Проблема в том, что по дефолту ставиться именно та , что на HDMI и звука соответственно со второй нет.
Как переназначить я незнаю
Помогите настроить звук.
тест звукавая проходит
Код: Выделить всё
cat filename > /dev/dsp1.0
Код: Выделить всё
cat /dev/sndstat
FreeBSD Audio Driver (newpcm: 64bit 2009061500/amd64)
Installed devices:
pcm0: <HDA ATI RS690/780 HDMI PCM #0 Digital> at cad 0 nid 1 on hdac0 kld snd_hda [MPSAFE] (1p:1v/0r:0v channels simplex default)
pcm1: <HDA Realtek ALC885 PCM #0 Analog> at cad 0 nid 1 on hdac1 kld snd_hda [MPSAFE] (1p:3v/1r:3v channels duplex)
pcm2: <HDA Realtek ALC885 PCM #1 Analog> at cad 0 nid 1 on hdac1 kld snd_hda [MPSAFE] (1p:1v/1r:1v channels duplex)
pcm3: <HDA Realtek ALC885 PCM #2 Digital> at cad 0 nid 1 on hdac1 kld snd_hda [MPSAFE] (1p:1v/1r:1v channels duplex)
Код: Выделить всё
cat dmesg.boot
Copyright (c) 1992-2009 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.0-RELEASE-p1 #0: Fri Dec 4 00:27:51 EET 2009
root@barton:/usr/obj/usr/src/sys/amd64
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: AMD Athlon(tm) II X4 620 Processor (2611.82-MHz K8-class CPU)
Origin = "AuthenticAMD" Id = 0x100f52 Stepping = 2
Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT>
Features2=0x802009<SSE3,MON,CX16,POPCNT>
AMD Features=0xee500800<SYSCALL,NX,MMX+,FFXSR,Page1GB,RDTSCP,LM,3DNow!+,3DNow!>
AMD Features2=0x37ff<LAHF,CMP,SVM,ExtAPIC,CR8,ABM,SSE4A,MAS,Prefetch,OSVW,IBS,SKINIT,WDT>
TSC: P-state invariant
real memory = 4294967296 (4096 MB)
avail memory = 3971100672 (3787 MB)
ACPI APIC Table: <GBT GBTUACPI>
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
FreeBSD/SMP: 1 package(s) x 4 core(s)
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
cpu2 (AP): APIC ID: 2
cpu3 (AP): APIC ID: 3
ioapic0: Changing APIC ID to 2
ioapic0 <Version 2.1> irqs 0-23 on motherboard
kbd1 at kbdmux0
cryptosoft0: <software crypto> on motherboard
acpi0: <GBT GBTUACPI> on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
acpi0: reservation of 0, a0000 (3) failed
acpi0: reservation of 100000, cfde0000 (3) failed
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <32-bit timer at 3.579545MHz> port 0x4008-0x400b on acpi0
acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
Timecounter "HPET" frequency 14318180 Hz quality 900
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
pci1: <ACPI PCI bus> on pcib1
vgapci0: <VGA-compatible display> port 0xee00-0xeeff mem 0xd8000000-0xdfffffff,0xfdfe0000-0xfdfeffff,0xfde00000-0xfdefffff irq 18 at device 5.0 on pci1
drm0: <ATI Radeon HD 4200> on vgapci0
info: [drm] MSI enabled 1 message(s)
vgapci0: child drm0 requested pci_enable_busmaster
info: [drm] Initialized radeon 1.29.0 20080528
hdac0: <ATI (Unknown) High Definition Audio Controller> mem 0xfdffc000-0xfdffffff irq 19 at device 5.1 on pci1
hdac0: HDA Driver Revision: 20090624_0136
hdac0: [ITHREAD]
pcib2: <ACPI PCI-PCI bridge> irq 18 at device 10.0 on pci0
pci2: <ACPI PCI bus> on pcib2
re0: <RealTek 8168/8168B/8168C/8168CP/8168D/8168DP/8111B/8111C/8111CP/8111DP PCIe Gigabit Ethernet> port 0xde00-0xdeff mem 0xfdaff000-0xfdafffff,0xfdae0000-0xfdaeffff irq 18 at device 0.0 on pci2
re0: Using 1 MSI messages
re0: Chip rev. 0x3c000000
re0: MAC rev. 0x00400000
miibus0: <MII bus> on re0
rgephy0: <RTL8169S/8110S/8211B media interface> PHY 1 on miibus0
rgephy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
re0: Ethernet address: 00:24:1d:d7:ed:b4
re0: [FILTER]
