modifying the value
# of CFLAGS to contain the appropriate optimization directive to gcc.
# The automatic setting of CFLAGS may be overridden using the
# NO_CPU_CFLAGS variable below.
# Currently the following CPU types are recognized:
#   Intel x86 architecture:
#       (AMD CPUs)      opteron athlon64 athlon-mp athlon-xp athlon-4
#                       athlon-tbird athlon k8 k6-3 k6-2 k6 k5
#       (Intel CPUs)    core2 core nocona pentium4m pentium4 prescott
#                       pentium3m pentium3 pentium-m pentium2
#                       pentiumpro pentium-mmx pentium i486 i386
#       (Via CPUs)      c3 c3-2
#   Alpha/AXP architecture: ev67 ev6 pca56 ev56 ev5 ev45 ev4
#   AMD64 architecture: opteron, athlon64, nocona, prescott, core2
#   Intel ia64 architecture: itanium2, itanium
#
# (?= allows to buildworld for a different CPUTYPE.)
#
#CPUTYPE?=pentium3
#NO_CPU_CFLAGS=         # Don't add -march=<cpu> to CFLAGS automatically
#NO_CPU_COPTFLAGS=      # Don't add -march=<cpu> to COPTFLAGS automatically
#
# CFLAGS controls the compiler settings used when compiling C code.
# Note that optimization settings other than -O and -O2 are not recommended
# or supported for compiling the world or the kernel - please revert any
# nonstandard optimization settings to "-O" or "-O2 -fno-strict-aliasing"
# before submitting bug reports without patches to the developers.
#
# Compiling with -fstrict-aliasing optimization breaks some [notable] ports.
# GCC turns on -fstrict-aliasing optimization at all levels above -O[1], so
# explicitly turn it off when using compiling with the -O2 optimization level.
#
#CFLAGS= -O2 -fno-strict-aliasing -pipe
#
# CXXFLAGS controls the compiler settings used when compiling C++ code.
# Note that CXXFLAGS is initially set to the value of CFLAGS.  If you wish
# to add to CXXFLAGS value, "+=" must be used rather than "=".  Using "="
# alone will remove the often needed contents of CFLAGS from CXXFLAGS.
#
#CXXFLAGS+= -fconserve-space
#
# MAKE_SHELL controls the shell used internally by make(1) to process the
# command scripts in makefiles.  Three shells are supported, sh, ksh, and
# csh.  Using sh is most common, and advised.  Using ksh *may* work, but is
# not guaranteed to.  Using csh is absurd.  The default is to use sh.
#
#MAKE_SHELL?=sh
#
# BDECFLAGS are a set of gcc warning settings that Bruce Evans has suggested
# for use in developing FreeBSD and testing changes.  They can be used by
# putting "CFLAGS+=${BDECFLAGS}" in /etc/make.conf.  -Wconversion is not
# included here due to compiler bugs, e.g., mkdir()'s mode_t argument.
#
#BDECFLAGS=     -W -Wall -ansi -pedantic -Wbad-function-cast -Wcast-align \
#               -Wcast-qual -Wchar-subscripts -Winline \
#               -Wmissing-prototypes -Wnested-externs -Wpointer-arith \
#               -Wredundant-decls -Wshadow -Wstrict-prototypes -Wwrite-strings
#
# To compile just the kernel with special optimizations, you should use
# this instead of CFLAGS (which is not applicable to kernel builds anyway).
# There is very little to gain by using higher optimization levels, and doing
# so can cause problems.
#
#COPTFLAGS= -O -pipe
#
# Compare before install
#INSTALL=install -C
#
# Mtree will follow symlinks
#MTREE_FOLLOWS_SYMLINKS= -L
#
# To enable installing ssh(1) with the setuid bit turned on
#ENABLE_SUID_SSH=
#
# To enable installing newgrp(1) with the setuid bit turned on.
# Without the setuid bit, newgrp cannot change users' groups.
#ENABLE_SUID_NEWGRP=
#
# To avoid building various parts of the base system:
#NO_MODULES=            # do not build modules with the kernel
#NO_SHARE=              # do not go into the share subdir
#NO_SHARED=             # build /bin and /sbin statically linked (bad idea)
#
# Variables that control how ppp(8) is built.
#PPP_NO_NAT=            # do not build with NAT support (see make.conf(5))
#PPP_NO_NETGRAPH=       # do not build with Netgraph support
#PPP_NO_RADIUS=         # do not build with RADIUS support
#PPP_NO_SUID=           # build with normal permissions
#
#TRACEROUTE_NO_IPSEC=   # do not build traceroute(8) with IPSEC support
#
# To build sys/modules when building the world (our old way of doing things)
#MODULES_WITH_WORLD=    # do not build modules when building kernel
#
# The list of modules to build instead of all of them.
#MODULES_OVERRIDE=      linux ipfw
#
# The list of modules to never build, applied *after* MODULES_OVERRIDE.
#WITHOUT_MODULES=       bktr plip
#
# If you do not want unformatted manual pages to be compressed
# when they are installed:
#
#NO_MANCOMPRESS=
#
#
# Default format for system documentation, depends on your printer.
# Set this to "ascii" for simple printers or screen
#
#PRINTERDEVICE= ps
