1. Заставил bios правильно увидеть объем карты / отобразить в post screen
2. Потом ставил... порты реально долго распаковывались
- Разметка - под рутовый раздел почти весь объем карты, остаток под swap (торопился)
- Загружается шустро, несмотря на то что generic и стаааарая машинка (хотя usb на плате уже есть) ))
1. Внешнее питание
2. 5v
3. Master
Код: Выделить всё
Copyright (c) 1992-2008 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 7.0-RELEASE #0: Sun Feb 24 19:59:52 UTC 2008
root@logan.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC
Preloaded elf kernel "/boot/kernel/kernel" at 0xc0d08000.
Calibrating clock(s) ... i8254 clock: 1193274 Hz
CLK_USE_I8254_CALIBRATION not specified - using default frequency
Timecounter "i8254" frequency 1193182 Hz quality 0
Calibrating TSC clock ... TSC clock: 200456524 Hz
CPU: AMD-K6tm w/ multimedia extensions (200.46-MHz 586-class CPU)
Origin = "AuthenticAMD" Id = 0x562 Stepping = 2
Features=0x8001bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,MMX>
AMD Features=0x400<<b10>>
Data TLB: 128 entries, 2-way associative
Instruction TLB: 64 entries, 1-way associative
L1 data cache: 32 kbytes, 32 bytes/line, 2 lines/tag, 2-way associative
L1 instruction cache: 32 kbytes, 32 bytes/line, 2 lines/tag, 2-way associative
Write Allocate Enable Limit: 64M bytes
Write Allocate 15-16M bytes: Enable
Hardware Write Allocate Control: Disable
real memory = 67108864 (64 MB)
Physical memory chunk(s):
0x0000000000001000 - 0x000000000009efff, 647168 bytes (158 pages)
0x0000000000100000 - 0x00000000003fffff, 3145728 bytes (768 pages)
0x0000000001028000 - 0x0000000003e9efff, 48721920 bytes (11895 pages)
avail memory = 51691520 (49 MB)
bios32: Found BIOS32 Service Directory header at 0xc00fad40
bios32: Entry = 0xfb1c0 (c00fb1c0) Rev = 0 Len = 1
pcibios: PCI BIOS entry at 0xf0000+0xb1f0
pnpbios: Found PnP BIOS data at 0xc00fbda0
pnpbios: Entry = f0000:bdc8 Rev = 1.0
Other BIOS signatures found:
ath_rate: version 1.2 <SampleRate bit-rate selection algorithm>
wlan_amrr: <AMRR Transmit Rate Control Algorithm>
wlan: <802.11 Link Layer>
null: <null device, zero device>
random: <entropy source, Software, Yarrow>
nfslock: pseudo-device
kbd: new array size 4
kbd1 at kbdmux0
io: <I/O>
mem: <memory>
ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
hptrr: HPT RocketRAID controller driver v1.1 (Feb 24 2008 19:59:27)
npx0: INT 16 interface
cpu0 on motherboard
pci_open(1): mode 1 addr port (0x0cf8) is 0x80003b48
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 [class=060000] [hdr=00] is there (id=05971106)
pcibios: BIOS version 2.10
pcib0: <Host to PCI bridge> pcibus 0 on motherboard
pir0: <PCI Interrupt Routing Table: 4 Entries> on motherboard
$PIR: Links after initial probe:
Link IRQ Rtd Ref IRQs
0x1 255 N 3 3 4 5 7 10 11 12 14 15
0x2 255 N 3 3 4 5 7 10 11 12 14 15
0x3 255 N 3 3 4 5 7 10 11 12 14 15
0x5 255 N 3 3 4 5 7 10 11 12 14 15
$PIR: Found matching pin for 0.9.INTA at func 0: 10
$PIR: Links after initial IRQ discovery:
Link IRQ Rtd Ref IRQs
0x1 255 N 3 3 4 5 7 10 11 12 14 15
0x2 10 Y 3 3 4 5 7 10 11 12 14 15
0x3 255 N 3 3 4 5 7 10 11 12 14 15
0x5 255 N 3 3 4 5 7 10 11 12 14 15
$PIR: IRQs used by BIOS: 10