atapci0: <ATI IXP700/800 SATA300 controller> port 0xff00-0xff07,0xfe00-0xfe03,0xfd00-0xfd07,0xfc00-0xfc03,0xfb00-0xfb0f mem 0xfe02f000-0xfe02f3ff irq 22 at device 17.0 on pci0
atapci0: [ITHREAD]
atapci0: AHCI v1.10 controller with 4 3Gbps ports, PM supported
ata2: <ATA channel 0> on atapci0
ata2: [ITHREAD]
ata3: <ATA channel 1> on atapci0
ata3: [ITHREAD]
ata4: <ATA channel 2> on atapci0
ata4: [ITHREAD]
ata5: <ATA channel 3> on atapci0
ata5: [ITHREAD]
ohci0: <OHCI (generic) USB controller> mem 0xfe02e000-0xfe02efff irq 16 at device 18.0 on pci0
ohci0: [ITHREAD]
usbus0: <OHCI (generic) USB controller> on ohci0
ohci1: <OHCI (generic) USB controller> mem 0xfe02d000-0xfe02dfff irq 16 at device 18.1 on pci0
ohci1: [ITHREAD]
usbus1: <OHCI (generic) USB controller> on ohci1
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xfe02c000-0xfe02c0ff irq 17 at device 18.2 on pci0
ehci0: [ITHREAD]
usbus2: EHCI version 1.0
usbus2: <EHCI (generic) USB 2.0 controller> on ehci0
ohci2: <OHCI (generic) USB controller> mem 0xfe02b000-0xfe02bfff irq 18 at device 19.0 on pci0
ohci2: [ITHREAD]
usbus3: <OHCI (generic) USB controller> on ohci2
ohci3: <OHCI (generic) USB controller> mem 0xfe02a000-0xfe02afff irq 18 at device 19.1 on pci0
ohci3: [ITHREAD]
usbus4: <OHCI (generic) USB controller> on ohci3
ehci1: <EHCI (generic) USB 2.0 controller> mem 0xfe029000-0xfe0290ff irq 19 at device 19.2 on pci0
ehci1: [ITHREAD]
usbus5: EHCI version 1.0
usbus5: <EHCI (generic) USB 2.0 controller> on ehci1
pci0: <serial bus, SMBus> at device 20.0 (no driver attached)
atapci1: <ATI IXP700/800 UDMA133 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xfa00-0xfa0f at device 20.1 on pci0
ata0: <ATA channel 0> on atapci1
ata0: [ITHREAD]
ata1: <ATA channel 1> on atapci1
ata1: [ITHREAD]
hdac1: <ATI SB600 High Definition Audio Controller> mem 0xfe024000-0xfe027fff irq 16 at device 20.2 on pci0
hdac1: HDA Driver Revision: 20090624_0136
hdac1: [ITHREAD]
isab0: <PCI-ISA bridge> at device 20.3 on pci0
isa0: <ISA bus> on isab0
pcib3: <ACPI PCI-PCI bridge> at device 20.4 on pci0
pci3: <ACPI PCI bus> on pcib3
re1: <RealTek 8169/8169S/8169SB(L)/8110S/8110SB(L) Gigabit Ethernet> port 0xce00-0xceff mem 0xfdcff000-0xfdcff0ff irq 20 at device 6.0 on pci3
re1: Chip rev. 0x10000000
re1: MAC rev. 0x00000000
miibus1: <MII bus> on re1
rgephy1: <RTL8169S/8110S/8211B media interface> PHY 1 on miibus1
rgephy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
re1: Ethernet address: 00:06:4f:77:45:c2
re1: [FILTER]
ath0: <Atheros 5212> mem 0xfdce0000-0xfdceffff irq 21 at device 7.0 on pci3
ath0: [ITHREAD]
ath0: AR2413 mac 7.9 RF2413 phy 4.5
ohci4: <OHCI (generic) USB controller> mem 0xfe028000-0xfe028fff irq 18 at device 20.5 on pci0
ohci4: [ITHREAD]
usbus6: <OHCI (generic) USB controller> on ohci4
fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: [FILTER]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
uart0: [FILTER]
ppc0: <Parallel port> port 0x378-0x37f irq 7 on acpi0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppc0: [ITHREAD]
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
plip0: [ITHREAD]
lpt0: <Printer> on ppbus0
lpt0: [ITHREAD]
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
atrtc0: <AT realtime clock> port 0x70-0x73 on acpi0
cpu0: <ACPI CPU> on acpi0
hwpstate0: <Cool`n'Quiet 2.0> on cpu0
cpu1: <ACPI CPU> on acpi0
cpu2: <ACPI CPU> on acpi0
cpu3: <ACPI CPU> on acpi0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
ZFS NOTICE: Prefetch is disabled by default if less than 4GB of RAM is present;
to enable, add "vfs.zfs.prefetch_disable=0" to /boot/loader.conf.