#
#
# How long to wait for a console keypress before booting the default kernel.
# This value is approximately in milliseconds. Keypresses are accepted by the
# BIOS before booting from disk, making it possible to give custom boot
# parameters even when this is set to 0.
#
#BOOTWAIT=0
#BOOTWAIT=30000
#
# By default, the system will always use the keyboard/video card as system
# console.  However, the boot blocks may be dynamically configured to use a
# serial port in addition to or instead of the keyboard/video console.
#
# By default we use COM1 as our serial console port *if* we're going to use
# a serial port as our console at all.  Alter as necessary.
#
#   COM1: = 0x3F8, COM2: = 0x2F8, COM3: = 0x3E8, COM4: = 0x2E8
#
#BOOT_COMCONSOLE_PORT=  0x3F8
#
# The default serial console speed is 9600.  Set the speed to a larger value
# for better interactive response.
#
#BOOT_COMCONSOLE_SPEED= 115200
#
# By default the 'pxeboot' loader retrieves the kernel via NFS.  Defining
# this and recompiling /usr/src/sys/boot will cause it to retrieve the kernel
# via TFTP.  This allows pxeboot to load a custom BOOTP diskless kernel yet
# still mount the server's '/' (i.e. rather than load the server's kernel).
#
#LOADER_TFTP_SUPPORT= YES
#
#
# Kerberos 5 su (k5su)
# If you want to use the k5su utility, define this to have it installed
# set-user-ID.
#ENABLE_SUID_K5SU=
#
#
# CVSup update flags.  Edit SUPFILE settings to reflect whichever distribution
# file(s) you use on your site (see /usr/share/examples/cvsup/README for more
# information on CVSup and these files).  To use, do "make update" in /usr/src.
#
#SUP_UPDATE=
#
#SUP=            /usr/bin/csup
#SUPFLAGS=       -g -L 2
#SUPHOST=        cvsup.uk.FreeBSD.org
#SUPFILE=        /usr/share/examples/cvsup/standard-supfile
#PORTSSUPFILE=   /usr/share/examples/cvsup/ports-supfile
#DOCSUPFILE=     /usr/share/examples/cvsup/doc-supfile
#
# top(1) uses a hash table for the user names.  The size of this hash
# can be tuned to match the number of local users.  The table size should
# be a prime number approximately twice as large as the number of lines in
# /etc/passwd.  The default number is 20011.
#
#TOP_TABLE_SIZE= 101
#
# Documentation
#
# The list of languages and encodings to build and install
#
#DOC_LANG=      en_US.ISO8859-1 ru_RU.KOI8-R
#
#
# sendmail
#
# The following sets the default m4 configuration file to use at
# install time.  Use with caution as a make install will overwrite
# any existing /etc/mail/sendmail.cf.  Note that SENDMAIL_CF is now
# deprecated.  The value should be a fully qualified path name.
#
#SENDMAIL_MC=/etc/mail/myconfig.mc
#
# The following sets the default m4 configuration file for mail
# submission to use at install time.  Use with caution as a make
# install will overwrite any existing /etc/mail/submit.cf.  The
# value should be a fully qualified path name.
#
#SENDMAIL_SUBMIT_MC=/etc/mail/mysubmit.mc
#
# If you need to build additional .cf files during a make buildworld,
# include the full paths to the .mc files in SENDMAIL_ADDITIONAL_MC.
#
#SENDMAIL_ADDITIONAL_MC=/etc/mail/foo.mc /etc/mail/bar.mc
#
# The following overrides the default location for the m4 configuration
# files used to build a .cf file from a .mc file.
#
#SENDMAIL_CF_DIR=/usr/local/share/sendmail/cf
#
# Setting the following variable modifies the flags passed to m4 when
# building a .cf file from a .mc file.  It can be used to enable
# features disabled by default.
#
#SENDMAIL_M4_FLAGS=
#
# Setting the following variables modifies the build environment for
# sendmail and its related utilities. For example, SASL support can be
# added with settings such as:
#
#    with SASLv1:
#       SENDMAIL_CFLAGS=-I/usr/local/include/sasl1 -DSASL
#       SENDMAIL_LDFLAGS=-L/usr/local/lib
#       SENDMAIL_LDADD=-lsasl
#
#    with SASLv2:
#       SENDMAIL_CFLAGS=-I/usr/local/include -DSASL=2
#       SENDMAIL_LDFLAGS=-L/usr/local/lib
#       SENDMAIL_LDADD=-lsasl2
#
# Note: If you are using Cyrus SASL with other applications which require
#       access to the sasldb file, you should add the following to your
#       sendmail.mc file:
#
#       define(`confDONT_BLAME_SENDMAIL',`GroupReadableSASLDBFile')
#
#SENDMAIL_CFLAGS=
#SENDMAIL_LDFLAGS=
#SENDMAIL_LDADD=
#SENDMAIL_DPADD=
#
# Setting SENDMAIL_SET_USER_ID will install the sendmail binary as a
# set-user-ID root binary instead of a set-group-ID smmsp binary and will
# prevent the installation of /etc/mail/submit.cf.
# This is a deprecated mode of operation.  See etc/mail/README for more
# information.
#
#SENDMAIL_SET_USER_ID=
#
# The permissions to use on alias and map databases generated using
# /etc/mail/Makefile.  Defaults to 0640.
#
#SENDMAIL_MAP_PERMS=
# added by use.perl 2008-09-21 11:58:33
PERL_VER=5.8.8
PERL_VERSION=5.8.8