$PIR: Interrupt Weights:
[ 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 ]
[ 0 0 0 0 0 0 0 0 0 0 3 0 0 0 0 0 ]
pci0: <PCI bus> on pcib0
pci0: domain=0, physical bus=0
found-> vendor=0x1106, dev=0x0597, revid=0x04
domain=0, bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[10]: type Prefetchable Memory, range 32, base 0xe0000000, size 25, enabled
found-> vendor=0x1106, dev=0x8597, revid=0x00
domain=0, bus=0, slot=1, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0007, statreg=0x0220, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x04 (1000 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1106, dev=0x0586, revid=0x41
domain=0, bus=0, slot=7, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x008f, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1106, dev=0x0571, revid=0x06
domain=0, bus=0, slot=7, func=1
class=01-01-8a, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[20]: type I/O Port, range 32, base 0xe000, size 4, enabled
found-> vendor=0x1106, dev=0x3038, revid=0x02
domain=0, bus=0, slot=7, func=2
class=0c-03-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0200, cachelnsz=8 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=d, irq=11
map[20]: type I/O Port, range 32, base 0xe400, size 5, enabled
$PIR: No matching entry for 0.7.INTD
found-> vendor=0x1106, dev=0x3040, revid=0x10
domain=0, bus=0, slot=7, func=3
class=06-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0000, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x10ec, dev=0x8139, revid=0x10
domain=0, bus=0, slot=9, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0007, statreg=0x0290, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x20 (8000 ns), maxlat=0x40 (16000 ns)
intpin=a, irq=10
powerspec 2 supports D0 D1 D2 D3 current D0
map[10]: type I/O Port, range 32, base 0xe800, size 8, enabled
map[14]: type Memory, range 32, base 0xe2000000, size 8, enabled
$PIR: 0:9 INTA routed to irq 10
agp0: <VIA 82C597 (Apollo VP3) host to PCI bridge> on hostb0
hostb0: Reserved 0x2000000 bytes for rid 0x10 type 3 at 0xe0000000
agp0: allocating GATT for aperture of size 256M
agp0: aperture size is 256M
pcib1: <PCI-PCI bridge> at device 1.0 on pci0
pcib1: domain 0
pcib1: secondary bus 1
pcib1: subordinate bus 1
pcib1: I/O decode 0xd000-0xdfff
pcib1: no prefetched decode
pci1: <PCI bus> on pcib1
pci1: domain=0, physical bus=1
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <VIA 82C586B UDMA33 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xe000-0xe00f at device 7.1 on pci0
atapci0: Reserved 0x10 bytes for rid 0x20 type 4 at 0xe000
ata0: <ATA channel 0> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x10 type 4 at 0x1f0
atapci0: Reserved 0x1 bytes for rid 0x14 type 4 at 0x3f6
ata0: reset tp1 mask=03 ostat0=50 ostat1=00
ata0: stat0=0x80 err=0x80 lsb=0x80 msb=0x80
ata0: stat0=0x50 err=0x01 lsb=0x00 msb=0x00
ata0: stat1=0x00 err=0xff lsb=0xff msb=0xff
ata0: reset tp2 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata0: [MPSAFE]
ata0: [ITHREAD]
ata1: <ATA channel 1> on atapci0
atapci0: Reserved 0x8 bytes for rid 0x18 type 4 at 0x170
atapci0: Reserved 0x1 bytes for rid 0x1c type 4 at 0x376