ZFS filesystem version 13
ZFS storage pool version 13
Timecounters tick every 1.000 msec
IPsec: Initialized Security Association Processing.
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 480Mbps High Speed USB v2.0
usbus3: 12Mbps Full Speed USB v1.0
usbus4: 12Mbps Full Speed USB v1.0
usbus5: 480Mbps High Speed USB v2.0
usbus6: 12Mbps Full Speed USB v1.0
ugen0.1: <ATI> at usbus0
uhub0: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen1.1: <ATI> at usbus1
uhub1: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
ugen2.1: <ATI> at usbus2
uhub2: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2
ugen3.1: <ATI> at usbus3
uhub3: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
ugen4.1: <ATI> at usbus4
uhub4: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4
ugen5.1: <ATI> at usbus5
uhub5: <ATI EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus5
ugen6.1: <ATI> at usbus6
uhub6: <ATI OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus6
acd0: CDRW <HL-DT-ST GCE-8527B/1.04> at ata0-master UDMA33
ad4: 476940MB <SAMSUNG HD502HJ 1AJ100E4> at ata2-master SATA300
ad8: 476940MB <WDC WD5000AAKB-00YSA0 12.01C02> at ata4-master SATA150
ad10: 610480MB <WDC WD6400AAKS-65A7B0 01.03B01> at ata5-master SATA300
hdac0: HDA Codec #0: ATI RS690/780 HDMI
pcm0: <HDA ATI RS690/780 HDMI PCM #0 Digital> at cad 0 nid 1 on hdac0
hdac1: HDA Codec #0: Realtek ALC885
pcm1: <HDA Realtek ALC885 PCM #0 Analog> at cad 0 nid 1 on hdac1
pcm2: <HDA Realtek ALC885 PCM #1 Analog> at cad 0 nid 1 on hdac1
pcm3: <HDA Realtek ALC885 PCM #2 Digital> at cad 0 nid 1 on hdac1
SMP: AP CPU #1 Launched!
SMP: AP CPU #2 Launched!
SMP: AP CPU #3 Launched!
uhub6: 2 ports with 2 removable, self powered
uhub0: 3 ports with 3 removable, self powered
uhub1: 3 ports with 3 removable, self powered
uhub3: 3 ports with 3 removable, self powered
uhub4: 3 ports with 3 removable, self powered
Root mount waiting for: usbus5 usbus2
Root mount waiting for: usbus5 usbus2
uhub2: 6 ports with 6 removable, self powered
uhub5: 6 ports with 6 removable, self powered
Trying to mount root from zfs:barton
ugen1.2: <GASIA> at usbus1
ukbd0: <GASIA PS2toUSB Adapter, class 0/0, rev 1.10/1.00, addr 2> on usbus1
kbd2 at ukbd0
ums0: <GASIA PS2toUSB Adapter, class 0/0, rev 1.10/1.00, addr 2> on usbus1
ums0: 5 buttons and [XYZ] coordinates ID=1
wlan0: Ethernet address: 00:24:01:0e:b9:a3
re0: link state changed to UP