Проблема думаю, что не в портах, посколько на другой машине с подобной системой таких проблем нет. Либо какой-то файл битый, либо я что-то где-то не то написал.

Я и так смотрел еще.

Код: Выделить всё

 make -n config
(optionsdir=/var/db/ports/mc/options; optionsdir=${optionsdir%/*};  /bin/mkdir -p ${optionsdir} 2> /dev/null) ||  (echo "===> Cannot create ${optionsdir}, check permissions"; exit 1)
if [ -e /var/db/ports/mc/options ]; then  . /var/db/ports/mc/options;  fi;  set -- UTF8         "Build with UTF8 support" on  SLANG             "Build with SLang library" on  ICONV            "Build with iconv recoding" on  NLS            "Build with NLS support" on  EDIT                "Build with internal editor" on  X11            "Build with X11 library" off  SUBSHELL  "Build with subshell support" on  SAMBA         "Build with Samba support" on XXX;  while [ $# -gt 3 ]; do  OPTIONSLIST="${OPTIONSLIST} $1";  defaultval=$3;  withvar=WITH_$1;  withoutvar=WITHOUT_$1;  withval=$(eval echo $\{${withvar}\});  withoutval=$(eval echo $\{${withoutvar}\});  if [ ! -z "${withval}" ]; then  val=on;  elif [ ! -z "${withoutval}" ]; then  val=off;  else  val=$3;  fi;  DEFOPTIONS="${DEFOPTIONS} $1 \"$2\" ${val}";  shift 3;  done;  TMPOPTIONSFILE=$(mktemp -t portoptions);  trap "/bin/rm -f ${TMPOPTIONSFILE}; exit 1" 1 2 3 5 10 13 15;  /bin/sh -c "/usr/bin/dialog --checklist \"Options for mc 4.6.2\" 21 70 15 ${DEFOPTIONS} 2> ${TMPOPTIONSFILE}";  status=$?;  if [ ${status} -ne 0 ] ; then  /bin/rm -f ${TMPOPTIONSFILE};  echo "===> Options unchanged";  exit 0;  fi;  if [ ! -e  ]; then  echo "===> No user-specified options to save for mc-4.6.2";  exit 0;  fi;  SELOPTIONS=$(/bin/cat ${TMPOPTIONSFILE});  /bin/rm -f ${TMPOPTIONSFILE};  TMPOPTIONSFILE=$(mktemp -t portoptions);  trap "/bin/rm -f ${TMPOPTIONSFILE}; exit 1" 1 2 3 5 10 13 15;  echo "# This file is auto-generated by 'make config'." > ${TMPOPTIONSFILE};  echo "# No user-servicable parts inside!" >> ${TMPOPTIONSFILE};  echo "# Options for mc-4.6.2" >> ${TMPOPTIONSFILE};  echo "_OPTIONS_READ=mc-4.6.2" >> ${TMPOPTIONSFILE};  for i in ${OPTIONSLIST}; do  echo ${SELOPTIONS} | /usr/bin/grep -qw ${i};  if [ $? -eq 0 ]; then  echo WITH_${i}=true >> ${TMPOPTIONSFILE};  else  echo WITHOUT_${i}=true >> ${TMPOPTIONSFILE};  fi;  done;  if [ `/usr/bin/id -u` != 0 -a "x" = "x" ]; then  echo "===>  Switching to root credentials to write /var/db/ports/mc/options";  /usr/bin/su root -c "/bin/cat ${TMPOPTIONSFILE} > /var/db/ports/mc/options";  echo "===>  Returning to user credentials";  else  /bin/cat ${TMPOPTIONSFILE} > /var/db/ports/mc/options;  fi;  /bin/rm -f ${TMPOPTIONSFILE}

[Gamerman]

И так, после долгих разборов и поисков, проблему решил. Как всегда оказалось, она не там где искали
Проблема была в том, что файл mktemp был в директории /usr/bin и в директории /usr/local/bin. При чем во второй старый и не поддерживал ключ -t.

Почему они разные и там и там, еще предстоит разобраться.

Виной случившемуся замена строк
#set path = (/sbin /bin /usr/sbin /usr/bin /usr/games /usr/local/sbin /usr/local/bin $HOME/bin)
set path = (/usr/local/sbin /usr/local/bin /usr/sbin /usr/bin /sbin /bin $HOME/bin)
в файле /root/.cshrc