ata1: reset tp1 mask=03 ostat0=51 ostat1=00
ata1: stat0=0x80 err=0x80 lsb=0x80 msb=0x80
ata1: stat0=0x80 err=0x80 lsb=0x80 msb=0x80
ata1: stat0=0x80 err=0x80 lsb=0x80 msb=0x80
ata1: stat0=0x80 err=0x80 lsb=0x80 msb=0x80
ata1: stat0=0x00 err=0x01 lsb=0x14 msb=0xeb
ata1: stat1=0x00 err=0x00 lsb=0x14 msb=0xeb
ata1: reset tp2 stat0=00 stat1=00 devices=0x4<ATAPI_MASTER>
ata1: [MPSAFE]
ata1: [ITHREAD]
uhci0: <VIA 83C572 USB controller> port 0xe400-0xe41f irq 11 at device 7.2 on pci0
uhci0: Reserved 0x20 bytes for rid 0x20 type 4 at 0xe400
uhci0: [GIANT-LOCKED]
uhci0: [ITHREAD]
usb0: <VIA 83C572 USB controller> on uhci0
usb0: USB revision 1.0
uhub0: <VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 2 ports with 2 removable, self powered
pci0: <bridge> at device 7.3 (no driver attached)
re0: Reserved 0x100 bytes for rid 0x10 type 4 at 0xe800
rl0: <RealTek 8139 10/100BaseTX> port 0xe800-0xe8ff mem 0xe2000000-0xe20000ff irq 10 at device 9.0 on pci0
miibus0: <MII bus> on rl0
rlphy0: <RealTek internal media interface> PHY 0 on miibus0
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
rl0: bpf attached
rl0: Ethernet address: 00:02:44:06:83:21
rl0: [MPSAFE]
rl0: [ITHREAD]
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
unknown: status reg test failed ff
ex_isa_identify()
ata: ata0 already exists; skipping it
ata: ata1 already exists; skipping it
pnp_identify: Trying Read_Port at 203
pnp_identify: Trying Read_Port at 243
pnp_identify: Trying Read_Port at 283
pnp_identify: Trying Read_Port at 2c3
pnp_identify: Trying Read_Port at 303
pnp_identify: Trying Read_Port at 343
pnp_identify: Trying Read_Port at 383
pnp_identify: Trying Read_Port at 3c3
PNP Identify complete
pnpbios: 12 devices, largest 98 bytes
PNP0200: adding dma mask 0x10
PNP0200: adding io range 0-0xf, size=0x10, align=0
PNP0200: adding io range 0x81-0x83, size=0x3, align=0
PNP0200: adding io range 0x87-0x87, size=0x1, align=0
PNP0200: adding io range 0x89-0x8b, size=0x3, align=0
PNP0200: adding io range 0x8f-0x91, size=0x3, align=0
PNP0200: adding io range 0xc0-0xdf, size=0x20, align=0
pnpbios: handle 1 device ID PNP0200 (0002d041)
PNP0100: adding irq mask 0x1
PNP0100: adding io range 0x40-0x43, size=0x4, align=0
pnpbios: handle 2 device ID PNP0100 (0001d041)
PNP0b00: adding irq mask 0x100
PNP0b00: adding io range 0x70-0x71, size=0x2, align=0
pnpbios: handle 3 device ID PNP0b00 (000bd041)
PNP0303: adding irq mask 0x2
PNP0303: adding io range 0x60-0x60, size=0x1, align=0
PNP0303: adding io range 0x64-0x64, size=0x1, align=0
pnpbios: handle 4 device ID PNP0303 (0303d041)
PNP0800: adding io range 0x61-0x61, size=0x1, align=0
pnpbios: handle 5 device ID PNP0800 (0008d041)
PNP0c04: adding irq mask 0x2000
PNP0c04: adding io range 0xf0-0xff, size=0x10, align=0
pnpbios: handle 6 device ID PNP0c04 (040cd041)
PNP0c01: adding fixed memory32 range 0xe0000-0xfffff, size=0x20000
PNP0c01: adding fixed memory32 range 0-0x9ffff, size=0xa0000
PNP0c01: adding fixed memory32 range 0xfffe0000-0xffffffff, size=0x20000
PNP0c01: adding fixed memory32 range 0x100000-0x3ffffff, size=0x3f00000
PNP0c01: adding fixed memory32 range 0xc8000-0xc9fff, size=0x2000
pnpbios: handle 7 device ID PNP0c01 (010cd041)
PNP0a03: adding io range 0x4d0-0x4d1, size=0x2, align=0
PNP0a03: adding io range 0xcf8-0xcff, size=0x8, align=0
PNP0a03: adding io range 0x480-0x48f, size=0x10, align=0
PNP0a03: adding io range 0x5000-0x507f, size=0x80, align=0
PNP0a03: adding io range 0x5080-0x50ff, size=0x80, align=0
pnpbios: handle 8 device ID PNP0a03 (030ad041)
PNP0501: adding irq mask 0x10
PNP0501: adding io range 0x3f8-0x3ff, size=0x8, align=0
pnpbios: handle 9 device ID PNP0501 (0105d041)
PNP0401: adding dma mask 0x8
PNP0401: adding irq mask 0x80
PNP0401: adding io range 0x378-0x37f, size=0x8, align=0
PNP0401: adding io range 0x778-0x77b, size=0x4, align=0
pnpbios: handle 10 device ID PNP0401 (0104d041)
PNP0501: adding irq mask 0x8
PNP0501: adding io range 0x2f8-0x2ff, size=0x8, align=0
pnpbios: handle 11 device ID PNP0501 (0105d041)
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xc9fff pnpid ORM0000 on isa0
adv0: not probed (disabled)
aha0: not probed (disabled)
aic0: not probed (disabled)
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x0, flags:0x3d0000
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: current command byte:0065
psm0: failed to reset the aux device.
bt0: not probed (disabled)
cs0: not probed (disabled)
ed0: not probed (disabled)
fdc0 failed to probe at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fe0: not probed (disabled)
ie0: not probed (disabled)
le0: not probed (disabled)
ppc0: parallel port found at 0x378
ppc0: using extended I/O port range
ppc0: ECP SPP ECP+EPP SPP
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/16 bytes threshold
ppbus0: <Parallel port bus> on ppc0
ppbus0: [MPSAFE]
ppbus0: [ITHREAD]
plip0: <PLIP network interface> on ppbus0
plip0: bpf attached
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
ppc0: [GIANT-LOCKED]
ppc0: [ITHREAD]
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd1, terminal emulator: sc (syscons terminal)
sio0: irq maps: 0x1 0x11 0x1 0x1
sio0: irq maps: 0x1 0x11 0x1 0x1
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio0: [FILTER]
sio1: irq maps: 0x1 0x9 0x1 0x1
sio1: irq maps: 0x1 0x9 0x1 0x1
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
sio1: [FILTER]
sio2: not probed (disabled)
sio3: not probed (disabled)
sn0: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
vt0: not probed (disabled)
isa_probe_children: probing PnP devices
unknown: <PNP0303> can't assign resources (port)
unknown: <PNP0303> at port 0x60 pnpid PNP0303 on isa0
unknown: <PNP0800> failed to probe at port 0x61 pnpid PNP0800 on isa0
unknown: <PNP0c01> can't assign resources (memory)
unknown: <PNP0c01> at iomem 0xe0000-0xfffff,0-0x9ffff pnpid PNP0c01 on isa0
unknown: <PNP0501> can't assign resources (port)
unknown: <PNP0501> at port 0x3f8-0x3ff pnpid PNP0501 on isa0
unknown: <PNP0401> can't assign resources (port)
unknown: <PNP0401> at port 0x378-0x37f pnpid PNP0401 on isa0
unknown: <PNP0501> can't assign resources (port)
unknown: <PNP0501> at port 0x2f8-0x2ff pnpid PNP0501 on isa0
Device configuration finished.
procfs registered
Timecounter "TSC" frequency 200456524 Hz quality 800
Timecounters tick every 1.000 msec
lo0: bpf attached
hptrr: no controller detected.
ata0-master: pio=PIO4 wdma=UNSUPPORTED udma=UNSUPPORTED cable=40 wire
ad0: setting PIO4 on 82C586B chip
ad0: 1946MB <TOSHIBA THNCF2G04QG 3.00> at ata0-master PIO4
ad0: 3985632 sectors [3954C/16H/63S] 1 sectors/interrupt 1 depth queue
GEOM: new disk ad0
ad0: VIA check1 failed
ad0: Adaptec check1 failed
ad0: LSI (v3) check1 failed
ad0: LSI (v2) check1 failed
ad0: FreeBSD check1 failed
ata1-master: pio=PIO3 wdma=WDMA2 udma=UNSUPPORTED cable=40 wire
acd0: setting PIO3 on 82C586B chip
acd0: <E285XA/1.00> CDROM drive at ata1 as master
acd0: read 1377KB/s (1377KB/s), 240KB buffer, PIO3
acd0: Reads: CDDA
acd0: Writes:
acd0: Audio: play, 255 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: no/blank disc
ATA PseudoRAID loaded
Trying to mount root from ufs:/dev/ad0s1a
start_init: trying /sbin/init
Loading configuration files.
kernel dumps on /dev/ad0s1b
Entropy harvesting:
interrupts
ethernet
point_to_point
kickstart
.
swapon: adding /dev/ad0s1b as swap device
Starting file system checks:
/dev/ad0s1a: FILE SYSTEM CLEAN; SKIPPING CHECKS
/dev/ad0s1a: clean, 423646 free (2766 frags, 52610 blocks, 0.3% fragmentation)
Setting hostuuid: bccb572f-5e7a-11dd-8a89-2b0c749a9771.
Setting hostid: 0x914455fb.
Mounting local file systems:
.
Setting hostname: EWVIA..
net.inet6.ip6.auto_linklocal:
1
->
0
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x3
inet6 ::1 prefixlen 128
inet 127.0.0.1 netmask 0xff000000
rl0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
options=8<VLAN_MTU>
ether 00:02:44:06:83:21
inet 192.168.0.196 netmask 0xffffff00 broadcast 192.168.0.255
media: Ethernet autoselect (none)
status: no carrier
add net default: gateway 192.168.0.197
Additional routing options:
IP gateway=YES
.
Starting devd.
Additional IP options:
.
Mounting NFS file systems:
.
Creating and/or trimming log files:
.
Starting syslogd.
Checking for core dump on /dev/ad0s1b...
savecore: no dumps found
ELF ldconfig path: /lib /usr/lib /usr/lib/compat
a.out ldconfig path: /usr/lib/aout /usr/lib/compat/aout
Initial i386 initialization:
.
Additional ABI support:
.
Clearing /tmp (X related).
Starting local daemons:
.
Updating motd
.
Mounting late file systems:
.
Configuring syscons:
blanktime
.
Generating public/private rsa1 key pair.
Your identification has been saved in /etc/ssh/ssh_host_key.
Your public key has been saved in /etc/ssh/ssh_host_key.pub.
The key fingerprint is:
9b:82:25:6b:d8:e1:84:b6:29:78:19:cc:a9:07:03:9c root@EWVIA.
Generating public/private dsa key pair.
Your identification has been saved in /etc/ssh/ssh_host_dsa_key.
Your public key has been saved in /etc/ssh/ssh_host_dsa_key.pub.
The key fingerprint is:
c3:9b:01:ae:03:b1:f1:48:10:18:07:59:20:84:d8:d8 root@EWVIA.
Generating public/private rsa key pair.
Your identification has been saved in /etc/ssh/ssh_host_rsa_key.
Your public key has been saved in /etc/ssh/ssh_host_rsa_key.pub.
The key fingerprint is:
08:a6:22:09:7c:8b:a4:f2:a5:63:87:52:8b:da:49:3c root@EWVIA.
Starting sshd.
Starting cron.
Local package initialization:
.
Starting background file system checks in 60 seconds.
Mon Aug 4 14:07:41 MSD 2008
Aug 4 14:08:01 EWVIA login: ROOT LOGIN (root) ON ttyv0
В отпуске ) в сентябре серьезно займусь...
)
Установка тоже долго шла, но в моём случае дело явно не в приводе. Ибо на этой же самой машине пробовал ставить и на жёсткий. Дело явно в карточке. Особенно тяжко ставились порты. 
